user/sven/linux.git/drivers/input/touchscreen/zinitix.c, branch v5.15.141

Input: zinitix - do not report shadow fingers

2022-04-08T12:22:47Z

[ Upstream commit e941dc13fd3717122207d74539ab95da07ef797f ] I observed the following problem with the BT404 touch pad running the Phosh UI: When e.g. typing on the virtual keyboard pressing "g" would produce "ggg". After some analysis it turns out the firmware reports that three fingers hit that coordinate at the same time, finger 0, 2 and 4 (of the five available 0,1,2,3,4). DOWN Zinitix-TS 3-0020: finger 0 down (246, 395) Zinitix-TS 3-0020: finger 1 up (0, 0) Zinitix-TS 3-0020: finger 2 down (246, 395) Zinitix-TS 3-0020: finger 3 up (0, 0) Zinitix-TS 3-0020: finger 4 down (246, 395) UP Zinitix-TS 3-0020: finger 0 up (246, 395) Zinitix-TS 3-0020: finger 2 up (246, 395) Zinitix-TS 3-0020: finger 4 up (246, 395) This is one touch and release: i.e. this is all reported on touch (down) and release. There is a field in the struct touch_event called finger_cnt which is actually a bitmask of the fingers active in the event. Rename this field finger_mask as this matches the use contents better, then use for_each_set_bit() to iterate over just the fingers that are actally active. Factor out a finger reporting function zinitix_report_fingers() to handle all fingers. Also be more careful in reporting finger down/up: we were reporting every event with input_mt_report_slot_state(..., true); but this should only be reported on finger down or move, not on finger up, so also add code to check p->sub_status to see what is happening and report correctly. After this my Zinitix BT404 touchscreen report fingers flawlessly. The vendor drive I have notably does not use the "finger_cnt" and contains obviously incorrect code like this: if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM) touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM; As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is a bitmask this seems quite confused. Signed-off-by: Linus Walleij Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin

Input: zinitix - make sure the IRQ is allocated before it gets enabled

2022-01-11T14:35:19Z

[ Upstream commit cf73ed894ee939d6706d65e0cd186e4a64e3af6d ] Since irq request is the last thing in the driver probe, it happens later than the input device registration. This means that there is a small time window where if the open method is called the driver will attempt to enable not yet available irq. Fix that by moving the irq request before the input device registration. Reviewed-by: Linus Walleij Fixes: 26822652c85e ("Input: add zinitix touchscreen driver") Signed-off-by: Nikita Travkin Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin

Input: move to use request_irq by IRQF_NO_AUTOEN flag

2021-03-25T22:27:56Z

disable_irq() after request_irq() still has a time gap in which interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable because of requesting. On the other hand, request_irq() after setting IRQ_NOAUTOEN as below irq_set_status_flags(irq, IRQ_NOAUTOEN); request_irq(dev, irq...); can also be replaced by request_irq() with IRQF_NO_AUTOEN flag. Signed-off-by: Barry Song Link: https://lore.kernel.org/r/20210302224916.13980-3-song.bao.hua@hisilicon.com Signed-off-by: Dmitry Torokhov

Input: zinitix - fix return type of zinitix_init_touch()

2021-02-19T19:02:42Z

zinitix_init_touch() returns error code or 0 for success and therefore return type must be int, not bool. Fixes: 26822652c85e ("Input: add zinitix touchscreen driver") Reported-by: kernel test robot Reported-by: Jiapeng Chong Link: https://lore.kernel.org/r/YC8z2bXc3Oy8pABa@google.com Signed-off-by: Dmitry Torokhov

Input: zinitix - remove unneeded semicolon

2021-02-16T21:05:54Z

Eliminate the following coccicheck warning: ./drivers/input/touchscreen/zinitix.c:164:31-32: Unneeded semicolon Reported-by: Abaci Robot Signed-off-by: Yang Li Link: https://lore.kernel.org/r/1612319443-115831-1-git-send-email-yang.lee@linux.alibaba.com Signed-off-by: Dmitry Torokhov

Input: use input_device_enabled()

2020-12-03T06:10:33Z

Use the newly added helper in relevant input drivers. Signed-off-by: Andrzej Pietrasiewicz Link: https://lore.kernel.org/r/20200608112211.12125-3-andrzej.p@collabora.com Signed-off-by: Dmitry Torokhov

Input: add zinitix touchscreen driver

2020-10-04T23:08:09Z

Add support for the bt541 touchscreen IC from zinitix, loosely based on downstream driver. The driver currently supports multitouch (5 touch points). The bt541 seems to support touch keys, but the support was not added because that functionality is not being utilized by the touchscreen used for testing. Based on the similartities between downstream drivers, it seems likely that other similar touchscreen ICs can be supported with this driver in the future. Signed-off-by: Michael Srba Link: https://lore.kernel.org/r/20201001122949.16846-1-michael.srba@seznam.cz Signed-off-by: Dmitry Torokhov