user/sven/linux.git/drivers/memory/Makefile, branch v4.14

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

memory: davinci: add support for da8xx DDR2/mDDR controller

2016-11-14T11:48:34Z

Create a new driver for the da8xx DDR2/mDDR controller and implement support for writing to the Peripheral Bus Burst Priority Register. Reviewed-by: Kevin Hilman Acked-by: Rob Herring Signed-off-by: Bartosz Golaszewski [nsekhar@ti.com: subject line adjustment] Signed-off-by: Sekhar Nori

memory: add Atmel EBI (External Bus Interface) driver

2016-06-02T06:32:25Z

The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon Signed-off-by: Alexandre Belloni

memory: Add support for Exynos SROM driver

2016-04-18T12:25:27Z

This patch adds Exynos SROM controller driver which will handle save restore of SROM registers during S2R. Signed-off-by: Pankaj Dubey Reviewed-by: Krzysztof Kozlowski [p.fedin@samsung.com: tested on SMDK5410] Tested-by: Pavel Fedin Signed-off-by: Kukjin Kim [k.kozlowski: Minor COMPILE_TEST adjustments in Kconfig entries] Signed-off-by: Krzysztof Kozlowski

memory: mediatek: Add SMI driver

2016-02-25T15:49:08Z

This patch add SMI(Smart Multimedia Interface) driver. This driver is responsible to enable/disable iommu and control the power domain and clocks of each local arbiter. Signed-off-by: Yong Wu Tested-by: Philipp Zabel Reviewed-by: Daniel Kurtz Tested-by: Daniel Kurtz Signed-off-by: Matthias Brugger Signed-off-by: Joerg Roedel

memory: add ARM PL172 MultiPort Memory Controller driver

2015-07-17T17:43:44Z

This driver makes it possible to configure the static memory chip selects on the ARM PL172 MultiPort Memory Controller from a set of properties in DT. Configuration of dynamic memory is not supported and is left to the boot loader. The intended usage is to setup timing and configuration for static memory devices like NAND and NOR Flash before they are probed by a driver. Signed-off-by: Joachim Eastwood Signed-off-by: Olof Johansson

memory: jz4780-nemc: driver for the NEMC on JZ4780 SoCs

2015-03-26T22:51:36Z

Add a driver for the NAND/External Memory Controller (NEMC) on JZ4780 and later SoCs. The primary function of this driver is to configure parameters, such as timings, for external memory devices using data supplied in the device tree. Devices connected to the NEMC are represented in the DT as children of the NEMC node, the driver uses optional properties specified in these child nodes to configure the parameters of each bank. Signed-off-by: Alex Smith Signed-off-by: Zubair Lutfullah Kakakhel Signed-off-by: Greg Kroah-Hartman

Merge tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2014-12-10T00:57:56Z

Pull ARM SoC/OMAP GPMC driver cleanup and move from Arnd Bergmann: "The GPMC driver has traditionally been considered a part of the OMAP platform code and tightly interweaved with some of the boards. With this cleanup, it has finally come to the point where it makes sense to move it out of arch/arm into drivers/memory, where we already have other drivers for similar hardware. The cleanups are still ongoing, with the goal of eventually having a standalone driver that does not require an interface to architecture code. This is a separate branch because of dependencies on multiple other branches, and to keep the drivers changes separate from the normal cleanups" * tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: memory: gpmc: Move omap gpmc code to live under drivers ARM: OMAP2+: Move GPMC initcall to devices.c ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header ARM: OMAP2+: Remove unnecesary include in GPMC driver ARM: OMAP2+: Drop board file for 3430sdp ARM: OMAP2+: Drop board file for ti8168evm ARM: OMAP2+: Drop legacy code for gpmc-smc91x.c ARM: OMAP2+: Require proper GPMC timings for devices ARM: OMAP2+: Show bootloader GPMC timings to allow configuring the .dts file ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select ARM: OMAP2+: gpmc: Sanity check GPMC fck on probe ARM: OMAP2+: gpmc: Keep Chip Select disabled while configuring it ARM: OMAP2+: gpmc: Always enable A26-A11 for non NAND devices ARM: OMAP2+: gpmc: Error out if timings fail in gpmc_probe_generic_child() ARM: OMAP2+: gpmc: Print error message in set_gpmc_timing_reg()

memory: Add NVIDIA Tegra memory controller support

2014-12-04T15:11:47Z

The memory controller on NVIDIA Tegra exposes various knobs that can be used to tune the behaviour of the clients attached to it. Currently this driver sets up the latency allowance registers to the HW defaults. Eventually an API should be exported by this driver (via a custom API or a generic subsystem) to allow clients to register latency requirements. This driver also registers an IOMMU (SMMU) that's implemented by the memory controller. It is supported on Tegra30, Tegra114 and Tegra124 currently. Tegra20 has a GART instead. The Tegra SMMU operates on memory clients and SWGROUPs. A memory client is a unidirectional, special-purpose DMA master. A SWGROUP represents a set of memory clients that form a logical functional unit corresponding to a single device. Typically a device has two clients: one client for read transactions and one client for write transactions, but there are also devices that have only read clients, but many of them (such as the display controllers). Because there is no 1:1 relationship between memory clients and devices the driver keeps a table of memory clients and the SWGROUPs that they belong to per SoC. Note that this is an exception and due to the fact that the SMMU is tightly integrated with the rest of the Tegra SoC. The use of these tables is discouraged in drivers for generic IOMMU devices such as the ARM SMMU because the same IOMMU could be used in any number of SoCs and keeping such tables for each SoC would not scale. Acked-by: Joerg Roedel Signed-off-by: Thierry Reding

memory: gpmc: Move omap gpmc code to live under drivers

2014-11-28T20:54:39Z

Just move to drivers as further clean-up can now happen there finally. Let's also add Roger and me to the MAINTAINERS so we get notified for any patches related to GPMC. Cc: Arnd Bergmann Acked-by: Roger Quadros Signed-off-by: Tony Lindgren