user/sven/linux.git/drivers/ata, branch v4.4.293

libata: fix read log timeout value

2021-11-26T10:58:33Z

commit 68dbbe7d5b4fde736d104cbbc9a2fce875562012 upstream. Some ATA drives are very slow to respond to READ_LOG_EXT and READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the device is revalidated right after resuming a system or inserting the ATA adapter driver (e.g. ahci). The default 5s timeout (ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing errors during the device configuration. Ex: ... ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209 ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133 ata9.00: qc timeout (cmd 0x2f) ata9.00: Read log page 0x00 failed, Emask 0x4 ata9.00: Read log page 0x00 failed, Emask 0x40 ata9.00: NCQ Send/Recv Log not supported ata9.00: Read log page 0x08 failed, Emask 0x40 ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA ata9.00: Read log page 0x00 failed, Emask 0x40 ata9.00: ATA Identify Device Log not supported ata9.00: failed to set xfermode (err_mask=0x40) ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata9.00: configured for UDMA/133 ... The timeout error causes a soft reset of the drive link, followed in most cases by a successful revalidation as that give enough time to the drive to become fully ready to quickly process the read log commands. However, in some cases, this also fails resulting in the device being dropped. Fix this by using adding the ata_eh_revalidate_timeouts entries for the READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout increased to 15s, retriable one time. Reported-by: Geert Uytterhoeven Tested-by: Geert Uytterhoeven Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal Signed-off-by: Greg Kroah-Hartman

ata: sata_mv: Fix the error handling of mv_chip_id()

2021-11-02T16:38:11Z

commit a0023bb9dd9bc439d44604eeec62426a990054cd upstream. mv_init_host() propagates the value returned by mv_chip_id() which in turn gets propagated by mv_pci_init_one() and hits local_pci_probe(). During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Since this is a bug rather than a recoverable runtime error we should use dev_alert() instead of dev_err(). Signed-off-by: Zheyu Ma Signed-off-by: Damien Le Moal Signed-off-by: Greg Kroah-Hartman

pata_legacy: fix a couple uninitialized variable bugs

2021-10-27T07:32:39Z

commit 013923477cb311293df9079332cf8b806ed0e6f2 upstream. The last byte of "pad" is used without being initialized. Fixes: 55dba3120fbc ("libata: update ->data_xfer hook for ATAPI") Signed-off-by: Dan Carpenter Signed-off-by: Damien Le Moal Signed-off-by: Greg Kroah-Hartman

libata: Add ATA_HORKAGE_NO_NCQ_ON_ATI for Samsung 860 and 870 SSD.

2021-10-09T11:24:30Z

commit 7a8526a5cd51cf5f070310c6c37dd7293334ac49 upstream. Many users are reporting that the Samsung 860 and 870 SSD are having various issues when combined with AMD/ATI (vendor ID 0x1002) SATA controllers and only completely disabling NCQ helps to avoid these issues. Always disabling NCQ for Samsung 860/870 SSDs regardless of the host SATA adapter vendor will cause I/O performance degradation with well behaved adapters. To limit the performance impact to ATI adapters, introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ only for these adapters. Also, two libata.force parameters (noncqati and ncqati) are introduced to disable and enable the NCQ for the system which equipped with ATI SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ function to be enabled or disabled according to the demand. After verifying the chipset from the user reports, the issue appears on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on recent AMD SATA adapters. The vendor ID of ATI should be 0x1002. Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to ATA_HORKAGE_NO_NCQ_ON_ATI. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693 Signed-off-by: Kate Hsuan Reviewed-by: Hans de Goede Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com Reviewed-by: Martin K. Petersen Signed-off-by: Jens Axboe Cc: Krzysztof Olędzki Signed-off-by: Greg Kroah-Hartman

libata: add ATA_HORKAGE_NO_NCQ_TRIM for Samsung 860 and 870 SSDs

2021-09-22T09:41:23Z

commit 8a6430ab9c9c87cb64c512e505e8690bbaee190b upstream. Commit ca6bfcb2f6d9 ("libata: Enable queued TRIM for Samsung SSD 860") limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*", covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*" and "Samsung SSD 850*" series based on information from Samsung. But there is a large number of users which is still reporting issues with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or Marvell SATA controllers and all reporters also report these problems going away when disabling queued trims. Note that with AMD SATA controllers users are reporting even worse issues and only completely disabling NCQ helps there, this will be addressed in a separate patch. Fixes: ca6bfcb2f6d9 ("libata: Enable queued TRIM for Samsung SSD 860") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475 Cc: stable@vger.kernel.org Cc: Kate Hsuan Signed-off-by: Hans de Goede Reviewed-by: Damien Le Moal Reviewed-by: Martin K. Petersen Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com Signed-off-by: Jens Axboe Signed-off-by: Greg Kroah-Hartman

libata: fix ata_host_start()

2021-09-22T09:41:19Z

[ Upstream commit 355a8031dc174450ccad2a61c513ad7222d87a97 ] The loop on entry of ata_host_start() may not initialize host->ops to a non NULL value. The test on the host_stop field of host->ops must then be preceded by a check that host->ops is not NULL. Reported-by: kernel test robot Signed-off-by: Damien Le Moal Reviewed-by: Hannes Reinecke Link: https://lore.kernel.org/r/20210816014456.2191776-3-damien.lemoal@wdc.com Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin

ata: ahci_sunxi: Disable DIPM

2021-07-20T14:22:39Z

commit f6bca4d91b2ea052e917cca3f9d866b5cc1d500a upstream. DIPM is unsupported or broken on sunxi. Trying to enable the power management policy med_power_with_dipm on an Allwinner A20 SoC based board leads to immediate I/O errors and the attached SATA disk disappears from the /dev filesystem. A reset (power cycle) is required to make the SATA controller or disk work again. The A10 and A20 SoC data sheets and manuals don't mention DIPM at all [1], so it's fair to assume that it's simply not supported. But even if it was, it should be considered broken and best be disabled in the ahci_sunxi driver. [1] https://github.com/allwinner-zh/documents/tree/master/ Fixes: c5754b5220f0 ("ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform") Cc: stable@vger.kernel.org Signed-off-by: Timo Sigurdsson Tested-by: Timo Sigurdsson Link: https://lore.kernel.org/r/20210614072539.3307-1-public_timo.s@silentcreek.de Signed-off-by: Jens Axboe Signed-off-by: Greg Kroah-Hartman

pata_ep93xx: fix deferred probing

2021-07-20T14:22:33Z

[ Upstream commit 5c8121262484d99bffb598f39a0df445cecd8efb ] The driver overrides the error codes returned by platform_get_irq() to -ENXIO, so if it returns -EPROBE_DEFER, the driver would fail the probe permanently instead of the deferred probing. Propagate the error code upstream, as it should have been done from the start... Fixes: 2fff27512600 ("PATA host controller driver for ep93xx") Signed-off-by: Sergey Shtylyov Link: https://lore.kernel.org/r/509fda88-2e0d-2cc7-f411-695d7e94b136@omprussia.ru Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin

pata_octeon_cf: avoid WARN_ON() in ata_host_activate()

2021-07-20T14:22:33Z

[ Upstream commit bfc1f378c8953e68ccdbfe0a8c20748427488b80 ] Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler' parameter being non-NULL if the polling mode is selected. Let's only set the pointer to the driver's IRQ handler if platform_get_irq() returns a valid IRQ # -- this should avoid the unnecessary WARN_ON()... Fixes: 43f01da0f279 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.") Signed-off-by: Sergey Shtylyov Link: https://lore.kernel.org/r/3a241167-f84d-1d25-5b9b-be910afbe666@omp.ru Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin

pata_rb532_cf: fix deferred probing

2021-07-20T14:22:33Z

[ Upstream commit 2d3a62fbae8e5badc2342388f65ab2191c209cc0 ] The driver overrides the error codes returned by platform_get_irq() to -ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe permanently instead of the deferred probing. Switch to propagating the error code upstream, still checking/overriding IRQ0 as libata regards it as "no IRQ" (thus polling) anyway... Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Signed-off-by: Sergey Shtylyov Link: https://lore.kernel.org/r/771ced55-3efb-21f5-f21c-b99920aae611@omprussia.ru Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin