user/sven/linux.git/drivers/net/wireless, branch v3.2.64

Revert "iwlwifi: dvm: don't enable CTS to self"

2014-11-05T20:27:39Z

commit f47f46d7b09cf1d09e4b44b6cc4dd7d68a08028c upstream. This reverts commit 43d826ca5979927131685cc2092c7ce862cb91cd. This commit caused packet loss. Signed-off-by: Emmanuel Grumbach [bwh: Backported to 3.2: - Adjust filename - Condition for RXON_FLG_SELF_CTS_EN in iwlagn_commit_rxon() was different] Signed-off-by: Ben Hutchings

rtlwifi: rtl8192cu: Add new ID

2014-11-05T20:27:39Z

commit c66517165610b911e4c6d268f28d8c640832dbd1 upstream. The Sitecom WLA-2102 adapter uses this driver. Reported-by: Nico Baggus Signed-off-by: Larry Finger Cc: Nico Baggus Signed-off-by: John W. Linville Signed-off-by: Ben Hutchings

carl9170: fix sending URBs with wrong type when using full-speed

2014-09-13T22:41:44Z

commit 671796dd96b6cd85b75fba9d3007bcf7e5f7c309 upstream. The driver assumes that endpoint 4 is always an interrupt endpoint. Unfortunately the type differs between high-speed and full-speed configurations while in the former case it is indeed an interrupt endpoint this is not true for the latter case - here it is a bulk endpoint. When sending URBs with the wrong type the kernel will generate a warning message including backtrace. In this specific case there will be a huge amount of warnings which can bring the system to freeze. To fix this we are now sending URBs to endpoint 4 using the type found in the endpoint descriptor. A side note: The carl9170 firmware currently specifies endpoint 4 as interrupt endpoint even in the full-speed configuration but this has no relevance because before this firmware is loaded the endpoint type is as described above and after the firmware is running the stick is not reenumerated and so the old descriptor is used. Signed-off-by: Ronald Wahl Signed-off-by: John W. Linville Signed-off-by: Ben Hutchings

iwlwifi: dvm: don't enable CTS to self

2014-08-06T17:07:34Z

commit 43d826ca5979927131685cc2092c7ce862cb91cd upstream. We should always prefer to use full RTS protection. Using CTS to self gives a meaningless improvement, but this flow is much harder for the firmware which is likely to have issues with it. Signed-off-by: Emmanuel Grumbach [bwh: Backported to 3.2: - Adjust filename - Condition for RXON_FLG_SELF_CTS_EN in iwlagn_commit_rxon() was different] Signed-off-by: Ben Hutchings

mwifiex: fix Tx timeout issue

2014-08-06T17:07:33Z

commit d76744a93246eccdca1106037e8ee29debf48277 upstream. https://bugzilla.kernel.org/show_bug.cgi?id=70191 https://bugzilla.kernel.org/show_bug.cgi?id=77581 It is observed that sometimes Tx packet is downloaded without adding driver's txpd header. This results in firmware parsing garbage data as packet length. Sometimes firmware is unable to read the packet if length comes out as invalid. This stops further traffic and timeout occurs. The root cause is uninitialized fields in tx_info(skb->cb) of packet used to get garbage values. In this case if MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd header was skipped. This patch makes sure that tx_info is correctly initialized to fix the problem. Reported-by: Andrew Wiley Reported-by: Linus Gasser Reported-by: Michael Hirsch Tested-by: Xinming Hu Signed-off-by: Amitkumar Karwar Signed-off-by: Maithili Hinge Signed-off-by: Avinash Patil Signed-off-by: Bing Zhao Signed-off-by: John W. Linville [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

b43: fix frequency reported on G-PHY with /new/ firmware

2014-07-11T12:33:53Z

commit 2fc68eb122c7ea6cd5be1fe7d6650c0beb2f4f40 upstream. Support for firmware rev 508+ was added years ago, but we never noticed it reports channel in a different way for G-PHY devices. Instead of offset from 2400 MHz it simply passes channel id (AKA hw_value). So far it was (most probably) affecting monitor mode users only, but the following recent commit made it noticeable for quite everybody: commit 3afc2167f60a327a2c1e1e2600ef209a3c2b75b7 Author: Emmanuel Grumbach Date: Tue Mar 4 16:50:13 2014 +0200 cfg80211/mac80211: ignore signal if the frame was heard on wrong channel Reported-by: Aaro Koskinen Signed-off-by: Rafał Miłecki Tested-by: Aaro Koskinen Signed-off-by: John W. Linville Signed-off-by: Ben Hutchings

rt2x00: disable TKIP on USB

2014-07-11T12:33:52Z

commit 8edcb0ba0d56f5914eef11eda6db8bfe74eb9ca8 upstream. On USB we can not get atomically TKIP key. We have to disable support for TKIP acceleration on USB hardware to avoid bug as showed bellow. [ 860.827243] BUG: scheduling while atomic: hostapd/3397/0x00000002 [ 860.827280] Call Trace: [ 860.827282] [] dump_stack+0x4d/0x66 [ 860.827284] [] __schedule_bug+0x47/0x55 [ 860.827285] [] __schedule+0x733/0x7b0 [ 860.827287] [] schedule+0x29/0x70 [ 860.827289] [] schedule_timeout+0x15a/0x2b0 [ 860.827291] [] ? ftrace_raw_event_tick_stop+0xc0/0xc0 [ 860.827294] [] ? __module_text_address+0x12/0x70 [ 860.827296] [] wait_for_completion_timeout+0xb3/0x140 [ 860.827298] [] ? wake_up_state+0x20/0x20 [ 860.827301] [] usb_start_wait_urb+0x7d/0x150 [ 860.827303] [] usb_control_msg+0xc5/0x110 [ 860.827305] [] rt2x00usb_vendor_request+0xc6/0x160 [rt2x00usb] [ 860.827307] [] rt2x00usb_vendor_req_buff_lock+0x75/0x150 [rt2x00usb] [ 860.827309] [] rt2x00usb_vendor_request_buff+0xa3/0xe0 [rt2x00usb] [ 860.827311] [] rt2x00usb_register_multiread+0x33/0x40 [rt2800usb] [ 860.827314] [] rt2800_get_tkip_seq+0x39/0x50 [rt2800lib] [ 860.827321] [] ieee80211_get_key+0x218/0x2a0 [mac80211] [ 860.827322] [] ? __nlmsg_put+0x6c/0x80 [ 860.827329] [] nl80211_get_key+0x22e/0x360 [cfg80211] Reported-and-tested-by: Peter Wu Reported-and-tested-by: Pontus Fuchs Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville Signed-off-by: Ben Hutchings

rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()

2014-06-09T12:29:05Z

commit 3234f5b06fc3094176a86772cc64baf3decc98fc upstream. Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Signed-off-by: Ben Hutchings Signed-off-by: John W. Linville [bwh: Backported to 3.2: adjust context]

rtlwifi: rtl8192cu: Fix too long disable of IRQs

2014-06-09T12:29:05Z

commit a53268be0cb9763f11da4f6fe3fb924cbe3a7d4a upstream. In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8192cu. Signed-off-by: Larry Finger Signed-off-by: John W. Linville [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

rt2x00: fix beaconing on USB

2014-06-09T12:29:01Z

commit 8834d3608cc516f13e2e510f4057c263f3d2ce42 upstream. When disable beaconing we clear register with beacon and newer set it back, what make we stop send beacons infinitely. Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville Signed-off-by: Ben Hutchings