user/sven/linux.git/drivers/clocksource/Makefile, branch v4.15.11

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

clocksource/drivers/imx-tpm: Add imx tpm timer support

2017-08-29T09:07:56Z

IMX Timer/PWM Module (TPM) supports both timer and pwm function while this patch only adds the timer support. PWM would be added later. The TPM counter, compare and capture registers are clocked by an asynchronous clock that can remain enabled in low power modes. NOTE: We observed in a very small probability, the bus fabric contention between GPU and A7 may results a few cycles delay of writing CNT registers which may cause the min_delta event got missed, so we need add a ETIME check here in case it happened. Cc: Daniel Lezcano Cc: Arnd Bergmann Cc: Thomas Gleixner Cc: Shawn Guo Cc: Anson Huang Cc: Bai Ping Signed-off-by: Dong Aisheng Signed-off-by: Daniel Lezcano

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2017-07-04T21:47:47Z

Pull ARM SoC driver updates from Arnd Bergmann: "New SoC specific drivers: - NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later) based on the "BPMP" firmware - Clocksource and system controller drivers for the newly added Action Semi platforms (both arm and arm64). Reset subsystem, merged through arm-soc by tradition: - New drivers for Altera Stratix10, TI Keystone and Cortina Gemini SoCs - Various subsystem-wide cleanups Updates for existing SoC-specific drivers - TI GPMC (General Purpose Memory Controller) - Mediatek "scpsys" system controller support for MT6797 - Broadcom "brcmstb_gisb" bus arbitrer - ARM SCPI firmware - Renesas "SYSC" system controller One more driver update was submitted for the Freescale/NXP DPAA data path acceleration that has previously been used on PowerPC chips. I ended up postponing the merge until some API questions for its unusual MMIO access are resolved" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits) clocksource: owl: Add S900 support clocksource: Add Owl timer soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON firmware: tegra: Fix locking bugs in BPMP soc/tegra: flowctrl: Fix error handling soc/tegra: bpmp: Implement generic PM domains soc/tegra: bpmp: Update ABI header PM / Domains: Allow overriding the ->xlate() callback soc: brcmstb: enable drivers for ARM64 and BMIPS soc: renesas: Rework Kconfig and Makefile logic reset: Add the TI SCI reset driver dt-bindings: reset: Add TI SCI reset binding reset: use kref for reference counting soc: qcom: smsm: Improve error handling, quiesce probe deferral cpufreq: scpi: use new scpi_ops functions to remove duplicate code firmware: arm_scpi: add support to populate OPPs and get transition latency dt-bindings: reset: Add reset manager offsets for Stratix10 memory: omap-gpmc: add error message if bank-width property is absent memory: omap-gpmc: make dts snippet include semicolon reset: Add a Gemini reset controller ...

clocksource: Add Owl timer

2017-06-18T19:19:48Z

The Actions Semi S500 SoC provides four timers, 2Hz0/1 and 32-bit TIMER0/1. Use TIMER0 as clocksource and TIMER1 as clockevents. Based on LeMaker linux-actions tree. An S500 datasheet can be found on the LeMaker Guitar pages: http://www.lemaker.org/product-guitar-download-29.html Acked-by: Daniel Lezcano Signed-off-by: Andreas Färber

clocksource/drivers: Add timer-of common init routine

2017-06-14T10:02:32Z

The different drivers are all using the same pattern when initializing. 1. Get the base address 2. Get the irq number 3. Get the clock 4. Prepare and enable the clock 5. Get the rate 6. Request an interrupt Instead of repeating again and again these steps in all the drivers, let's provide a common init routine to give the opportunity to factor all of them out. We can expect a significant kernel size improvement when the common routine will be used in all the drivers. Signed-off-by: Daniel Lezcano

clocksource/drivers: Rename CLKSRC_OF to TIMER_OF

2017-06-14T10:01:03Z

The config option name is now renamed to 'TIMER_OF' for consistency with the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change. Signed-off-by: Daniel Lezcano Reviewed-by: Linus Walleij

Revert "clockevents: Add a clkevt-of mechanism like clksrc-of"

2017-06-12T08:54:47Z

After discussing it, this feature is dropped as it is not considered adequate: https://patchwork.kernel.org/patch/9639317/ There is no user of this macro yet, so there is no impact on the drivers. This reverts commit 376bc27150f180d9f5eddec6a14117780177589d. Cc: Mark Rutland Signed-off-by: Daniel Lezcano

clocksource/drivers/fttmr010: Merge Moxa into FTTMR010

2017-06-12T08:45:10Z

This merges the Moxa Art timer driver into the Faraday FTTMR010 driver and replaces all Kconfig symbols to use the Faraday driver instead. We are now so similar that the drivers can be merged by just adding a few lines to the Faraday timer. Differences: - The Faraday driver explicitly sets the counter to count upwards for the clocksource, removing the need for the clocksource core to invert the value. - The Faraday driver also handles sched_clock() On the Aspeed, the counter can only count downwards, so support the timers in downward-counting mode as well, and flag the Aspeed to use this mode. This mode was tested on the Gemini so I have high hopes that it'll work fine on the Aspeed as well. After this we have one driver for all three SoCs and a generic Faraday FTTMR010 timer driver, which is nice. Cc: Joel Stanley Cc: Jonas Jensen Signed-off-by: Linus Walleij Reviewed-by: Joel Stanley Tested-by: Joel Stanley Signed-off-by: Daniel Lezcano

clocksource/drivers/gemini: Rename Gemini timer to Faraday

2017-04-07T14:23:08Z

After some research it turns out that the "Gemini" timer is actually a generic IP block from Faraday Technology named FTTMR010, so as to not make things too confusing we need to rename the driver and its symbols to make sense. The implementation remains the same in this patch but we fix the copy-paste error in the timer name "nomadik_mtu" as we're at it. Signed-off-by: Linus Walleij Signed-off-by: Daniel Lezcano

clocksource/drivers/ostm: Add renesas-ostm timer driver

2017-02-07T19:58:30Z

This patch adds a OSTM driver for the Renesas architecture. The OS Timer (OSTM) has independent channels that can be used as a freerun or interval times. This driver uses the first probed device as a clocksource and then any additional devices as clock events. Signed-off-by: Chris Brandt Signed-off-by: Daniel Lezcano