user/sven/linux.git/drivers/net/usb, branch v5.4.3

r8152: avoid to call napi_disable twice

2019-11-22T18:07:44Z

Call napi_disable() twice would cause dead lock. There are three situations may result in the issue. 1. rtl8152_pre_reset() and set_carrier() are run at the same time. 2. Call rtl8152_set_tunable() after rtl8152_close(). 3. Call rtl8152_set_ringparam() after rtl8152_close(). For #1, use the same solution as commit 84811412464d ("r8152: Re-order napi_disable in rtl8152_close"). For #2 and #3, add checking the flag of IFF_UP and using napi_disable/napi_enable during mutex. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller

r8152: Re-order napi_disable in rtl8152_close

2019-11-20T20:48:13Z

Both rtl_work_func_t() and rtl8152_close() call napi_disable(). Since the two calls aren't protected by a lock, if the close function starts executing before the work function, we can get into a situation where the napi_disable() function is called twice in succession (first by rtl8152_close(), then by set_carrier()). In such a situation, the second call would loop indefinitely, since rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED bit. The rtl8152_close() function in turn issues a cancel_delayed_work_sync(), and so it would wait indefinitely for the rtl_work_func_t() to complete. Since rtl8152_close() is called by a process holding rtnl_lock() which is requested by other processes, this eventually leads to a system deadlock and crash. Re-order the napi_disable() call to occur after the work function disabling and urb cancellation calls are issued. Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e Reported-by: http://crbug.com/1017928 Signed-off-by: Prashant Malani Signed-off-by: David S. Miller

ax88172a: fix information leak on short answers

2019-11-15T20:18:45Z

If a malicious device gives a short MAC it can elicit up to 5 bytes of leaked memory out of the driver. We need to check for ETH_ALEN instead. Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum Signed-off-by: David S. Miller

net: cdc_ncm: Signedness bug in cdc_ncm_set_dgram_size()

2019-11-13T22:30:16Z

This code is supposed to test for negative error codes and partial reads, but because sizeof() is size_t (unsigned) type then negative error codes are type promoted to high positive values and the condition doesn't work as expected. Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU") Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller

net: usb: qmi_wwan: add support for Foxconn T77W968 LTE modules

2019-11-13T19:58:20Z

These are the Foxconn-branded variants of the Dell DW5821e modules, same USB layout as those. The QMI interface is exposed in USB configuration #1: P: Vendor=0489 ProdID=e0b4 Rev=03.18 S: Manufacturer=FII S: Product=T77W968 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option Signed-off-by: Aleksander Morgado Acked-by: Bjørn Mork Signed-off-by: David S. Miller

net: usb: qmi_wwan: add support for DW5821e with eSIM support

2019-11-07T23:49:49Z

Exactly same layout as the default DW5821e module, just a different vid/pid. The QMI interface is exposed in USB configuration #1: P: Vendor=413c ProdID=81e0 Rev=03.18 S: Manufacturer=Dell Inc. S: Product=DW5821e-eSIM Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option Signed-off-by: Aleksander Morgado Signed-off-by: David S. Miller

CDC-NCM: handle incomplete transfer of MTU

2019-11-07T23:27:06Z

A malicious device may give half an answer when asked for its MTU. The driver will proceed after this with a garbage MTU. Anything but a complete answer must be treated as an error. V2: used sizeof as request by Alexander Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum Signed-off-by: David S. Miller

net: usb: lan78xx: Disable interrupts before calling generic_handle_irq()

2019-10-28T23:35:04Z

lan78xx_status() will run with interrupts enabled due to the change in ed194d136769 ("usb: core: remove local_irq_save() around ->complete() handler"). generic_handle_irq() expects to be run with IRQs disabled. [ 4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts [ 4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168 [ 4.896294] 000: Modules linked in: [ 4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39 [ 4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT) [ 4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO) [ 4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168 [ 4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168 [ 4.896339] 000: sp : ffff000010003cc0 [ 4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060 [ 4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b [ 4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400 [ 4.896373] 000: x23: 000000000000004f x22: ffff000010003d64 [ 4.896381] 000: x21: 0000000000000000 x20: 0000000000000002 [ 4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060 [ 4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb [ 4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465 [ 4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0 [ 4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08 [ 4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920 [ 4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00 [ 4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510 [ 4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000 [ 4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000 [ 4.896466] 000: Call trace: [ 4.896471] 000: __handle_irq_event_percpu+0x154/0x168 [ 4.896481] 000: handle_irq_event_percpu+0x50/0xb0 [ 4.896489] 000: handle_irq_event+0x40/0x98 [ 4.896497] 000: handle_simple_irq+0xa4/0xf0 [ 4.896505] 000: generic_handle_irq+0x24/0x38 [ 4.896513] 000: intr_complete+0xb0/0xe0 [ 4.896525] 000: __usb_hcd_giveback_urb+0x58/0xd8 [ 4.896533] 000: usb_giveback_urb_bh+0xd0/0x170 [ 4.896539] 000: tasklet_action_common.isra.0+0x9c/0x128 [ 4.896549] 000: tasklet_hi_action+0x24/0x30 [ 4.896556] 000: __do_softirq+0x120/0x23c [ 4.896564] 000: irq_exit+0xb8/0xd8 [ 4.896571] 000: __handle_domain_irq+0x64/0xb8 [ 4.896579] 000: bcm2836_arm_irqchip_handle_irq+0x60/0xc0 [ 4.896586] 000: el1_irq+0xb8/0x140 [ 4.896592] 000: arch_cpu_idle+0x10/0x18 [ 4.896601] 000: do_idle+0x200/0x280 [ 4.896608] 000: cpu_startup_entry+0x20/0x28 [ 4.896615] 000: rest_init+0xb4/0xc0 [ 4.896623] 000: arch_call_rest_init+0xc/0x14 [ 4.896632] 000: start_kernel+0x454/0x480 Fixes: ed194d136769 ("usb: core: remove local_irq_save() around ->complete() handler") Cc: Woojung Huh Cc: Marc Zyngier Cc: Andrew Lunn Cc: Stefan Wahren Cc: Jisheng Zhang Cc: Sebastian Andrzej Siewior Cc: Thomas Gleixner Cc: David Miller Signed-off-by: Daniel Wagner Tested-by: Stefan Wahren Signed-off-by: David S. Miller

r8152: add device id for Lenovo ThinkPad USB-C Dock Gen 2

2019-10-21T19:06:41Z

This device is sold as 'ThinkPad USB-C Dock Gen 2 (40AS)'. Chipset is RTL8153 and works with r8152. Without this, the generic cdc_ether grabs the device, and the device jam connected networks up when the machine suspends. Signed-off-by: Kazutoshi Noguchi Signed-off-by: David S. Miller

net: usb: lan78xx: Connect PHY before registering MAC

2019-10-18T17:22:04Z

As soon as the netdev is registers, the kernel can start using the interface. If the driver connects the MAC to the PHY after the netdev is registered, there is a race condition where the interface can be opened without having the PHY connected. Change the order to close this race condition. Fixes: 92571a1aae40 ("lan78xx: Connect phy early") Reported-by: Daniel Wagner Signed-off-by: Andrew Lunn Tested-by: Daniel Wagner Signed-off-by: David S. Miller