user/sven/linux.git/drivers/amba, branch v4.11

ARM: 8596/1: amba: Support clk parents and rates assigned in DT

2016-08-12T15:47:07Z

Add the call to of_clk_set_defaults() into the amba probe path so that devices on the amba bus can use the assigned rates and parents feature of the common clock framework. Cc: Michael Turquette Tested-by: Jorge Ramirez Ortiz Signed-off-by: Stephen Boyd Signed-off-by: Russell King

ARM: 8566/1: drivers: amba: properly handle devices with power domains

2016-05-05T18:00:40Z

To read pid/cid registers, the probed device need to be properly turned on. When it is inside a power domain, the bus code should ensure that the given power domain is enabled before trying to access device's registers. However in some cases power domain (or clocks) might not be yet available. Returning -EPROBE_DEFER is not a solution in such case, because callers don't handle this special error code. Instead such devices are added to the special list and their registration is retried from periodic worker until all resources are available. Signed-off-by: Marek Szyprowski Signed-off-by: Russell King

amba: Hide TEGRA_AHB symbol

2015-11-24T15:47:25Z

The symbol depends on ARCH_TEGRA and will default to y. There are no circumstances under which it is desirable to disable this option. Signed-off-by: Thierry Reding

ARM: 8334/1: amba: tegra-ahb: detect and correct bogus base address

2015-04-02T09:03:55Z

amba: tegra-ahb: detect and correct bogus base address From a hardware SoC integration point of view, the starting address of this IP block in the existing Tegra SoC DT files is off by 4 bytes from the actual base address. Since we attempt to make old DT files forward-compatible with newer kernels, we cannot fix the IP block base address in old DT data. This patch works around the problem by detecting the four byte base address offset in the driver code, and correcting it if it's detected. (In general, IP block base addresses almost always have a null low byte.) Future SoC DT data for Tegra AHB should use the correct Tegra AHB base address, in cases where there is no DT data backward compatibility requirement. This patch is a revision of the patch originally titled "amba: tegra-ahb: use correct base address for future chip support". This revision implements changes requested by Russell King: http://marc.info/?l=linux-tegra&m=142658851825062&w=2 http://marc.info/?l=linux-tegra&m=142658873925178&w=2 Signed-off-by: Paul Walmsley Cc: Paul Walmsley Cc: Alexandre Courbot Cc: Hiroshi DOYU Cc: Stephen Warren Cc: Thierry Reding Cc: linux-kernel@vger.kernel.org Acked-by: Stephen Warren Signed-off-by: Russell King

ARM: 8333/1: amba: tegra-ahb: fix register offsets in the macros

2015-04-02T09:03:55Z

amba: tegra-ahb: fix register offsets in the macros From a hardware SoC integration point of view, the offsets of the Tegra AHB registers that are currently defined in tegra-ahb.c macros are all off by four bytes. Similarly, the starting address of this IP block in our existing DT files is also off by four bytes. Since we attempt to make old DT files forward-compatible with newer kernels, we cannot fix the IP block base address in old DT data. However, we can fix the offsets in the driver so that they are correct with respect to the hardware, which is what this patch does. And a subsequent patch will allow the offset to be removed for DT 'compatible' strings used in future DT files for newer Tegra chips that the kernel does not yet support. Signed-off-by: Paul Walmsley Cc: Paul Walmsley Cc: Alexandre Courbot Cc: Hiroshi DOYU Cc: Stephen Warren Cc: Thierry Reding Cc: linux-kernel@vger.kernel.org Acked-by: Stephen Warren Signed-off-by: Russell King

ARM: 8256/1: driver coamba: add device binding path 'driver_override'

2015-02-10T10:23:15Z

As already demonstrated with PCI [1] and the platform bus [2], a driver_override property in sysfs can be used to bypass the id matching of a device to a AMBA driver. This can be used by VFIO to bind to any AMBA device requested by the user. [1] http://lists-archives.com/linux-kernel/28030441-pci-introduce-new-device-binding-path-using-pci_dev-driver_override.html [2] https://www.redhat.com/archives/libvir-list/2014-April/msg00382.html Signed-off-by: Antonios Motakis Reviewed-by: Kim Phillips Signed-off-by: Russell King

Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

2014-12-15T00:43:47Z

Pull char/misc driver updates from Greg KH: "Here's the big char/misc driver update for 3.19-rc1 Lots of little things all over the place in different drivers, and a new subsystem, "coresight" has been added. Full details are in the shortlog" * tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits) parport: parport_pc, do not remove parent devices early spmi: Remove shutdown/suspend/resume kernel-doc carma-fpga-program: drop videobuf dependency carma-fpga: drop videobuf dependency carma-fpga-program.c: fix compile errors i8k: Fix temperature bug handling in i8k_get_temp() cxl: Name interrupts in /proc/interrupt CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning coresight-replicator: remove .owner field for driver coresight: fixed comments in coresight.h coresight: fix typo in comment in coresight-priv.h coresight: bindings for coresight drivers coresight: Adding ABI documentation w1: support auto-load of w1_bq27000 module. w1: avoid potential u16 overflow cn: verify msg->len before making callback mei: export fw status registers through sysfs mei: read and print all six FW status registers mei: txe: add cherrytrail device id mei: kill cached host and me csr values ...

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

2014-12-15T00:10:09Z

Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev__once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...

Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm

2014-12-12T23:26:48Z

Pull ARM updates from Russell King: "The major updates included in this update are: - Clang compatible stack pointer accesses by Behan Webster. - SA11x0 updates from Dmitry Eremin-Solenikov. - kgdb handling of breakpoints with read-only text/modules - Support for Privileged-no-execute feature on ARMv7 to prevent userspace code execution by the kernel. - AMBA primecell bus handling of irq-safe runtime PM - Unwinding support for memset/memzero/memmove/memcpy functions - VFP fixes for Krait CPUs and improvements in detecting the VFP architecture - A number of code cleanups (using pr_*, removing or reducing the severity of a couple of kernel messages, splitting ftrace asm code out to a separate file, etc.) - Add machine name to stack dump output" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits) ARM: 8247/2: pcmcia: sa1100: make use of device clock ARM: 8246/2: pcmcia: sa1111: provide device clock ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks ARM: 8244/1: fbdev: sa1100fb: make use of device clock ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device ARM: 8242/1: sa1100: add cpu clock ARM: 8221/1: PJ4: allow building in Thumb-2 mode ARM: 8234/1: sa1100: reorder IRQ handling code ARM: 8233/1: sa1100: switch to hwirq usage ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain ARM: 8231/1: sa1100: introduce irqdomains support ARM: 8230/1: sa1100: shift IRQs by one ARM: 8229/1: sa1100: replace irq numbers with names in irq driver ARM: 8228/1: sa1100: drop entry-macro.S ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER ARM: 8241/1: Update processor_modes for hyp and monitor mode ARM: 8240/1: MCPM: document mcpm_sync_init() ARM: 8239/1: Introduce {set,clear}_pte_bit ARM: 8238/1: mm: Refine set_memory_* functions ARM: 8237/1: fix flush_pfn_alias ...

Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2014-12-11T05:17:00Z

Pull ACPI and power management updates from Rafael Wysocki: "This time we have some more new material than we used to have during the last couple of development cycles. The most important part of it to me is the introduction of a unified interface for accessing device properties provided by platform firmware. It works with Device Trees and ACPI in a uniform way and drivers using it need not worry about where the properties come from as long as the platform firmware (either DT or ACPI) makes them available. It covers both devices and "bare" device node objects without struct device representation as that turns out to be necessary in some cases. This has been in the works for quite a few months (and development cycles) and has been approved by all of the relevant maintainers. On top of that, some drivers are switched over to the new interface (at25, leds-gpio, gpio_keys_polled) and some additional changes are made to the core GPIO subsystem to allow device drivers to manipulate GPIOs in the "canonical" way on platforms that provide GPIO information in their ACPI tables, but don't assign names to GPIO lines (in which case the driver needs to do that on the basis of what it knows about the device in question). That also has been approved by the GPIO core maintainers and the rfkill driver is now going to use it. Second is support for hardware P-states in the intel_pstate driver. It uses CPUID to detect whether or not the feature is supported by the processor in which case it will be enabled by default. However, it can be disabled entirely from the kernel command line if necessary. Next is support for a platform firmware interface based on ACPI operation regions used by the PMIC (Power Management Integrated Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms. That interface is used for manipulating power resources and for thermal management: sensor temperature reporting, trip point setting and so on. Also the ACPI core is now going to support the _DEP configuration information in a limited way. Basically, _DEP it supposed to reflect off-the-hierarchy dependencies between devices which may be very indirect, like when AML for one device accesses locations in an operation region handled by another device's driver (usually, the device depended on this way is a serial bus or GPIO controller). The support added this time is sufficient to make the ACPI battery driver work on Asus T100A, but it is general enough to be able to cover some other use cases in the future. Finally, we have a new cpufreq driver for the Loongson1B processor. In addition to the above, there are fixes and cleanups all over the place as usual and a traditional ACPICA update to a recent upstream release. As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for Intel platforms should be able to handle power management of the DMA engine correctly, the cpufreq-dt driver should interact with the thermal subsystem in a better way and the ACPI backlight driver should handle some more corner cases, among other things. On top of the ACPICA update there are fixes for race conditions in the ACPICA's interrupt handling code which might lead to some random and strange looking failures on some systems. In the cleanups department the most visible part is the series of commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration option. That was triggered by a discussion regarding the generic power domains code during which we realized that trying to support certain combinations of PM config options was painful and not really worth it, because nobody would use them in production anyway. For this reason, we decided to make CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the conclusion that the latter became redundant and CONFIG_PM could be used instead of it. The material here makes that replacement in a major part of the tree, but there will be at least one more batch of that in the second part of the merge window. Specifics: - Support for retrieving device properties information from ACPI _DSD device configuration objects and a unified device properties interface for device drivers (and subsystems) on top of that. As stated above, this works with Device Trees and ACPI and allows device drivers to be written in a platform firmware (DT or ACPI) agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are now going to use this new interface and the GPIO subsystem is additionally modified to allow device drivers to assign names to GPIO resources returned by ACPI _CRS objects (in case _DSD is not present or does not provide the expected data). The changes in this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam, Geert Uytterhoeven). - Support for Hardware Managed Performance States (HWP) as described in Volume 3, section 14.4, of the Intel SDM in the intel_pstate driver. CPUID is used to detect whether or not the feature is supported by the processor. If supported, it will be enabled automatically unless the intel_pstate=no_hwp switch is present in the kernel command line. From Dirk Brandewie. - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie). - Support for firmware interface based on ACPI operation regions used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR platforms for power resource control and thermal management (Aaron Lu). - Limited support for retrieving off-the-hierarchy dependencies between devices from ACPI _DEP device configuration objects and deferred probing support for the ACPI battery driver based on the _DEP information to make that driver work on Asus T100A (Lan Tianyu). - New cpufreq driver for the Loongson1B processor (Kelvin Cheung). - ACPICA update to upstream revision 20141107 which only affects tools (Bob Moore). - Fixes for race conditions in the ACPICA's interrupt handling code and in the ACPI code related to system suspend and resume (Lv Zheng and Rafael J Wysocki). - ACPI core fix for an RCU-related issue in the ioremap() regions management code that slowed down significantly after CPUs had been allowed to enter idle states even if they'd had RCU callbakcs queued and triggered some problems in certain proprietary graphics driver (and elsewhere). The fix replaces synchronize_rcu() in that code with synchronize_rcu_expedited() which makes the issue go away. From Konstantin Khlebnikov. - ACPI LPSS (Low-Power Subsystem) driver fix to handle power management of the DMA engine included into the LPSS correctly. The problem is that the DMA engine doesn't have ACPI PM support of its own and it simply is turned off when the last LPSS device having ACPI PM support goes into D3cold. To work around that, the PM domain used by the ACPI LPSS driver is redesigned so at least one device with ACPI PM support will be on as long as the DMA engine is in use. From Andy Shevchenko. - ACPI backlight driver fix to avoid using it on "Win8-compatible" systems where it doesn't work and where it was used by default by mistake (Aaron Lu). - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki, Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin Chaugule (mostly related to the upcoming ARM64 support). - Intel RAPL (Running Average Power Limit) power capping driver fixes and improvements including new processor IDs (Jacob Pan). - Generic power domains modification to power up domains after attaching devices to them to meet the expectations of device drivers and bus types assuming devices to be accessible at probe time (Ulf Hansson). - Preliminary support for controlling device clocks from the generic power domains core code and modifications of the ARM/shmobile platform to use that feature (Ulf Hansson). - Assorted minor fixes and cleanups of the generic power domains core code (Ulf Hansson, Geert Uytterhoeven). - Assorted minor fixes and cleanups of the device clocks control code in the PM core (Geert Uytterhoeven, Grygorii Strashko). - Consolidation of device power management Kconfig options by making CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter which is now redundant (Rafael J Wysocki and Kevin Hilman). That is the first batch of the changes needed for this purpose. - Core device runtime power management support code cleanup related to the execution of callbacks (Andrzej Hajda). - cpuidle ARM support improvements (Lorenzo Pieralisi). - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and Bartlomiej Zolnierkiewicz). - New cpufreq driver callback (->ready) to be executed when the cpufreq core is ready to use a given policy object and cpufreq-dt driver modification to use that callback for cooling device registration (Viresh Kumar). - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James Geboski, Tomeu Vizoso). - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate, cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao, Stefan Wahren, Petr Cvek). - OPP (Operating Performance Points) framework modification to allow OPPs to be removed too and update of a few cpufreq drivers (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added during initialization) on driver removal (Viresh Kumar). - Hibernation core fixes and cleanups (Tina Ruchandani and Markus Elfring). - PM Kconfig fix related to CPU power management (Pankaj Dubey). - cpupower tool fix (Prarit Bhargava)" * tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits) i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM tools: cpupower: fix return checks for sysfs_get_idlestate_count() drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM leds: leds-gpio: Fix multiple instances registration without 'label' property iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM hwrandom / exynos / PM: Use CONFIG_PM in #ifdef block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM USB / PM: Drop CONFIG_PM_RUNTIME from the USB core PM: Merge the SET*_RUNTIME_PM_OPS() macros ...