user/sven/linux.git/drivers/input/tablet/wacom_sys.c, branch v3.4.7

Input: wacom - check for allocation failure in probe()

2012-03-30T05:42:19Z

We accidentally removed the check for NULL in 3aac0ef10b "Input: wacom - isolate input registration". Signed-off-by: Dan Carpenter Reviewed-by: Chris Bagwell Signed-off-by: Dmitry Torokhov

Input: wacom - wireless battery status

2012-03-26T06:33:17Z

Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - create inputs when wireless connect

2012-03-26T06:32:59Z

When a tablet connect or disconnect is detected, schedule work queue to register or unregister related input devices. When a wireless tablet connects, it reports same USB PID used if tablet is connected with USB cable. Use this to update features values, set input capabilities, and then register device. From there, the Pen and Touch interfaces will reuse the existing tablet's IRQ routines. Its possible that 1 receiver is shared with 2 tablets with different PID (small and medium Bamboo for example) so the input is unregister at disconnect to better support this case. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - wireless monitor framework

2012-03-26T06:31:32Z

The 3rd gen Bamboo Pen & Touch and Intuos5 tablets support an optional wireless module. When its receiver is plugged into USB, it presents 3 interfaces: 0) Monitor 1) Pen and 2) Touch. The exact capabilities of the Pen and Touch interfaces can not be determined until a tablet connection is established and reported over the Monitor interface. This patch detects this wireless receiver and enables interrupt packets to be processed for the Monitor interface. Processing the data in packets will be left to another patch. Since it doesn't make sense to create an input device for the Monitor interface, it is not created. Creation of Pen and Touch input device is also delayed until monitor packets can be processed. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Input: wacom - isolate input registration

2012-03-26T06:31:27Z

Although this better co-locates input registration logic, the main goal is to make it easier to optionally create input devices or delay creation to later time periods. Signed-off-by: Chris Bagwell Tested-by: Jason Gerecke Acked-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Merge commit 'v3.3-rc6' into next

2012-03-09T18:55:17Z

Input: wacom - use BTN_TOOL_FINGER to indicate touch device type

2012-01-31T08:14:13Z

Tested-by: Chris Bagwell Reviewed-by: Chris Bagwell Signed-off-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2012-01-10T18:55:52Z

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits) Input: tc3589x-keypad - add missing kerneldoc Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages Input: ucb1400_ts - convert to threaded IRQ Input: ucb1400_ts - drop inline annotations Input: usb1400_ts - add __devinit/__devexit section annotations Input: ucb1400_ts - set driver owner Input: ucb1400_ts - convert to use dev_pm_ops Input: psmouse - make sure we do not use stale methods Input: evdev - do not block waiting for an event if fd is nonblock Input: evdev - if no events and non-block, return EAGAIN not 0 Input: evdev - only allow reading events if a full packet is present Input: add driver for pixcir i2c touchscreens Input: samsung-keypad - implement runtime power management support Input: tegra-kbc - report wakeup key for some platforms Input: tegra-kbc - add device tree bindings Input: add driver for AUO In-Cell touchscreens using pixcir ICs Input: mpu3050 - configure the sampling method Input: mpu3050 - ensure we enable interrupts Input: mpu3050 - add of_match table for device-tree probing Input: sentelic - document the latest hardware ... Fix up fairly trivial conflicts (device tree matching conflicting with some independent cleanups) in drivers/input/keyboard/samsung-keypad.c

Input: wacom - add LED support for Cintiq 24HD

2011-12-12T08:14:21Z

The Cintiq 24HD has three LEDs on the left side of the tablet and three LEDs on the right side of the tablet. Switching to LED 0, 1, or 2 will enable the top, middle, or bottom LED for the respective side. Switching to LED 3 turns off the LEDs on the respective side. Signed-off-by: Jason Gerecke Reviewed-by: Ping Cheng Signed-off-by: Dmitry Torokhov

Merge commit 'v3.2-rc3' into next

2011-11-29T09:51:07Z