user/sven/linux.git/drivers/base/regmap/Makefile, branch v5.3.11

regmap: add i3c bus support

2019-06-07T12:09:55Z

Add basic support for i3c bus. This is a simple implementation that only give support for SDR Read and Write commands. Signed-off-by: Vitor Soares Signed-off-by: Mark Brown

regmap: add SCCB support

2018-07-18T14:45:23Z

This adds Serial Camera Control Bus (SCCB) support for regmap API that is intended to be used by some of Omnivision sensor drivers. The ov772x and ov9650 drivers are going to use this SCCB regmap API. The ov772x driver was previously only worked with the i2c controller drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x device doesn't support repeated starts. After commit 0b964d183cbf ("media: ov772x: allow i2c controllers without I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with issuing two separated i2c messages in order to avoid repeated start. Using this SCCB regmap hides the implementation detail. The ov9650 driver also issues two separated i2c messages to read the registers as the device doesn't support repeated start. So it can make use of this SCCB regmap. Cc: Mark Brown Cc: Peter Rosin Cc: Sebastian Reichel Cc: Wolfram Sang Cc: Sylwester Nawrocki Cc: Jacopo Mondi Cc: Laurent Pinchart Cc: Hans Verkuil Cc: Sakari Ailus Cc: Mauro Carvalho Chehab Signed-off-by: Akinobu Mita Signed-off-by: Mark Brown

Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

2018-02-01T18:31:17Z

Pull char/misc driver updates from Greg KH: "Here is the big pull request for char/misc drivers for 4.16-rc1. There's a lot of stuff in here. Three new driver subsystems were added for various types of hardware busses: - siox - slimbus - soundwire as well as a new vboxguest subsystem for the VirtualBox hypervisor drivers. There's also big updates from the FPGA subsystem, lots of Android binder fixes, the usual handful of hyper-v updates, and lots of other smaller driver updates. All of these have been in linux-next for a long time, with no reported issues" * tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits) char: lp: use true or false for boolean values android: binder: use VM_ALLOC to get vm area android: binder: Use true and false for boolean values lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN EISA: Delete error message for a failed memory allocation in eisa_probe() EISA: Whitespace cleanup misc: remove AVR32 dependencies virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES soundwire: Fix a signedness bug uio_hv_generic: fix new type mismatch warnings uio_hv_generic: fix type mismatch warnings auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE uio_hv_generic: add rescind support uio_hv_generic: check that host supports monitor page uio_hv_generic: create send and receive buffers uio: document uio_hv_generic regions doc: fix documentation about uio_hv_generic vmbus: add monitor_id and subchannel_id to sysfs per channel vmbus: fix ABI documentation uio_hv_generic: use ISR callback method ...

regmap: Add SoundWire bus support

2018-01-08T11:27:18Z

SoundWire bus provides sdw_read() and sdw_write() APIs for Slave devices to program the registers. Provide support in regmap for SoundWire bus. Signed-off-by: Hardik T Shah Signed-off-by: Sanyog Kale Reviewed-by: Philippe Ombredanne Acked-by: Pierre-Louis Bossart Reviewed-by: Takashi Iwai Signed-off-by: Vinod Koul Signed-off-by: Mark Brown

regmap: add SLIMbus support

2017-12-19T10:01:03Z

This patch adds support to read/write SLIMbus value elements. Currently it only supports byte read/write. Adding this support in regmap would give codec drivers more flexibility when there are more than 2 control interfaces like SLIMbus, i2c. Without this patch each codec driver has to directly call SLIMbus value element apis, and this could would get messy once we want to add i2c interface to it. Signed-off-by: Srinivas Kandagatla Reviwed-by: Mark Brown Signed-off-by: Greg Kroah-Hartman

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

Merge branch 'topic/lzo' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-1wire

2017-06-06T19:10:47Z

regmap: Add 1-Wire bus support

2017-06-06T18:47:28Z

Add basic support regmap (register map access) API for 1-Wire bus Signed-off-by: Mark Brown

regmap: make LZO cache optional

2017-06-06T18:46:57Z

Commit 2cbbb579bcbe3 ("regmap: Add the LZO cache support") added support for LZO compression in regcache, but there were never any users added afterwards. Since LZO support itself has its own size, it currently is rather a deoptimization. So make it optional by introducing a symbol that can be selected by drivers wanting to make use of it. Saves e.g. ~46 kB on MIPS (size of LZO support + regcache LZO code). Signed-off-by: Jonas Gorski Signed-off-by: Mark Brown

regmap: Move tracing header into drivers/base/regmap

2015-03-19T22:22:45Z

The tracing events for regmap are confined to the regmap subsystem. It also requires accessing an internal header. Instead of including the internal header from a generic file location, move the tracing file into the regmap directory. Also rename the regmap tracing header to trace.h, as it is redundant to keep the regmap.h name when it is in the regmap directory. Signed-off-by: Steven Rostedt Signed-off-by: Mark Brown