user/sven/linux.git, branch v4.17.10

Linux 4.17.10

2018-07-25T09:26:13Z

xhci: Fix perceived dead host due to runtime suspend race with event handler

2018-07-25T09:26:13Z

commit 229bc19fd7aca4f37964af06e3583c1c8f36b5d6 upstream. Don't rely on event interrupt (EINT) bit alone to detect pending port change in resume. If no change event is detected the host may be suspended again, oterwise roothubs are resumed. There is a lag in xHC setting EINT. If we don't notice the pending change in resume, and the controller is runtime suspeded again, it causes the event handler to assume host is dead as it will fail to read xHC registers once PCI puts the controller to D3 state. [ 268.520969] xhci_hcd: xhci_resume: starting port polling. [ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling. [ 268.521030] xhci_hcd: xhci_suspend: stopping port polling. [ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001 [ 268.521139] xhci_hcd: Port Status Change Event for port 3 [ 268.521149] xhci_hcd: resume root hub [ 268.521163] xhci_hcd: port resume event for port 3 [ 268.521168] xhci_hcd: xHC is not running. [ 268.521174] xhci_hcd: handle_port_status: starting port polling. [ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead The EINT lag is described in a additional note in xhci specs 4.19.2: "Due to internal xHC scheduling and system delays, there will be a lag between a change bit being set and the Port Status Change Event that it generated being written to the Event Ring. If SW reads the PORTSC and sees a change bit set, there is no guarantee that the corresponding Port Status Change Event has already been written into the Event Ring." Cc: Signed-off-by: Mathias Nyman Signed-off-by: Kai-Heng Feng Signed-off-by: Greg Kroah-Hartman

cxl_getfile(): fix double-iput() on alloc_file() failures

2018-07-25T09:26:13Z

commit d202797f480c0e5918e7642d6716cdc62b3ab5c9 upstream. Doing iput() after path_put() is wrong. Cc: stable@vger.kernel.org Acked-by: Linus Torvalds Signed-off-by: Al Viro Signed-off-by: Greg Kroah-Hartman

drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()

2018-07-25T09:26:13Z

commit b4e7a7a88b5d060650094b8d3454bc521d669f6a upstream. Failure of ->open() should *not* be followed by fput(). Fixed by using filp_clone_open(), which gets the cleanups right. Cc: stable@vger.kernel.org Acked-by: Linus Torvalds Signed-off-by: Al Viro Signed-off-by: Greg Kroah-Hartman

alpha: fix osf_wait4() breakage

2018-07-25T09:26:12Z

commit f88a333b44318643282b8acc92af90deda441f5e upstream. kernel_wait4() expects a userland address for status - it's only rusage that goes as a kernel one (and needs a copyout afterwards) [ Also, fix the prototype of kernel_wait4() to have that __user annotation - Linus ] Fixes: 92ebce5ac55d ("osf_wait4: switch to kernel_wait4()") Cc: stable@kernel.org # v4.13+ Signed-off-by: Al Viro Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

net: usb: asix: replace mii_nway_restart in resume path

2018-07-25T09:26:12Z

[ Upstream commit 5c968f48021a9b3faa61ac2543cfab32461c0e05 ] mii_nway_restart is not pm aware which results in a rtnl deadlock. Implement mii_nway_restart manual by setting BMCR_ANRESTART if BMCR_ANENABLE is set. To reproduce: * plug an asix based usb network interface * wait until the device enters PM (~5 sec) * `ip link set eth1 up` will never return Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Signed-off-by: Alexander Couzens Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

ipv6: make DAD fail with enhanced DAD when nonce length differs

2018-07-25T09:26:12Z

[ Upstream commit e66515999b627368892ccc9b3a13a506f2ea1357 ] Commit adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") added enhanced DAD with a nonce length of 6 bytes. However, RFC7527 doesn't specify the length of the nonce, other than being 6 + 8*k bytes, with integer k >= 0 (RFC3971 5.3.2). The current implementation simply assumes that the nonce will always be 6 bytes, but others systems are free to choose different sizes. If another system sends a nonce of different length but with the same 6 bytes prefix, it shouldn't be considered as the same nonce. Thus, check that the length of the received nonce is the same as the length we sent. Ugly scapy test script running on veth0: def loop(): pkt=sniff(iface="veth0", filter="icmp6", count=1) pkt = pkt[0] b = bytearray(pkt[Raw].load) b[1] += 1 b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef' pkt[Raw].load = bytes(b) pkt[IPv6].plen += 8 # fixup checksum after modifying the payload pkt[IPv6].payload.cksum -= 0x3b44 if pkt[IPv6].payload.cksum < 0: pkt[IPv6].payload.cksum += 0xffff sendp(pkt, iface="veth0") This should result in DAD failure for any address added to veth0's peer, but is currently ignored. Fixes: adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by: Sabrina Dubroca Reviewed-by: Stefano Brivio Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: systemport: Fix CRC forwarding check for SYSTEMPORT Lite

2018-07-25T09:26:12Z

[ Upstream commit 9e3bff923913729d76d87f0015848ee7b8ff7083 ] SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit is not set by default. Fix the logic such that we properly check whether that bit is set or not and we don't forward an extra 4 bytes to the network stack. Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net/mlx4_en: Don't reuse RX page when XDP is set

2018-07-25T09:26:12Z

[ Upstream commit 432e629e56432064761be63bcd5e263c0920430d ] When a new rx packet arrives, the rx path will decide whether to reuse the remainder of the page or not according to one of the below conditions: 1. frag_info->frag_stride == PAGE_SIZE / 2 2. frags->page_offset + frag_info->frag_size > PAGE_SIZE; The first condition is no met for when XDP is set. For XDP, page_offset is always set to priv->rx_headroom which is XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some padding, still the 2nd release condition will hold since XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not be released and will be _wrongly_ reused for next free rx descriptor. In XDP there is an assumption to have a page per packet and reuse can break such assumption and might cause packet data corruptions. Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd case to avoid page reuse when XDP is set, since rx_headroom is set to 0 for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup. No additional cache line is required for the new condition. Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed Signed-off-by: Tariq Toukan Suggested-by: Martin KaFai Lau CC: Eric Dumazet Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: aquantia: vlan unicast address list correct handling

2018-07-25T09:26:12Z

[ Upstream commit 94b3b542303f3055c326df74ef144a8a790d7d7f ] Setting up macvlan/macvtap networks over atlantic NIC results in no traffic over these networks because ndo_set_rx_mode did not listed UC MACs as registered in unicast filter. Here we fix that taking into account maximum number of UC filters supported by hardware. If more than MAX addresses were registered, we just enable promisc and/or allmulti to pass the traffic in. We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since thats not a configurable parameter at all. Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.") Signed-off-by: Igor Russkikh Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman