user/sven/linux.git, branch v4.14.65

Linux 4.14.65

2018-08-18T08:48:00Z

x86/speculation/l1tf: Exempt zeroed PTEs from inversion

2018-08-18T08:48:00Z

commit f19f5c49bbc3ffcc9126cc245fc1b24cc29f4a37 upstream. It turns out that we should *not* invert all not-present mappings, because the all zeroes case is obviously special. clear_page() does not undergo the XOR logic to invert the address bits, i.e. PTE, PMD and PUD entries that have not been individually written will have val=0 and so will trigger __pte_needs_invert(). As a result, {pte,pmd,pud}_pfn() will return the wrong PFN value, i.e. all ones (adjusted by the max PFN mask) instead of zero. A zeroed entry is ok because the page at physical address 0 is reserved early in boot specifically to mitigate L1TF, so explicitly exempt them from the inversion when reading the PFN. Manifested as an unexpected mprotect(..., PROT_NONE) failure when called on a VMA that has VM_PFNMAP and was mmap'd to as something other than PROT_NONE but never used. mprotect() sends the PROT_NONE request down prot_none_walk(), which walks the PTEs to check the PFNs. prot_none_pte_entry() gets the bogus PFN from pte_pfn() and returns -EACCES because it thinks mprotect() is trying to adjust a high MMIO address. [ This is a very modified version of Sean's original patch, but all credit goes to Sean for doing this and also pointing out that sometimes the __pte_needs_invert() function only gets the protection bits, not the full eventual pte. But zero remains special even in just protection bits, so that's ok. - Linus ] Fixes: f22cc87f6c1f ("x86/speculation/l1tf: Invert all not present mappings") Signed-off-by: Sean Christopherson Acked-by: Andi Kleen Cc: Thomas Gleixner Cc: Josh Poimboeuf Cc: Michal Hocko Cc: Vlastimil Babka Cc: Dave Hansen Cc: Greg Kroah-Hartman Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

Linux 4.14.64

2018-08-17T19:01:12Z

x86/mm: Add TLB purge to free pmd/pte page interfaces

2018-08-17T19:01:11Z

commit 5e0fb5df2ee871b841f96f9cb6a7f2784e96aa4e upstream. ioremap() calls pud_free_pmd_page() / pmd_free_pte_page() when it creates a pud / pmd map. The following preconditions are met at their entry. - All pte entries for a target pud/pmd address range have been cleared. - System-wide TLB purges have been peformed for a target pud/pmd address range. The preconditions assure that there is no stale TLB entry for the range. Speculation may not cache TLB entries since it requires all levels of page entries, including ptes, to have P & A-bits set for an associated address. However, speculation may cache pud/pmd entries (paging-structure caches) when they have P-bit set. Add a system-wide TLB purge (INVLPG) to a single page after clearing pud/pmd entry's P-bit. SDM 4.10.4.1, Operation that Invalidate TLBs and Paging-Structure Caches, states that: INVLPG invalidates all paging-structure caches associated with the current PCID regardless of the liner addresses to which they correspond. Fixes: 28ee90fe6048 ("x86/mm: implement free pmd/pte page interfaces") Signed-off-by: Toshi Kani Signed-off-by: Thomas Gleixner Cc: mhocko@suse.com Cc: akpm@linux-foundation.org Cc: hpa@zytor.com Cc: cpandya@codeaurora.org Cc: linux-mm@kvack.org Cc: linux-arm-kernel@lists.infradead.org Cc: Joerg Roedel Cc: stable@vger.kernel.org Cc: Andrew Morton Cc: Michal Hocko Cc: "H. Peter Anvin" Cc: Link: https://lkml.kernel.org/r/20180627141348.21777-4-toshi.kani@hpe.com Signed-off-by: Greg Kroah-Hartman

ioremap: Update pgtable free interfaces with addr

2018-08-17T19:01:11Z

commit 785a19f9d1dd8a4ab2d0633be4656653bd3de1fc upstream. The following kernel panic was observed on ARM64 platform due to a stale TLB entry. 1. ioremap with 4K size, a valid pte page table is set. 2. iounmap it, its pte entry is set to 0. 3. ioremap the same address with 2M size, update its pmd entry with a new value. 4. CPU may hit an exception because the old pmd entry is still in TLB, which leads to a kernel panic. Commit b6bdb7517c3d ("mm/vmalloc: add interfaces to free unmapped page table") has addressed this panic by falling to pte mappings in the above case on ARM64. To support pmd mappings in all cases, TLB purge needs to be performed in this case on ARM64. Add a new arg, 'addr', to pud_free_pmd_page() and pmd_free_pte_page() so that TLB purge can be added later in seprate patches. [toshi.kani@hpe.com: merge changes, rewrite patch description] Fixes: 28ee90fe6048 ("x86/mm: implement free pmd/pte page interfaces") Signed-off-by: Chintan Pandya Signed-off-by: Toshi Kani Signed-off-by: Thomas Gleixner Cc: mhocko@suse.com Cc: akpm@linux-foundation.org Cc: hpa@zytor.com Cc: linux-mm@kvack.org Cc: linux-arm-kernel@lists.infradead.org Cc: Will Deacon Cc: Joerg Roedel Cc: stable@vger.kernel.org Cc: Andrew Morton Cc: Michal Hocko Cc: "H. Peter Anvin" Cc: Link: https://lkml.kernel.org/r/20180627141348.21777-3-toshi.kani@hpe.com Signed-off-by: Greg Kroah-Hartman

Bluetooth: hidp: buffer overflow in hidp_process_report

2018-08-17T19:01:11Z

commit 7992c18810e568b95c869b227137a2215702a805 upstream. CVE-2018-9363 The buffer length is unsigned at all layers, but gets cast to int and checked in hidp_process_report and can lead to a buffer overflow. Switch len parameter to unsigned int to resolve issue. This affects 3.18 and newer kernels. Signed-off-by: Mark Salyzyn Fixes: a4b1b5877b514b276f0f31efe02388a9c2836728 ("HID: Bluetooth: hidp: make sure input buffers are big enough") Cc: Marcel Holtmann Cc: Johan Hedberg Cc: "David S. Miller" Cc: Kees Cook Cc: Benjamin Tissoires Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: security@kernel.org Cc: kernel-team@android.com Acked-by: Kees Cook Signed-off-by: Marcel Holtmann Signed-off-by: Greg Kroah-Hartman

ASoC: Intel: cht_bsw_max98090_ti: Fix jack initialization

2018-08-17T19:01:11Z

commit 3bbda5a38601f7675a214be2044e41d7749e6c7b upstream. If the ts3a227e audio accessory detection hardware is present and its driver probed, the jack needs to be created before enabling jack detection in the ts3a227e driver. With this patch, the jack is instantiated in the max98090 headset init function if the ts3a227e is present. This fixes a null pointer dereference as the jack detection enabling function in the ts3a driver was called before the jack is created. [minor correction to keep error handling on jack creation the same as before by Pierre Bossart] Signed-off-by: Thierry Escande Signed-off-by: Pierre-Louis Bossart Acked-By: Vinod Koul Signed-off-by: Mark Brown Signed-off-by: Sudip Mukherjee Signed-off-by: Greg Kroah-Hartman

ASoC: msm8916-wcd-digital: fix RX2 MIX1 and RX3 MIX1

2018-08-17T19:01:11Z

commit f53ee247ad546183fc13739adafc5579b9f0ebc0 upstream. The kcontrol for the third input (rxN_mix1_inp3) of both RX2 and RX3 mixers are not using the correct control register. This simple patch fixes this. Signed-off-by: Jean-François Têtu Signed-off-by: Mark Brown Signed-off-by: Sudip Mukherjee Signed-off-by: Greg Kroah-Hartman

block, bfq: fix wrong init of saved start time for weight raising

2018-08-17T19:01:11Z

commit 4baa8bb13f41307f3eb62fe91f93a1a798ebef53 upstream. This commit fixes a bug that causes bfq to fail to guarantee a high responsiveness on some drives, if there is heavy random read+write I/O in the background. More precisely, such a failure allowed this bug to be found [1], but the bug may well cause other yet unreported anomalies. BFQ raises the weight of the bfq_queues associated with soft real-time applications, to privilege the I/O, and thus reduce latency, for these applications. This mechanism is named soft-real-time weight raising in BFQ. A soft real-time period may happen to be nested into an interactive weight raising period, i.e., it may happen that, when a bfq_queue switches to a soft real-time weight-raised state, the bfq_queue is already being weight-raised because deemed interactive too. In this case, BFQ saves in a special variable wr_start_at_switch_to_srt, the time instant when the interactive weight-raising period started for the bfq_queue, i.e., the time instant when BFQ started to deem the bfq_queue interactive. This value is then used to check whether the interactive weight-raising period would still be in progress when the soft real-time weight-raising period ends. If so, interactive weight raising is restored for the bfq_queue. This restore is useful, in particular, because it prevents bfq_queues from losing their interactive weight raising prematurely, as a consequence of spurious, short-lived soft real-time weight-raising periods caused by wrong detections as soft real-time. If, instead, a bfq_queue switches to soft-real-time weight raising while it *is not* already in an interactive weight-raising period, then the variable wr_start_at_switch_to_srt has no meaning during the following soft real-time weight-raising period. Unfortunately the handling of this case is wrong in BFQ: not only the variable is not flagged somehow as meaningless, but it is also set to the time when the switch to soft real-time weight-raising occurs. This may cause an interactive weight-raising period to be considered mistakenly as still in progress, and thus a spurious interactive weight-raising period to start for the bfq_queue, at the end of the soft-real-time weight-raising period. In particular the spurious interactive weight-raising period will be considered as still in progress, if the soft-real-time weight-raising period does not last very long. The bfq_queue will then be wrongly privileged and, if I/O bound, will unjustly steal bandwidth to truly interactive or soft real-time bfq_queues, harming responsiveness and low latency. This commit fixes this issue by just setting wr_start_at_switch_to_srt to minus infinity (farthest past time instant according to jiffies macros): when the soft-real-time weight-raising period ends, certainly no interactive weight-raising period will be considered as still in progress. [1] Background I/O Type: Random - Background I/O mix: Reads and writes - Application to start: LibreOffice Writer in http://www.phoronix.com/scan.php?page=news_item&px=Linux-4.13-IO-Laptop Signed-off-by: Paolo Valente Signed-off-by: Angelo Ruocco Tested-by: Oleksandr Natalenko Tested-by: Lee Tibbert Tested-by: Mirko Montanari Signed-off-by: Jens Axboe Signed-off-by: Sudip Mukherjee Signed-off-by: Greg Kroah-Hartman

clk: sunxi-ng: Fix missing CLK_SET_RATE_PARENT in ccu-sun4i-a10.c

2018-08-17T19:01:11Z

commit a894990ac994a53bc5a0cc694eb12f3c064c18c5 upstream. When using cpufreq-dt with default govenor other than "performance" system freezes while booting. Adding CLK_SET_RATE_PARENT | CLK_IS_CRITICAL to clk_cpu fixes the problem. Tested on Cubietruck (A20). Fixes: c84f5683f6E ("clk: sunxi-ng: Add sun4i/sun7i CCU driver") Acked-by: Chen-Yu Tsai Signed-off-by: Alexander Syring Signed-off-by: Maxime Ripard Signed-off-by: Sudip Mukherjee Signed-off-by: Greg Kroah-Hartman