user/sven/linux.git/drivers/net/ipvlan, branch v5.1.17

net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set

2019-06-25T03:34:51Z

[ Upstream commit ceae266bf0ae6564ac16d086bf749a096fa90ded ] There's some NICs, such as hinic, with NETIF_F_IP_CSUM and NETIF_F_TSO on but NETIF_F_HW_CSUM off. And ipvlan device features will be NETIF_F_TSO on with NETIF_F_IP_CSUM and NETIF_F_IP_CSUM both off as IPVLAN_FEATURES only care about NETIF_F_HW_CSUM. So TSO will be disabled in netdev_fix_features. For example: Features for enp129s0f0: rx-checksumming: on tx-checksumming: on tx-checksum-ipv4: on tx-checksum-ip-generic: off [fixed] tx-checksum-ipv6: on Fixes: a188222b6ed2 ("net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK") Signed-off-by: Miaohe Lin Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2019-02-24T20:06:19Z

Three conflicts, one of which, for marvell10g.c is non-trivial and requires some follow-up from Heiner or someone else. The issue is that Heiner converted the marvell10g driver over to use the generic c45 code as much as possible. However, in 'net' a bug fix appeared which makes sure that a new local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0 is cleared. Signed-off-by: David S. Miller

ipvlan: disallow userns cap_net_admin to change global mode/flags

2019-02-22T19:27:19Z

When running Docker with userns isolation e.g. --userns-remap="default" and spawning up some containers with CAP_NET_ADMIN under this realm, I noticed that link changes on ipvlan slave device inside that container can affect all devices from this ipvlan group which are in other net namespaces where the container should have no permission to make changes to, such as the init netns, for example. This effectively allows to undo ipvlan private mode and switch globally to bridge mode where slaves can communicate directly without going through hostns, or it allows to switch between global operation mode (l2/l3/l3s) for everyone bound to the given ipvlan master device. libnetwork plugin here is creating an ipvlan master and ipvlan slave in hostns and a slave each that is moved into the container's netns upon creation event. * In hostns: # ip -d a [...] 8: cilium_host@bond0: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.0.1/32 scope link cilium_host valid_lft forever preferred_lft forever [...] * Spawn container & change ipvlan mode setting inside of it: # docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf 9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c # docker exec -ti client ip -d a [...] 10: cilium0@if4: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0 valid_lft forever preferred_lft forever # docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2 # docker exec -ti client ip -d a [...] 10: cilium0@if4: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0 valid_lft forever preferred_lft forever * In hostns (mode switched to l2): # ip -d a [...] 8: cilium_host@bond0: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.0.1/32 scope link cilium_host valid_lft forever preferred_lft forever [...] Same l3 -> l2 switch would also happen by creating another slave inside the container's network namespace when specifying the existing cilium0 link to derive the actual (bond0) master: # docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2 # docker exec -ti client ip -d a [...] 2: cilium1@if4: mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 10: cilium0@if4: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0 valid_lft forever preferred_lft forever * In hostns: # ip -d a [...] 8: cilium_host@bond0: mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000 link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535 ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 inet 10.41.0.1/32 scope link cilium_host valid_lft forever preferred_lft forever [...] One way to mitigate it is to check CAP_NET_ADMIN permissions of the ipvlan master device's ns, and only then allow to change mode or flags for all devices bound to it. Above two cases are then disallowed after the patch. Signed-off-by: Daniel Borkmann Acked-by: Mahesh Bandewar Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2019-02-08T23:00:17Z

An ipvlan bug fix in 'net' conflicted with the abstraction away of the IPV6 specific support in 'net-next'. Similarly, a bug fix for mlx5 in 'net' conflicted with the flow action conversion in 'net-next'. Signed-off-by: David S. Miller

ipvlan: decouple l3s mode dependencies from other modes

2019-02-08T19:16:48Z

Right now ipvlan has a hard dependency on CONFIG_NETFILTER and otherwise it cannot be built. However, the only ipvlan operation mode that actually depends on netfilter is l3s, everything else is independent of it. Break this hard dependency such that users are able to use ipvlan l3 mode on systems where netfilter is not compiled in. Therefore, this adds a hidden CONFIG_IPVLAN_L3S bool which is defaulting to y when CONFIG_NETFILTER is set in order to retain existing behavior for l3s. All l3s related code is refactored into ipvlan_l3s.c that is compiled in when enabled. Signed-off-by: Daniel Borkmann Cc: Mahesh Bandewar Cc: Florian Westphal Cc: Martynas Pumputis Acked-by: Florian Westphal Signed-off-by: David S. Miller

ipvlan, l3mdev: fix broken l3s mode wrt local routes

2019-01-31T06:13:34Z

While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin, I ran into the issue that while l3 mode is working fine, l3s mode does not have any connectivity to kube-apiserver and hence all pods end up in Error state as well. The ipvlan master device sits on top of a bond device and hostns traffic to kube-apiserver (also running in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573 where the latter is the address of the bond0. While in l3 mode, a curl to https://10.152.183.1:443 or to https://139.178.29.207:37573 works fine from hostns, neither of them do in case of l3s. In the latter only a curl to https://127.0.0.1:37573 appeared to work where for local addresses of bond0 I saw kernel suddenly starting to emit ARP requests to query HW address of bond0 which remained unanswered and neighbor entries in INCOMPLETE state. These ARP requests only happen while in l3s. Debugging this further, I found the issue is that l3s mode is piggy- backing on l3 master device, and in this case local routes are using l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant") and 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback"). I found that reverting them back into using the net->loopback_dev fixed ipvlan l3s connectivity and got everything working for the CNI. Now judging from 4fbae7d83c98 ("ipvlan: Introduce l3s mode") and the l3mdev paper in [0] the only sole reason why ipvlan l3s is relying on l3 master device is to get the l3mdev_ip_rcv() receive hook for setting the dst entry of the input route without adding its own ipvlan specific hacks into the receive path, however, any l3 domain semantics beyond just that are breaking l3s operation. Note that ipvlan also has the ability to dynamically switch its internal operation from l3 to l3s for all ports via ipvlan_set_port_mode() at runtime. In any case, l3 vs l3s soley distinguishes itself by 'de-confusing' netfilter through switching skb->dev to ipvlan slave device late in NF_INET_LOCAL_IN before handing the skb to L4. Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which, if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook without any additional l3mdev semantics on top. This should also have minimal impact since dev->priv_flags is already hot in cache. With this set, l3s mode is working fine and I also get things like masquerading pod traffic on the ipvlan master properly working. [0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant") Fixes: 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback") Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode") Signed-off-by: Daniel Borkmann Cc: Mahesh Bandewar Cc: David Ahern Cc: Florian Westphal Cc: Martynas Pumputis Acked-by: David Ahern Signed-off-by: David S. Miller

net: ipvlan: Issue NETDEV_PRE_CHANGEADDR

2018-12-14T02:41:38Z

A NETDEV_CHANGEADDR event implies a change of address of each of the IPVLANs of this IPVLAN device. Therefore propagate NETDEV_PRE_CHANGEADDR to all the IPVLANs. Signed-off-by: Petr Machata Acked-by: Jiri Pirko Reviewed-by: Ido Schimmel Signed-off-by: David S. Miller

ipvlan: Remove a useless comparison

2018-12-10T19:55:05Z

Fix following gcc warning: drivers/net/ipvlan/ipvlan_main.c:543:12: warning: comparison is always false due to limited range of data type [-Wtype-limits] 'mode' is a u16 variable, IPVLAN_MODE_L2 is zero, the comparison is always false Signed-off-by: YueHaibing Signed-off-by: David S. Miller

net: core: dev: Add extack argument to dev_change_flags()

2018-12-06T21:26:07Z

In order to pass extack together with NETDEV_PRE_UP notifications, it's necessary to route the extack to __dev_open() from diverse (possibly indirect) callers. One prominent API through which the notification is invoked is dev_change_flags(). Therefore extend dev_change_flags() with and extra extack argument and update all users. Most of the calls end up just encoding NULL, but several sites (VLAN, ipvlan, VRF, rtnetlink) do have extack available. Since the function declaration line is changed anyway, name the other function arguments to placate checkpatch. Signed-off-by: Petr Machata Acked-by: Jiri Pirko Reviewed-by: Ido Schimmel Reviewed-by: David Ahern Signed-off-by: David S. Miller

net: ipvlan: ipvlan_set_port_mode(): Add an extack argument

2018-12-06T21:26:06Z

A follow-up patch will extend dev_change_flags() with an extack argument. Extend ipvlan_set_port_mode() to have that argument available for the conversion. Signed-off-by: Petr Machata Acked-by: Jiri Pirko Reviewed-by: Ido Schimmel Signed-off-by: David S. Miller