user/sven/linux.git/drivers/net, branch v3.4.28

igb: release already assigned MSI-X interrupts if setup fails

2013-01-21T19:45:25Z

commit 52285b762b3681669215bf1d17ca6143448ab7d3 upstream. During MSI-X setup the system might run out of vectors. If this happens the already assigned vectors for this NIC should be freed before trying the disable MSI-X. Failing to do so results in the following oops. kernel BUG at drivers/pci/msi.c:341! [...] Call Trace: [] pci_disable_msix+0x3d/0x60 [] igb_reset_interrupt_capability+0x27/0x5c [igb] [] igb_clear_interrupt_scheme+0x26/0x2d [igb] [] igb_request_irq+0x73/0x297 [igb] [] __igb_open+0xc8/0x223 [igb] [] igb_open+0x13/0x15 [igb] [] __dev_open+0xbf/0x120 [] __dev_change_flags+0xa1/0x180 [] dev_change_flags+0x28/0x70 [] devinet_ioctl+0x5b7/0x620 [] inet_ioctl+0x88/0xa0 [] sock_do_ioctl+0x30/0x70 [] sock_ioctl+0x72/0x270 [] do_vfs_ioctl+0x8c/0x340 [] sys_ioctl+0xa1/0xb0 [] system_call_fastpath+0x16/0x1b Code: 48 89 df e8 1f 40 ed ff 4d 39 e6 49 8b 45 10 75 b6 48 83 c4 18 5b 41 5c 41 5d 41 5e 41 5f c9 c3 48 8b 7b 20 e8 3e 91 db ff eb ae <0f> 0b eb fe 0f 1f 84 00 00 00 00 00 55 48 89 e5 0f 1f 44 00 00 RIP [] free_msi_irqs+0x124/0x130 RSP Signed-off-by: Stefan Assmann Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher Signed-off-by: Abdallah Chatila

r8169: avoid NAPI scheduling delay.

2013-01-21T19:45:24Z

commit 7dbb491878a2c51d372a8890fa45a8ff80358af1 upstream. While reworking the r8169 driver a few months ago to perform the smallest amount of work in the irq handler, I took care of avoiding any irq mask register operation in the slow work dedicated user context thread. The slow work thread scheduled an extra round of NAPI work which would ultimately set the irq mask register as required, thus keeping such irq mask operations in the NAPI handler. It would eventually race with the irq handler and delay NAPI execution for - assuming no further irq - a whole ksoftirqd period. Mildly a problem for rare link changes or corner case PCI events. The race was always lost after the last bh disabling lock had been removed from the work thread and people started wondering where those pesky "NOHZ: local_softirq_pending 08" messages came from. Actually the irq mask register _can_ be set up directly in the slow work thread. Signed-off-by: Francois Romieu Reported-by: Dave Jones Tested-by: Marc Dionne Cc: Thomas Gleixner Cc: Hayes Wang Signed-off-by: David S. Miller

b43: Fix firmware loading when driver is built into the kernel

2013-01-17T16:51:04Z

commit 5e20a4b53094651d80f856ff55a916b999dbb57a upstream. Recent versions of udev cause synchronous firmware loading from the probe routine to fail because the request to user space would time out. The original fix for b43 (commit 6b6fa58) moved the firmware load from the probe routine to a work queue, but it still used synchronous firmware loading. This method is OK when b43 is built as a module; however, it fails when the driver is compiled into the kernel. This version changes the code to load the initial firmware file using request_firmware_nowait(). A completion event is used to hold the work queue until that file is available. This driver reads several firmware files - the remainder can be read synchronously. On some test systems, the async read fails; however, a following synch read works, thus the async failure falls through to the sync try. Reported-and-Tested by: Felix Janda Signed-off-by: Larry Finger Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

mwifiex: check wait_event_interruptible return value

2013-01-17T16:51:04Z

commit 9c969d8ccb1e17bd20742f4ac9f00c1a64487234 upstream. wait_event_interruptible function returns -ERESTARTSYS if it's interrupted by a signal. Driver should check the return value and handle this case properly. In mwifiex_wait_queue_complete() routine, as we are now checking wait_event_interruptible return value, the condition check is not required. Also, we have removed mwifiex_cancel_pending_ioctl() call to avoid a chance of sending second command to FW by other path as soon as we clear current command node. FW can not handle two commands simultaneously. Signed-off-by: Bing Zhao Signed-off-by: Amitkumar Karwar Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

i2400m: add Intel 6150 device IDs

2013-01-17T16:50:46Z

commit 999a7c5776a0ed2133645fa7e008bec05bda9254 upstream. Add device IDs for WiMAX function of Intel 6150 cards. Signed-off-by: Dan Williams Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

ath9k_hw: Fix signal strength / channel noise reporting

2013-01-17T16:50:43Z

commit b7c0c238898d200e80487516e2b67aba2a522cc0 upstream. While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor for a chip measured in clean air, it refers to the lowest expected reading. Depending on the frequency, this measurement can vary by about 6db, thus causing a higher reported channel noise and signal strength. Factor in the 6db offset when converting internal noisefloor to channel noise. This patch makes the reported values more accurate for all chips without affecting NF calibration behavior. Signed-off-by: Felix Fietkau Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

ath9k: ar9003: fix OTP register offsets for AR9340

2013-01-17T16:50:43Z

commit b3cd8021379306c0be6932e4d3b4b01efc681769 upstream. Trying to access the OTP memory on the AR9340 causes a data bus error like this: Data bus error, epc == 86e84164, ra == 86e84164 Oops[#1]: Cpu 0 $ 0 : 00000000 00000061 deadc0de 00000000 $ 4 : b8115f18 00015f18 00000007 00000004 $ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c $12 : 7c7c3c7c 001f0041 00000000 7c7c7c3c $16 : 86ee0000 00015f18 00000000 00000007 $20 : 00000004 00000064 00000004 86d71c44 $24 : 00000000 86e6ca00 $28 : 86d70000 86d71b20 86ece0c0 86e84164 Hi : 00000000 Lo : 00000064 epc : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw] Tainted: G O ra : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw] Status: 1100d403 KERNEL EXL IE Cause : 4080801c PrId : 0001974c (MIPS 74Kc) Modules linked in: ath9k(O+) ath9k_common(O) ath9k_hw(O) ath(O) ar934x_nfc mac80211(O) usbcore usb_common scsi_mod nls_base nand nand_ecc nand_ids crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crypto_blkcipher cryptomgr aead crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio Process insmod (pid: 459, threadinfo=86d70000, task=87942140, tls=779ac440) Stack : 802fb500 000200da 804db150 804e0000 87816130 86ee0000 00010000 86d71b88 86d71bc0 00000004 00000003 86e9fcd0 80305300 0002c0d0 86e74c50 800b4c20 000003e8 00000001 00000000 86ee0000 000003ff 86e9fd64 80305300 80123938 fffffffc 00000004 000058bc 00000000 86ea0000 86ee0000 000001ff 878d6000 99999999 86e9fdc0 86ee0fcc 86e9e664 0000c0d0 86ee0000 0000700000007000 ... Call Trace: [<86e84164>] ath9k_hw_wait+0x58/0xb0 [ath9k_hw] [<86e9fcd0>] ath9k_hw_setup_statusring+0x16b8/0x1c7c [ath9k_hw] Code: 0000a812 0040f809 00000000 <00531024> 1054000b 24020001 0c05b5dc 2404000a 26520001 The cause of the error is that the OTP register offsets are different on the AR9340 than the actually used values. Signed-off-by: Gabor Juhos Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

Revert "ath9k_hw: Update AR9003 high_power tx gain table"

2013-01-17T16:50:43Z

commit 9c170e068636deb3e3f96114034bb711675f0faa upstream. This reverts commit f74b9d365ddd33a375802b064f96a5d0e99af7c0. Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd "ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to bring the tx power back to normal levels on devices like the Buffalo WZR-HP-G450H, this one needs to be reverted as well. This revert improves tx power by ~10 db on that device Signed-off-by: Felix Fietkau Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

ath5k: fix tx path skb leaks

2013-01-17T16:50:41Z

commit 596ab5ec3bf10a22be30d7cb1d903a4b83fd607c upstream. ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for tx packets passed to the driver from mac80211 Signed-off-by: Felix Fietkau Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

can: Do not call dev_put if restart timer is running upon close

2013-01-11T17:07:18Z

commit ab48b03ec9ae1840a1e427e2375bd0d9d554b4ed upstream. If the restart timer is running due to BUS-OFF and the device is disconnected an dev_put will decrease the usage counter to -1 thus blocking the interface removal, resulting in the following dmesg lines repeating every 10s: can: notifier: receive list not found for dev can0 can: notifier: receive list not found for dev can0 can: notifier: receive list not found for dev can0 unregister_netdevice: waiting for can0 to become free. Usage count = -1 Signed-off-by: Alexander Stein Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman