user/sven/linux.git/Documentation/devicetree, branch stable/3.7.y

of/net/mdio-gpio: Fix pdev->id issue when using devicetrees.

2012-11-19T23:57:07Z

When the mdio-gpio driver is probed via device trees, the platform device id is set as -1, However the pdev->id is re-used as bus-id for while creating mdio gpio bus. So For device tree case the mdio-gpio bus name appears as "gpio-ffffffff" where as for non-device tree case the bus name appears as "gpio-" Which means the bus_id is fixed in device tree case, so we can't have two mdio gpio buses via device trees. Assigning a logical bus number via device tree solves the problem and the bus name is much consistent with non-device tree bus name. Without this patch 1. we can't support two mdio-gpio buses via device trees. 2. we should always pass gpio-ffffffff as bus name to phy_connect, very different to non-device tree bus name. So, setting up the bus_id via aliases from device tree is the right solution and other drivers do similar thing. Signed-off-by: Srinivas Kandagatla Signed-off-by: David S. Miller

Merge tag 'v3.7-rc3' into for-linus to sync up with recent USB changes

2012-10-30T07:09:18Z

Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2012-10-28T18:12:38Z

Pull arm-soc fixes from Arnd Bergmann: "Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91. These come a little later than I had hoped but unfortunately we had a few of these patches cause regressions themselves and had to work out how to deal with those in the meantime." * tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits) Revert "ARM i.MX25: Fix PWM per clock lookups" ARM: versatile: fix versatile_defconfig ARM: mvebu: update defconfig with 3.7 changes ARM: at91: fix at91x40 build ARM: socfpga: Fix socfpga compilation with early_printk() enabled ARM: SPEAr: Remove unused empty files MAINTAINERS: Add arm-soc tree entry ARM: dts: mxs: add the "clock-names" for gpmi-nand ARM: ux500: Correct SDI5 address and add some format changes ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE ARM: at91: drop duplicated config SOC_AT91SAM9 entry ARM: at91/i2c: change id to let i2c-at91 work ARM: at91/i2c: change id to let i2c-gpio work ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels. ARM: at91: fix external interrupt specification in board code ARM: at91: fix external interrupts in non-DT case ARM: at91: at91sam9g10: fix SOC type detection ARM: at91/tc: fix typo in the DT document ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500 ...

Input: egalax_ts - get gpio from devicetree

2012-10-25T07:38:22Z

The irq_to_gpio() is old, most platforms use GENERIC_GPIO framework and don't support this API anymore. The i.MX6q sabrelite platform equips an egalax touchscreen controller, and this platform already transfered to GENERIC_GPIO framework, to support this driver, we use a more generic way to get gpio. Add a return value checking for waking up the controller in the probe function, this guarantee only a workable device can pass init. [dmitry.torokhov@gmail.com: Make driver depend on CONFIG_OF as it is now required.] Acked-by Zhang Jiejing Reviewed-by: Shawn Guo Signed-off-by: Hui Wang Signed-off-by: Dmitry Torokhov

ARM: at91/tc: fix typo in the DT document

2012-10-24T16:04:08Z

Signed-off-by: Josh Wu Signed-off-by: Nicolas Ferre Acked-by: Jean-Christophe PLAGNIOL-VILLARD Cc: stable [v3.4]

dt: Document: correct tegra20/30 pinctrl slew-rate name

2012-10-17T17:45:35Z

change nvidia,slew_rate* to nvidia,slew-rate* Cc: stable@kernel.org Signed-off-by: Pritesh Raithatha Acked-by: Stephen Warren Tested-by: Stephen Warren Signed-off-by: Linus Walleij

Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux

2012-10-11T01:27:51Z

Pull i2c-embedded changes from Wolfram Sang: "The changes for i2c-embedded include: - massive rework of the omap driver - massive rework of the at91 driver. In fact, the old driver gets removed; I am okay with this approach since the old driver was depending on BROKEN and its limitations made it practically unusable, so people used bitbanging instead. But even if there are users, there is no platform_data or module parameter which would need to be converted. It is just another driver doing I2C transfers, just way better. Modifications of arch/arm/at91 related files have proper acks from the maintainer. - new driver for R-Car I2C - devicetree and generic_clock conversions and fixes - usual driver fixes and changes. The rework patches have come a long way and lots of people have been involved in creating/testing them. Most patches have been in linux-next at least since 3.6-rc5. A few have been added in the last week, I have to admit. An unexpected (but welcome :)) peak in private life is the cause for that. The "late" patches shouldn't cause any merge conflicts and I will have a special eye on them during the stabilization phase. This is an exception and I want to have the patches in place properly in time again for the next kernels." * 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits) MXS: Implement DMA support into mxs-i2c i2c: add Renesas R-Car I2C driver i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints i2c: nomadik: Add Device Tree support to the Nomadik I2C driver i2c: algo: pca: Fix chip reset function for PCA9665 i2c: mpc: Wait for STOP to hit the bus i2c: davinci: preparation for switch to common clock framework omap-i2c: fix incorrect log message when using a device tree i2c: omap: sanitize exit path i2c: omap: switch over to autosuspend API i2c: omap: remove unnecessary pm_runtime_suspended check i2c: omap: switch to threaded IRQ support i2c: omap: remove redundant status read i2c: omap: get rid of the "complete" label i2c: omap: resize fifos before each message i2c: omap: simplify IRQ exit path i2c: omap: always return IRQ_HANDLED i2c: omap: simplify errata check i2c: omap: bus: add a receiver flag ...

Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2012-10-11T01:21:48Z

Pull ARM SoC fixes from Olof Johansson: "A series of fixes (and in some cases, some cleanups): Via Tony Lindgren: - A collection of OMAP regression fixes, in particular because firmware no longer sets up all pin states before starting the kernel. - cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed). - A longer series of misc regression fixes and cleanups, warning removals, etc for OMAP From Arnd Bergmann: - A series of warning fixes for various platforms (defconfig builds) Misc: - A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc." * tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits) ARM: pxa: armcore: fix PCI PIO warnings ARM: integrator: use __iomem pointers for MMIO, part 2 ARM: assabet: fix bogus warning in get_assabet_scr (again) ARM: shmobile: mark shmobile_init_late as __init ARM: integrator_cp: fix build failure ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling ARM: OMAP3: fix workaround for EMU clockdomain arm/omap: Replace board_ref_clock with enum values ARM: OMAP2+: remove duplicated include from board-omap3stalker.c arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon arch/arm/mach-omap2: Remove unecessary semicolon arch/arm/mach-omap1/devices.c: Remove unecessary semicolon ARM/dts: omap5-evm: pinmux configuration for audio ARM/dts: Add pinctrl driver entries for omap5 ARM/dts: omap4-panda: pinmux configuration for audio ARM/dts: omap4-sdp: pinmux configuration for audio ARM/dts: omap5-evm: Disable unused McBSP3 ARM/dts: omap4-sdp: Disable unused McBSP3 ARM/dts: omap4-panda: Disable unused audio IPs ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs ...

Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm

2012-10-10T11:15:24Z

Pull pwm changes from Thierry Reding: "All legacy PWM providers have now been moved to the PWM subsystem. The plan for 3.8 is to adapt all board files to provide a lookup table for PWM devices in order to get rid of the global namespace. Subsequently, users of the legacy pwm_request() and pwm_free() functions can be migrated to the new pwm_get() and pwm_put() functions. Once this has been completed, the legacy API and the compatibility code in the core can be removed. In addition to the above, these changes also add support for configuring the polarity of a PWM signal (currently only supported on ECAP and EHRPWM) and include a much needed rework of the i.MX driver. Managed functions to obtain and release a PWM device (devm_pwm_get() and devm_pwm_put()) have been added and the pwm-backlight driver has been updated to use them. If the PWM subsystem hasn't been enabled, dummy functions are provided that allow the subsystem to safely compile out. Some common checks on input parameters have been moved to the core and removed from the drivers. Finally, a small fix corrects the description of the PWM specifier's second cell in the device tree representation." * tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits) pwm: dt: Fix description of second PWM cell pwm: Check for negative duty-cycle and period pwm: Add Ingenic JZ4740 support MIPS: JZ4740: Export timer API pwm: Move PUV3 PWM driver to PWM framework unicore32: pwm: Use managed resource allocations unicore32: pwm: Remove unnecessary indirection unicore32: pwm: Use module_platform_driver() unicore32: pwm: Properly remap memory-mapped registers pwm-backlight: Use devm_pwm_get() instead of pwm_get() pwm: Move AB8500 PWM driver to PWM framework pwm: Fix compilation error when CONFIG_PWM is not defined pwm: i.MX: fix clock lookup pwm: i.MX: use per clock unconditionally pwm: i.MX: add devicetree support pwm: i.MX: Use module_platform_driver pwm: i.MX: add functions to enable/disable pwm. pwm: i.MX: remove unnecessary if in pwm_[en|dis]able pwm: i.MX: factor out SoC specific functions pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM ...

Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

2012-10-10T01:58:42Z

Pull MMC updates from Chris Ball: "Core: - Add DT properties for card detection (broken-cd, cd-gpios, non-removable) - Don't poll non-removable devices - Fixup/rework eMMC sleep mode/"power off notify" feature - Support eMMC background operations (BKOPS). To set the one-time programmable fuse that enables bkops on an eMMC that doesn't already have it set, you can use the "mmc bkops enable" command in: git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git Drivers: - atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support - bfin_sdh: Add support for the controller in bf60x - dw_mmc: Support Samsung Exynos SoCs - eSDHC: Add ADMA support - sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit - sdhci-pltfm: Support broken-cd DT property - tegra: Convert to only supporting DT (mach-tegra has gone DT-only)" * tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits) mmc: core: Fixup broken suspend and eMMC4.5 power off notify mmc: sdhci-spear: Add clk_{un}prepare() support mmc: sdhci-spear: add device tree bindings mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks mmc: dt: Support "broken-cd" property in sdhci-pltfm mmc: sdhci-s3c: fix the wrong number of max bus clocks mmc: sh-mmcif: avoid oops on spurious interrupts mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ mmc: sdhci-s3c: Fix crash on module insertion for second time mmc: sdhci-s3c: Enable only required bus clock mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration" mmc: mxcmmc: fix bug that may block a data transfer forever mmc: omap_hsmmc: Pass on the suspend failure to the PM core mmc: atmel-mci: AP700x PDC is not connected to MCI mmc: atmel-mci: DMA can be used with other controllers mmc: mmci: use clk_prepare_enable and clk_disable_unprepare mmc: sdhci-s3c: Add device tree support mmc: dw_mmc: add support for exynos specific implementation of dw-mshc ...