user/sven/linux.git/drivers/input/mouse/synaptics.c, branch v3.2.60

Input: synaptics - add min/max quirk for ThinkPad Edge E431

2014-06-09T12:29:01Z

commit 27a38856a948c3e8de30dc71647ff9e1778c99fc upstream. Signed-off-by: Hans de Goede Signed-off-by: Dmitry Torokhov Signed-off-by: Ben Hutchings

Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1

2014-05-18T13:58:06Z

commit 46a2986ebbe18757c2d8c352f8fb6e0f4f0754e3 upstream. We expect that all the Haswell series will need such quirks, sigh. The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad, with the same min/max issue. The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation. The X1 and T431s share a PnPID with the T540p, but the reported ranges are closer to those of the T440s. HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me, S1 Yoga and X1 are written by Benjamin Tissoires. Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the X240, X1 uses the same touchpad as the T440. Signed-off-by: Benjamin Tissoires Signed-off-by: Hans de Goede Signed-off-by: Dmitry Torokhov Signed-off-by: Ben Hutchings

Input: synaptics - add manual min/max quirk for ThinkPad X240

2014-04-09T01:20:44Z

commit 8a0435d958fb36d93b8df610124a0e91e5675c82 upstream. This extends Benjamin Tissoires manual min/max quirk table with support for the ThinkPad X240. Signed-off-by: Hans de Goede Signed-off-by: Dmitry Torokhov Signed-off-by: Ben Hutchings

Input: synaptics - add manual min/max quirk

2014-04-09T01:20:44Z

commit 421e08c41fda1f0c2ff6af81a67b491389b653a5 upstream. The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad. However, these new Synaptics devices report bad axis ranges. Under Windows, it is not a problem because the Windows driver uses RMI4 over SMBus to talk to the device. Under Linux, we are using the PS/2 fallback interface and it occurs the reported ranges are wrong. Of course, it would be too easy to have only one range for the whole series, each touchpad seems to be calibrated in a different way. We can not use SMBus to get the actual range because I suspect the firmware will switch into the SMBus mode and stop talking through PS/2 (this is the case for hybrid HID over I2C / PS/2 Synaptics touchpads). So as a temporary solution (until RMI4 land into upstream), start a new list of quirks with the min/max manually set. Signed-off-by: Benjamin Tissoires Signed-off-by: Dmitry Torokhov Signed-off-by: Ben Hutchings

Input: synaptics - adjust threshold for treating position values as negative

2012-10-17T02:49:11Z

commit 824efd37415961d38821ecbd9694e213fb2e8b32 upstream. Commit c039450 (Input: synaptics - handle out of bounds values from the hardware) caused any hardware reported values over 7167 to be treated as a wrapped-around negative value. It turns out that some firmware uses the value 8176 to indicate a finger near the edge of the touchpad whose actual position cannot be determined. This value now gets treated as negative, which can cause pointer jumps and broken edge scrolling on these machines. I only know of one touchpad which reports negative values, and this hardware never reports any value lower than -8 (i.e. 8184). Moving the threshold for treating a value as negative up to 8176 should work fine then for any hardware we currently know about, and since we're dealing with unspecified behavior it's probably the best we can do. The special 8176 value is also likely to result in sudden jumps in position, so let's also clamp this to the maximum specified value for the axis. BugLink: http://bugs.launchpad.net/bugs/1046512 https://bugzilla.kernel.org/show_bug.cgi?id=46371 Signed-off-by: Seth Forshee Reviewed-by: Daniel Kurtz Tested-by: Alan Swanson Tested-by: Arteom Signed-off-by: Dmitry Torokhov Signed-off-by: Ben Hutchings

Input: synaptics - handle out of bounds values from the hardware

2012-08-09T23:24:51Z

commit c0394506e69b37c47d391c2a7bbea3ea236d8ec8 upstream. The touchpad on the Acer Aspire One D250 will report out of range values in the extreme lower portion of the touchpad. These appear as abrupt changes in the values reported by the hardware from very low values to very high values, which can cause unexpected vertical jumps in the position of the mouse pointer. What seems to be happening is that the value is wrapping to a two's compliment negative value of higher resolution than the 13-bit value reported by the hardware, with the high-order bits being truncated. This patch adds handling for these values by converting them to the appropriate negative values. The only tricky part about this is deciding when to treat a number as negative. It stands to reason that if out of range values can be reported on the low end then it could also happen on the high end, so not all out of range values should be treated as negative. The approach taken here is to split the difference between the maximum legitimate value for the axis and the maximum possible value that the hardware can report, treating values greater than this number as negative and all other values as positive. This can be tweaked later if hardware is found that operates outside of these parameters. BugLink: http://bugs.launchpad.net/bugs/1001251 Signed-off-by: Seth Forshee Reviewed-by: Daniel Kurtz Signed-off-by: Dmitry Torokhov [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

Input: synaptics - fix touchpad not working after S2R on Vostro V13

2011-12-12T08:06:56Z

Synaptics touchpads on several Dell laptops, particularly Vostro V13 systems, may not respond properly to PS/2 commands and queries immediately after resuming from suspend to RAM. This leads to unresponsive touchpad after suspend/resume cycle. Adding a 1-second delay after resetting the device allows touchpad to finish initializing (calibrating?) and start reacting properly. Reported-by: Daniel Manrique Tested-by: Daniel Manrique Cc: stable@kernel.org Signed-off-by: Dmitry Torokhov

Input: psmouse - switch to using dev_*() for messages

2011-10-11T01:28:16Z

This will ensure our reporting is consistent with the rest of the system and we do not refer to obsolete source file names. Reviewed-by: Wanlong Gao Reviewed-by: JJ Ding Reviewed-by: Daniel Kurtz Signed-off-by: Dmitry Torokhov

Input: synaptics - process finger (<=5) transitions

2011-08-24T06:08:32Z

Synaptics image sensor touchpads track up to 5 fingers, but only report 2. They use a special "TYPE=2" (AGM-CONTACT) packet type that reports the number of tracked fingers and which finger is reported in the SGM and AGM packets. With this new packet type, it is possible to tell userspace when 4 or 5 fingers are touching. Signed-off-by: Daniel Kurtz Acked-by: Chase Douglas Acked-by: Henrik Rydberg Signed-off-by: Dmitry Torokhov

Input: synaptics - process finger (<=3) transitions

2011-08-24T06:08:24Z

Synaptics image sensor touchpads track 5 fingers, but only report 2. This patch attempts to deal with some idiosyncrasies of these touchpads: * When there are 3 or more fingers, only two are reported. * The touchpad tracks the 5 fingers in slot[0] through slot[4]. * It always reports the lowest and highest valid slots in SGM and AGM packets, respectively. * The number of fingers is only reported in the SGM packet. However, the number of fingers can change either before or after an AGM packet. * Thus, if an SGM reports a different number of fingers than the last SGM, it is impossible to tell whether the intervening AGM corresponds to the old number of fingers or the new number of fingers. * For example, when going from 2->3 fingers, it is not possible to tell whether tell AGM contains slot[1] (old 2nd finger) or slot[2] (new 3rd finger). * When fingers are added one at at time, from 1->2->3, it is possible to track which slots are contained in the SGM and AGM packets: 1 finger: SGM = slot[0], no AGM 2 fingers: SGM = slot[0], AGM = slot[1] 3 fingers: SGM = slot[0], AGM = slot[2] * It is also possible to track which slot is contained in the SGM when 1 of 2 fingers is removed. This is because the touchpad sends a special (0,0,0) AGM packet whenever all fingers are removed except slot[0]: Last AGM == (0,0,0): SGM contains slot[1] Else: SGM contains slot[0] * However, once there are 3 fingers, if exactly 1 finger is removed, it is impossible to tell which 2 slots are contained in SGM and AGM. The (SGM,AGM) could be (0,1), (0,2), or (1,2). There is no way to know. * Similarly, if two fingers are simultaneously removed (3->1), then it is only possible to know if SGM still contains slot[0]. * Since it is not possible to reliably track which slot is being reported, we invalidate the tracking_id every time the number of fingers changes until this ambiguity is resolved when: a) All fingers are removed. b) 4 or 5 fingers are touched, generates an AGM-CONTACT packet. c) All fingers are removed except slot[0]. In this special case, the ambiguity is resolved since by the (0,0,0) AGM packet. Behavior of the driver: When 2 or more fingers are present on the touchpad, the kernel reports up to two MT-B slots containing the position data for two of the fingers reported by the touchpad. If the identity of a finger cannot be tracked when the number-of-fingers changes, the corresponding MT-B slot will be invalidated (track_id set to -1), and a new track_id will be assigned in a subsequent input event report. The driver always reports the total number of fingers using one of the EV_KEY/BTN_TOOL_*TAP events. This could differ from the number of valid MT-B slots for two reasons: a) There are more than 2 fingers on the pad. b) During ambiguous number-of-fingers transitions, the correct track_id for one or both of the slots cannot be determined, so the slots are invalidated. Thus, this is a hybrid singletouch/MT-B scheme. Userspace can detect this behavior by noting that the driver supports more EV_KEY/BTN_TOOL_*TAP events than its maximum EV_ABS/ABS_MT_SLOT. Signed-off-by: Daniel Kurtz Acked-by: Chase Douglas Acked-by: Henrik Rydberg Signed-off-by: Dmitry Torokhov