user/sven/linux.git/drivers/mfd, branch v4.19.54

mfd: twl6040: Fix device init errors for ACCCTL register

2019-06-15T09:54:03Z

[ Upstream commit 48171d0ea7caccf21c9ee3ae75eb370f2a756062 ] I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero: twl6040 0-004b: Failed to write 2d = 19: -121 And then any following register access will produce errors. There 2d offset above is register ACCCTL that gets written on twl6040 powerup. With error checking added to the related regcache_sync() call, the -EREMOTEIO error is reproducable on twl6040 powerup at least duovero. To fix the error, we need to wait until twl6040 is accessible after the powerup. Based on tests on omap4 duovero, we need to wait over 8ms after powerup before register write will complete without failures. Let's also make sure we warn about possible errors too. Note that we have twl6040_patch[] reg_sequence with the ACCCTL register configuration and regcache_sync() will write the new value to ACCCTL. Signed-off-by: Tony Lindgren Acked-by: Peter Ujfalusi Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: intel-lpss: Set the device in reset state when init

2019-06-15T09:54:02Z

[ Upstream commit dad06532292d77f37fbe831a02948a593500f682 ] In virtualized setup, when system reboots due to warm reset interrupt storm is seen. Call Trace: dump_stack+0x70/0xa5 __report_bad_irq+0x2e/0xc0 note_interrupt+0x248/0x290 ? add_interrupt_randomness+0x30/0x220 handle_irq_event_percpu+0x54/0x80 handle_irq_event+0x39/0x60 handle_fasteoi_irq+0x91/0x150 handle_irq+0x108/0x180 do_IRQ+0x52/0xf0 common_interrupt+0xf/0xf RIP: 0033:0x76fc2cfabc1d Code: 24 28 bf 03 00 00 00 31 c0 48 8d 35 63 77 0e 00 48 8d 15 2e 94 0e 00 4c 89 f9 49 89 d9 4c 89 d3 e8 b8 e2 01 00 48 8b 54 24 18 <48> 89 ef 48 89 de 4c 89 e1 e8 d5 97 01 00 84 c0 74 2d 48 8b 04 24 RSP: 002b:00007ffd247c1fc0 EFLAGS: 00000293 ORIG_RAX: ffffffffffffffda RAX: 0000000000000000 RBX: 00007ffd247c1ff0 RCX: 000000000003d3ce RDX: 0000000000000000 RSI: 00007ffd247c1ff0 RDI: 000076fc2cbb6010 RBP: 000076fc2cded010 R08: 00007ffd247c2210 R09: 00007ffd247c22a0 R10: 000076fc29465470 R11: 0000000000000000 R12: 00007ffd247c1fc0 R13: 000076fc2ce8e470 R14: 000076fc27ec9960 R15: 0000000000000414 handlers: [<000000000d3fa913>] idma64_irq Disabling IRQ #27 To avoid interrupt storm, set the device in reset state before bringing out the device from reset state. Changelog v2: - correct the subject line by adding "mfd: " Signed-off-by: Binbin Wu Acked-by: Mika Westerberg Reviewed-by: Andy Shevchenko Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: tps65912-spi: Add missing of table registration

2019-06-15T09:54:02Z

[ Upstream commit 9e364e87ad7f2c636276c773d718cda29d62b741 ] MODULE_DEVICE_TABLE(of, should be called to complete DT OF mathing mechanism and register it. Before this patch: modinfo drivers/mfd/tps65912-spi.ko | grep alias alias: spi:tps65912 After this patch: modinfo drivers/mfd/tps65912-spi.ko | grep alias alias: of:N*T*Cti,tps65912C* alias: of:N*T*Cti,tps65912 alias: spi:tps65912 Reported-by: Javier Martinez Canillas Signed-off-by: Daniel Gomez Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: twl-core: Disable IRQ while suspended

2019-05-08T05:21:48Z

[ Upstream commit 20bb907f7dc82ecc9e135ad7067ac7eb69c81222 ] Since commit 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend") on gta04 we have handle_twl4030_pih() called in situations where pm_runtime_get() in i2c-omap.c returns -EACCES. [ 86.474365] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done. [ 86.485473] printk: Suspending console(s) (use no_console_suspend to debug) [ 86.555572] Disabling non-boot CPUs ... [ 86.555664] Successfully put all powerdomains to target state [ 86.563720] twl: Read failed (mod 1, reg 0x01 count 1) [ 86.563751] twl4030: I2C error -13 reading PIH ISR [ 86.563812] twl: Read failed (mod 1, reg 0x01 count 1) [ 86.563812] twl4030: I2C error -13 reading PIH ISR [ 86.563873] twl: Read failed (mod 1, reg 0x01 count 1) [ 86.563903] twl4030: I2C error -13 reading PIH ISR This happens when we wakeup via something behing twl4030 (powerbutton or rtc alarm). This goes on for minutes until the system is finally resumed. Disable the irq on suspend and enable it on resume to avoid having i2c access problems when the irq registers are checked. Fixes: 6e2bd956936 ("i2c: omap: Use noirq system sleep pm ops to idle device for suspend") Signed-off-by: Andreas Kemnade Tested-by: Tony Lindgren Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: sm501: Fix potential NULL pointer dereference

2019-03-23T19:10:09Z

commit ae7b8eda27b33b1f688dfdebe4d46f690a8f9162 upstream. There is a potential NULL pointer dereference in case devm_kzalloc() fails and returns NULL. Fix this by adding a NULL check on *lookup* This bug was detected with the help of Coccinelle. Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva Signed-off-by: Lee Jones Signed-off-by: Greg Kroah-Hartman

mfd: mc13xxx: Fix a missing check of a register-read failure

2019-02-27T09:08:52Z

[ Upstream commit 9e28989d41c0eab57ec0bb156617a8757406ff8a ] When mc13xxx_reg_read() fails, "old_adc0" is uninitialized and will contain random value. Further execution uses "old_adc0" even when mc13xxx_reg_read() fails. The fix checks the return value of mc13xxx_reg_read(), and exits the execution when it fails. Signed-off-by: Kangjie Lu Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()

2019-02-27T09:08:52Z

[ Upstream commit 75d4c5e03c2ae9902ab521024b10291f6fc9515b ] Use devm_regmap_add_irq_chip and clean up error path in probe and also the remove function. Reported-by: Christian Hohnstaedt Signed-off-by: Keerthy Reviewed-by: Sebastian Reichel Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove

2019-02-27T09:08:52Z

[ Upstream commit 18e294ddafaeb80a1e2e10c9bd750a6cb8388d5b ] The driver adds different MFD child devices via mfd_add_devices() and hence it is required to call mfd_remove_devices() to remove MFD child devices. Fixes: 5e0115581bbc ("cros_ec: Move cros_ec_dev module to drivers/mfd") Signed-off-by: Enric Balletbo i Serra Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: axp20x: Add supported cells for AXP803

2019-02-27T09:08:52Z

[ Upstream commit ea90e7b47f0a8bd2fe14e9a88f523de7c67db90a ] Parts of the AXP803 are compatible with their counterparts on the AXP813. These include the GPIO, ADC, AC and battery power supplies. Signed-off-by: Oskari Lemmela Reviewed-by: Chen-Yu Tsai Tested-by: Vasily Khoruzhick Signed-off-by: Chen-Yu Tsai Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

mfd: axp20x: Re-align MFD cell entries

2019-02-27T09:08:51Z

[ Upstream commit 753a8d083e085c6f552c7982749de4cc7c40e2ac ] In the axp20x driver, the various mfd_cell lists had varying amounts of indentation, sometimes even within the same list. For the axp288, there's no alignment at all. Re-align the right hand side of the assignments with the least amount of tabs possible. Also collapse the closing bracket and the opening bracket of the next entry onto the same line for the axp288, to be consistent with all the other mfd_cell lists. This patch is whitespace change only. No functionality is modified. Signed-off-by: Chen-Yu Tsai Signed-off-by: Oskari Lemmela Signed-off-by: Lee Jones Signed-off-by: Sasha Levin