user/sven/linux.git, branch v3.13.10

Linux 3.13.10

2014-04-14T13:48:24Z

crypto: ghash-clmulni-intel - use C implementation for setkey()

2014-04-14T13:47:22Z

commit 8ceee72808d1ae3fb191284afc2257a2be964725 upstream. The GHASH setkey() function uses SSE registers but fails to call kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and then having to deal with the restriction that they cannot be called from interrupt context, move the setkey() implementation to the C domain. Note that setkey() does not use any particular SSE features and is not expected to become a performance bottleneck. Signed-off-by: Ard Biesheuvel Acked-by: H. Peter Anvin Fixes: 0e1227d356e9b (crypto: ghash - Add PCLMULQDQ accelerated implementation) Signed-off-by: Herbert Xu Signed-off-by: Greg Kroah-Hartman

m68k: Skip futex_atomic_cmpxchg_inatomic() test

2014-04-14T13:47:22Z

commit e571c58f313d35c56e0018470e3375ddd1fd320e upstream. Skip the futex_atomic_cmpxchg_inatomic() test in futex_init(). It causes a fatal exception on 68030 (and presumably 68020 also). Signed-off-by: Finn Thain Acked-by: Geert Uytterhoeven Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1403061006440.5525@nippy.intranet Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test

2014-04-14T13:47:22Z

commit 03b8c7b623c80af264c4c8d6111e5c6289933666 upstream. If an architecture has futex_atomic_cmpxchg_inatomic() implemented and there is no runtime check necessary, allow to skip the test within futex_init(). This allows to get rid of some code which would always give the same result, and also allows the compiler to optimize a couple of if statements away. Signed-off-by: Heiko Carstens Cc: Finn Thain Cc: Geert Uytterhoeven Link: http://lkml.kernel.org/r/20140302120947.GA3641@osiris Signed-off-by: Thomas Gleixner [geert: Backported to v3.10..v3.13] Signed-off-by: Geert Uytterhoeven Signed-off-by: Greg Kroah-Hartman

ARC: [nsimosci] Unbork console

2014-04-14T13:47:22Z

commit 61fb4bfc010b0d2940f7fd87acbce6a0f03217cb upstream. Despite the switch to right UART driver (prev patch), serial console still doesn't work due to missing CONFIG_SERIAL_OF_PLATFORM Also fix the default cmdline in DT to not refer to out-of-tree ARC framebuffer driver for console. Signed-off-by: Vineet Gupta Cc: Francois Bedard Signed-off-by: Greg Kroah-Hartman

ARC: [nsimosci] Change .dts to use generic 8250 UART

2014-04-14T13:47:22Z

commit 6eda477b3c54b8236868c8784e5e042ff14244f0 upstream. The Synopsys APB DW UART has a couple of special features that are not in the System C model. In 3.8, the 8250_dw driver didn't really use these features, but from 3.9 onwards, the 8250_dw driver has become incompatible with our model. Signed-off-by: Mischa Jonker Signed-off-by: Vineet Gupta Cc: Francois Bedard Signed-off-by: Greg Kroah-Hartman

powernow-k6: reorder frequencies

2014-04-14T13:47:22Z

commit 22c73795b101597051924556dce019385a1e2fa0 upstream. This patch reorders reported frequencies from the highest to the lowest, just like in other frequency drivers. Signed-off-by: Mikulas Patocka Acked-by: Viresh Kumar Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

powernow-k6: correctly initialize default parameters

2014-04-14T13:47:22Z

commit d82b922a4acc1781d368aceac2f9da43b038cab2 upstream. The powernow-k6 driver used to read the initial multiplier from the powernow register. However, there is a problem with this: * If there was a frequency transition before, the multiplier read from the register corresponds to the current multiplier. * If there was no frequency transition since reset, the field in the register always reads as zero, regardless of the current multiplier that is set using switches on the mainboard and that the CPU is running at. The zero value corresponds to multiplier 4.5, so as a consequence, the powernow-k6 driver always assumes multiplier 4.5. For example, if we have 550MHz CPU with bus frequency 100MHz and multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5 and bus frequency is 122MHz. The powernow-k6 driver then sets the multiplier to 4.5, underclocking the CPU to 450MHz, but reports the current frequency as 550MHz. There is no reliable way how to read the initial multiplier. I modified the driver so that it contains a table of known frequencies (based on parameters of existing CPUs and some common overclocking schemes) and sets the multiplier according to the frequency. If the frequency is unknown (because of unusual overclocking or underclocking), the user must supply the bus speed and maximum multiplier as module parameters. This patch should be backported to all stable kernels. If it doesn't apply cleanly, change it, or ask me to change it. Signed-off-by: Mikulas Patocka Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

powernow-k6: disable cache when changing frequency

2014-04-14T13:47:22Z

commit e20e1d0ac02308e2211306fc67abcd0b2668fb8b upstream. I found out that a system with k6-3+ processor is unstable during network server load. The system locks up or the network card stops receiving. The reason for the instability is the CPU frequency scaling. During frequency transition the processor is in "EPM Stop Grant" state. The documentation says that the processor doesn't respond to inquiry requests in this state. Consequently, coherency of processor caches and bus master devices is not maintained, causing the system instability. This patch flushes the cache during frequency transition. It fixes the instability. Other minor changes: * u64 invalue changed to unsigned long because the variable is 32-bit * move the logic to set the multiplier to a separate function powernow_k6_set_cpu_multiplier * preserve lower 5 bits of the powernow port instead of 4 (the voltage field has 5 bits) * mask interrupts when reading the multiplier, so that the port is not open during other activity (running other kernel code with the port open shouldn't cause any misbehavior, but we should better be safe and keep the port closed) This patch should be backported to all stable kernels. If it doesn't apply cleanly, change it, or ask me to change it. Signed-off-by: Mikulas Patocka Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

rds: prevent dereference of a NULL device in rds_iw_laddr_check

2014-04-14T13:47:22Z

[ Upstream commit bf39b4247b8799935ea91d90db250ab608a58e50 ] Binding might result in a NULL device which is later dereferenced without checking. Signed-off-by: Sasha Levin Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman