user/sven/linux.git, branch v3.12.39

Linux 3.12.39

2015-03-16T13:59:32Z

clk-gate: fix bit # check in clk_register_gate()

2015-03-16T13:58:21Z

commit 2e9dcdae4068460c45a308dd891be5248260251c upstream. In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit # should be no higher than 15, however the corresponding check is obviously off- by-one. Fixes: 045779942c04 ("clk: gate: add CLK_GATE_HIWORD_MASK") Signed-off-by: Sergei Shtylyov Signed-off-by: Michael Turquette Signed-off-by: Jiri Slaby

ath5k: fix spontaneus AR5312 freezes

2015-03-16T13:58:21Z

commit 8bfae4f9938b6c1f033a5159febe97e441d6d526 upstream. Sometimes while CPU have some load and ath5k doing the wireless interface reset the whole WiSoC completely freezes. Set of tests shows that using atomic delay function while we wait interface reset helps to avoid such freezes. The easiest way to reproduce this issue: create a station interface, start continous scan with wpa_supplicant and load CPU by something. Or just create multiple station interfaces and put them all in continous scan. This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use usleep_range where possible"), which replaces initial udelay() by usleep_range(). I do not know actual source of this issue, but all looks like that HW freeze is caused by transaction on internal SoC bus, while wireless block is in reset state. Also I should note that I do not know how many chips are affected, but I did not see this issue with chips, other than AR5312. CC: Jiri Slaby CC: Nick Kossifidis CC: Luis R. Rodriguez Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible") Reported-by: Christophe Prevotaux Tested-by: Christophe Prevotaux Tested-by: Eric Bree Signed-off-by: Sergey Ryazanov Signed-off-by: Kalle Valo Signed-off-by: Jiri Slaby

NFSv4: Don't call put_rpccred() under the rcu_read_lock()

2015-03-16T13:58:20Z

commit 7c0af9ffb7bb4e5355470fa60b3eb711ddf226fa upstream. put_rpccred() can sleep. Fixes: 8f649c3762547 ("NFSv4: Fix the locking in nfs_inode_reclaim_delegation()") Signed-off-by: Trond Myklebust Signed-off-by: Jiri Slaby

ACPI / video: Load the module even if ACPI is disabled

2015-03-16T13:58:20Z

commit 6e17cb12881ba8d5e456b89f072dc6b70048af36 upstream. i915.ko depends upon the acpi/video.ko module and so refuses to load if ACPI is disabled at runtime if for example the BIOS is broken beyond repair. acpi/video provides an optional service for i915.ko and so we should just allow the modules to load, but do no nothing in order to let the machines boot correctly. Reported-by: Bill Augur Signed-off-by: Chris Wilson Cc: Daniel Vetter Cc: Jani Nikula Acked-by: Aaron Lu [ rjw: Fixed up the new comment in acpi_video_init() ] Signed-off-by: Rafael J. Wysocki Signed-off-by: Jiri Slaby

drm/radeon: fix 1 RB harvest config setup for TN/RL

2015-03-16T13:58:19Z

commit dbfb00c3e7e18439f2ebf67fe99bf7a50b5bae1e upstream. The logic was reversed from what the hw actually exposed. Fixes graphics corruption in certain harvest configurations. Signed-off-by: Alex Deucher Signed-off-by: Jiri Slaby

drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh

2015-03-16T13:58:19Z

commit 3d2d98ee1af0cf6eebfbd6bff4c17d3601ac1284 upstream. Just in case it hasn't been calculated for the mode. Signed-off-by: Alex Deucher Signed-off-by: Jiri Slaby

HID: fixup the conflicting keyboard mappings quirk

2015-03-16T13:58:18Z

commit 8e7b341037db1835ee6eea64663013cbfcf33575 upstream. The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion on conflicting mappings") needs to properly check for VARIABLE reports as well (ARRAY reports should be ignored), otherwise legitimate keyboards might break. Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings") Reported-by: Fredrik Hallenberg Reported-by: David Herrmann Signed-off-by: Jiri Kosina Signed-off-by: Jiri Slaby

HID: input: fix confusion on conflicting mappings

2015-03-16T13:58:18Z

commit 6ce901eb61aa30ba8565c62049ee80c90728ef14 upstream. On an PC-101/103/104 keyboard (American layout) the 'Enter' key and its neighbours look like this: +---+ +---+ +-------+ | 1 | | 2 | | 5 | +---+ +---+ +-------+ +---+ +-----------+ | 3 | | 4 | +---+ +-----------+ On a PC-102/105 keyboard (European layout) it looks like this: +---+ +---+ +-------+ | 1 | | 2 | | | +---+ +---+ +-+ 4 | +---+ +---+ | | | 3 | | 5 | | | +---+ +---+ +-----+ (Note that the number of keys is the same, but key '5' is moved down and the shape of key '4' is changed. Keys '1' to '3' are exactly the same.) The keys 1-4 report the same scan-code in HID in both layouts, even though the keysym they produce is usually different depending on the XKB-keymap used by user-space. However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout and 0x32 for the lower layout, as defined by the HID spec. This is highly confusing as the linux-input API uses a single keycode for both. So far, this was never a problem as there never has been a keyboard with both of those keys present at the same time. It would have to look something like this: +---+ +---+ +-------+ | 1 | | 2 | | x31 | +---+ +---+ +-------+ +---+ +---+ +-----+ | 3 | |x32| | 4 | +---+ +---+ +-----+ HID can represent such a keyboard, but the linux-input API cannot. Furthermore, any user-space mapping would be confused by this and, luckily, no-one ever produced such hardware. Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys is present on a hardware, this works just fine. Lets introduce hardware-vendors into this: ------------------------------------------ Unfortunately, it seems way to expensive to produce a different device for American and European layouts. Therefore, hardware-vendors put both keys, (0x31 and 0x32) on the same keyboard, but only one of them is hooked up to the physical button, the other one is 'dead'. This means, they can use the same hardware, with a different button-layout and automatically produce the correct HID events for American *and* European layouts. This is unproblematic for normal keyboards, as the 'dead' key will never report any KEY-DOWN events. But RollOver keyboards send the whole matrix on each key-event, allowing n-key roll-over mode. This means, we get a 0x31 and 0x32 event on each key-press. One of them will always be 0, the other reports the real state. As we map both to the same keycode, we will get spurious key-events, even though the real key-state never changed. The easiest way would be to blacklist 'dead' keys and never handle those. We could simply read the 'country' tag of USB devices and blacklist either key according to the layout. But... hardware vendors... want the same device for all countries and thus many of them set 'country' to 0 for all devices. Meh.. So we have to deal with this properly. As we cannot know which of the keys is 'dead', we either need a heuristic and track those keys, or we simply make use of our value-tracking for HID fields. We simply ignore HID events for absolute data if the data didn't change. As HID tracks events on the HID level, we haven't done the keycode translation, yet. Therefore, the 'dead' key is tracked independently of the real key, therefore, any events on it will be ignored. This patch simply discards any HID events for absolute data if it didn't change compared to the last report. We need to ignore relative and buffered-byte reports for obvious reasons. But those cannot be affected by this bug, so we're fine. Preferably, we'd do this filtering on the HID-core level. But this might break a lot of custom drivers, if they do not follow the HID specs. Therefore, we do this late in hid-input just before we inject it into the input layer (which does the exact same filtering, but on the keycode level). If this turns out to break some devices, we might have to limit filtering to EV_KEY events. But lets try to do the Right Thing first, and properly filter any absolute data that didn't change. This patch is tagged for 'stable' as it fixes a lot of n-key RollOver hardware. We might wanna wait with backporting for a while, before we know it doesn't break anything else, though. Reported-by: Adam Goode Reported-by: Fredrik Hallenberg Tested-by: Fredrik Hallenberg Signed-off-by: David Herrmann Signed-off-by: Jiri Kosina Signed-off-by: Jiri Slaby

dm snapshot: fix a possible invalid memory access on unload

2015-03-16T13:58:18Z

commit 22aa66a3ee5b61e0f4a0bfeabcaa567861109ec3 upstream. When the snapshot target is unloaded, snapshot_dtr() waits until pending_exceptions_count drops to zero. Then, it destroys the snapshot. Therefore, the function that decrements pending_exceptions_count should not touch the snapshot structure after the decrement. pending_complete() calls free_pending_exception(), which decrements pending_exceptions_count, and then it performs up_write(&s->lock) and it calls retry_origin_bios() which dereferences s->origin. These two memory accesses to the fields of the snapshot may touch the dm_snapshot struture after it is freed. This patch moves the call to free_pending_exception() to the end of pending_complete(), so that the snapshot will not be destroyed while pending_complete() is in progress. Signed-off-by: Mikulas Patocka Signed-off-by: Mike Snitzer Signed-off-by: Jiri Slaby