user/sven/linux.git/drivers/bus, branch v6.1.105

bus: mhi: host: pci_generic: add support for Telit FE990 modem

2024-08-14T11:52:49Z

commit 0724869ede9c169429bb622e2d28f97995a95656 upstream. Add support for Telit FE990 that has the same configuration as FN990: $ lspci -vv 04:00.0 Unassigned class [ff00]: Qualcomm Device 0308 Subsystem: Device 1c5d:2015 Signed-off-by: Daniele Palmas Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20230804094039.365102-1-dnlplm@gmail.com [mani: minor update to commit subject and adjusted comment] Signed-off-by: Manivannan Sadhasivam Cc: Fabio Porcedda Signed-off-by: Greg Kroah-Hartman

bus: mhi: host: Add MHI_PM_SYS_ERR_FAIL state

2024-04-13T11:05:16Z

[ Upstream commit bce3f770684cc1d91ff9edab431b71ac991faf29 ] When processing a SYSERR, if the device does not respond to the MHI_RESET from the host, the host will be stuck in a difficult to recover state. The host will remain in MHI_PM_SYS_ERR_PROCESS and not clean up the host channels. Clients will not be notified of the SYSERR via the destruction of their channel devices, which means clients may think that the device is still up. Subsequent SYSERR events such as a device fatal error will not be processed as the state machine cannot transition from PROCESS back to DETECT. The only way to recover from this is to unload the mhi module (wipe the state machine state) or for the mhi controller to initiate SHUTDOWN. This issue was discovered by stress testing soc_reset events on AIC100 via the sysfs node. soc_reset is processed entirely in hardware. When the register write hits the endpoint hardware, it causes the soc to reset without firmware involvement. In stress testing, there is a rare race where soc_reset N will cause the soc to reset and PBL to signal SYSERR (fatal error). If soc_reset N+1 is triggered before PBL can process the MHI_RESET from the host, then the soc will reset again, and re-run PBL from the beginning. This will cause PBL to lose all state. PBL will be waiting for the host to respond to the new syserr, but host will be stuck expecting the previous MHI_RESET to be processed. Additionally, the AMSS EE firmware (QSM) was hacked to synthetically reproduce the issue by simulating a FW hang after the QSM issued a SYSERR. In this case, soc_reset would not recover the device. For this failure case, to recover the device, we need a state similar to PROCESS, but can transition to DETECT. There is not a viable existing state to use. POR has the needed transitions, but assumes the device is in a good state and could allow the host to attempt to use the device. Allowing PROCESS to transition to DETECT invites the possibility of parallel SYSERR processing which could get the host and device out of sync. Thus, invent a new state - MHI_PM_SYS_ERR_FAIL This essentially a holding state. It allows us to clean up the host elements that are based on the old state of the device (channels), but does not allow us to directly advance back to an operational state. It does allow the detection and processing of another SYSERR which may recover the device, or allows the controller to do a clean shutdown. Signed-off-by: Jeffrey Hugo Reviewed-by: Carl Vanderlip Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20240112180800.536733-1-quic_jhugo@quicinc.com Signed-off-by: Manivannan Sadhasivam Signed-off-by: Sasha Levin

bus: tegra-aconnect: Update dependency to ARCH_TEGRA

2024-03-26T22:20:36Z

[ Upstream commit 4acd21a45c1446277e2abaece97d7fa7c2e692a9 ] Update the architecture dependency to be the generic Tegra because the driver works on the four latest Tegra generations not just Tegra210, if you build a kernel with a specific ARCH_TEGRA_xxx_SOC option that excludes Tegra210 you don't get this driver. Fixes: 46a88534afb59 ("bus: Add support for Tegra ACONNECT") Signed-off-by: Peter Robinson Cc: Jon Hunter Cc: Thierry Reding Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin

bus: moxtet: Add spi device table

2024-02-23T08:12:48Z

[ Upstream commit aaafe88d5500ba18b33be72458439367ef878788 ] The moxtet module fails to auto-load on. Add a SPI id table to allow it to do so. Signed-off-by: Sjoerd Simons Cc: Reviewed-by: Marek Behún Signed-off-by: Gregory CLEMENT Signed-off-by: Sasha Levin

bus: mhi: ep: Do not allocate event ring element on stack

2024-02-01T00:17:09Z

[ Upstream commit 987fdb5a43a66764808371b54e6047834170d565 ] It is possible that the host controller driver would use DMA framework to write the event ring element. So avoid allocating event ring element on the stack as DMA cannot work on vmalloc memory. Cc: stable@vger.kernel.org Fixes: 961aeb689224 ("bus: mhi: ep: Add support for sending events to the host") Link: https://lore.kernel.org/r/20230901073502.69385-1-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam Signed-off-by: Sasha Levin

bus: mhi: host: Add spinlock to protect WP access when queueing TREs

2024-02-01T00:16:59Z

commit b89b6a863dd53bc70d8e52d50f9cfaef8ef5e9c9 upstream. Protect WP accesses such that multiple threads queueing buffers for incoming data do not race. Meanwhile, if CONFIG_TRACE_IRQFLAGS is enabled, irq will be enabled once __local_bh_enable_ip is called as part of write_unlock_bh. Hence, let's take irqsave lock after TRE is generated to avoid running write_unlock_bh when irqsave lock is held. Cc: stable@vger.kernel.org Fixes: 189ff97cca53 ("bus: mhi: core: Add support for data transfer") Signed-off-by: Bhaumik Bhatt Signed-off-by: Qiang Yu Reviewed-by: Jeffrey Hugo Tested-by: Jeffrey Hugo Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/1702276972-41296-2-git-send-email-quic_qianyu@quicinc.com Signed-off-by: Manivannan Sadhasivam Signed-off-by: Greg Kroah-Hartman

bus: mhi: host: Drop chan lock before queuing buffers

2024-02-01T00:16:59Z

commit 01bd694ac2f682fb8017e16148b928482bc8fa4b upstream. Ensure read and write locks for the channel are not taken in succession by dropping the read lock from parse_xfer_event() such that a callback given to client can potentially queue buffers and acquire the write lock in that process. Any queueing of buffers should be done without channel read lock acquired as it can result in multiple locks and a soft lockup. Cc: # 5.7 Fixes: 1d3173a3bae7 ("bus: mhi: core: Add support for processing events from client device") Signed-off-by: Qiang Yu Reviewed-by: Jeffrey Hugo Tested-by: Jeffrey Hugo Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/1702276972-41296-3-git-send-email-quic_qianyu@quicinc.com [mani: added fixes tag and cc'ed stable] Signed-off-by: Manivannan Sadhasivam Signed-off-by: Greg Kroah-Hartman

bus: mhi: host: Add alignment check for event ring read pointer

2024-02-01T00:16:59Z

commit eff9704f5332a13b08fbdbe0f84059c9e7051d5f upstream. Though we do check the event ring read pointer by "is_valid_ring_ptr" to make sure it is in the buffer range, but there is another risk the pointer may be not aligned. Since we are expecting event ring elements are 128 bits(struct mhi_ring_element) aligned, an unaligned read pointer could lead to multiple issues like DoS or ring buffer memory corruption. So add a alignment check for event ring read pointer. Fixes: ec32332df764 ("bus: mhi: core: Sanity check values from remote device before use") cc: stable@vger.kernel.org Signed-off-by: Krishna chaitanya chundru Reviewed-by: Jeffrey Hugo Reviewed-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20231031-alignment_check-v2-1-1441db7c5efd@quicinc.com Signed-off-by: Manivannan Sadhasivam Signed-off-by: Greg Kroah-Hartman

bus: ti-sysc: Flush posted write only after srst_udelay

2024-01-01T12:39:07Z

commit f71f6ff8c1f682a1cae4e8d7bdeed9d7f76b8f75 upstream. Commit 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before reset") caused a regression reproducable on omap4 duovero where the ISS target module can produce interconnect errors on boot. Turns out the registers are not accessible until after a delay for devices needing a ti,sysc-delay-us value. Let's fix this by flushing the posted write only after the reset delay. We do flushing also for ti,sysc-delay-us using devices as that should trigger an interconnect error if the delay is not properly configured. Let's also add some comments while at it. Fixes: 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before reset") Cc: stable@vger.kernel.org Signed-off-by: Tony Lindgren Signed-off-by: Greg Kroah-Hartman

bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up

2023-10-06T12:56:48Z

[ Upstream commit e5deb8f76e64d94ccef715e75ebafffd0c312d80 ] The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE is used to force idle target modules rather than block idle during usage. The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when a target module is active, and configure autoidle and wake-up when a target module is inactive. We are missing configuring the target module on sysc_disable_module(), and missing toggling of the wake-up bit. Let's fix the issue to allow uart wake-up to work. Fixes: fb685f1c190e ("bus: ti-sysc: Handle swsup idle mode quirks") Tested-by: Dhruva Gole Tested-by: Kevin Hilman Signed-off-by: Tony Lindgren Signed-off-by: Sasha Levin