user/sven/linux.git/drivers/ide/cmd64x.c, branch v3.16.67

Drivers: ide: remove __dev* attributes.

2013-01-03T23:57:03Z

CONFIG_HOTPLUG is going away as an option. As a result, the __dev* markings need to be removed. This change removes the use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit from these drivers. Based on patches originally written by Bill Pemberton, but redone by me in order to handle some of the coding style issues better, by hand. Cc: Bill Pemberton Cc: "David S. Miller" Signed-off-by: Greg Kroah-Hartman

sections: fix section conflicts in drivers/ide

2012-10-05T18:04:41Z

Signed-off-by: Andi Kleen Cc: David Miller Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

cmd64x: fix handling of address setup timings

2010-01-19T09:52:32Z

Account for the requirements of the DMA mode currently used. Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller

ide: change ->set_dma_mode method parameters

2010-01-19T09:45:29Z

Change ->set_dma_mode method parameters to match ->set_dmamode method used in struct ata_port_operations. Signed-off-by: Bartlomiej Zolnierkiewicz

ide: change ->set_pio_mode method parameters

2010-01-19T09:44:41Z

Change ->set_pio_mode method parameters to match ->set_piomode method used in struct ata_port_operations. Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller

cmd64x: remove superfluous checks from cmd64x_set_dma_mode()

2010-01-19T09:24:59Z

Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller

cmd64x: fix PIO and MWDMA timings calculations

2010-01-19T09:24:58Z

Just use the standard ide_timing_compute() helper to calculate PIO and MWDMA timings. This fixes some issues with the open-coded version like allowing faster MWDMA timings than the ones required by the current PIO mode or not accounting for the enhanced MWDMA cycle time specified by the device. Based on libata pata_cmd64x host driver. Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller

cmd64x: remove no longer needed debugging code

2009-12-03T16:25:57Z

Signed-off-by: Bartlomiej Zolnierkiewicz

ide: Serialize CMD643 and CMD646 to fix a hardware bug with SSD

2009-10-29T10:02:06Z

CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is connected to one of the channels. Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3. /dev/hda is 8GB Seagate ST38410A in MWDMA2 /dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2 - When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda are corrupted, there are twiddled single bits 1->0 and some full 32-bit words corrupted, sometimes commands fail (which switches /dev/hda to PIO mode but the corruptions happen even in PIO). - Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine). - When I connected normal rotating harddisk to /dev/hdd, there was no corruption, so the corruption is something specific to SSD. - I tried the same setup on a PCI card with CMD649 and saw no corruption. This patch serializes the operation for CMD646 and 643 (I didn't test CMD643 but it may have the same hw bug too because it's earlier design). CMD649 is good. I don't know anything about CMD 648. Signed-off-by: Mikulas Patocka Tested-by: Frans Pop Signed-off-by: David S. Miller

ide cmd64x: Remove serialize setting.

2009-06-22T05:48:03Z

This begins to fix regressions reported by Frans Pop on his Ultra-10. There are still some funnies left that we are investigating. Signed-off-by: David S. Miller