user/sven/linux.git/drivers/net, branch v4.9.53

mac80211_hwsim: Use proper TX power

2017-10-05T07:43:58Z

commit 9de981f507474f326e42117858dc9a9321331ae5 upstream. In struct ieee80211_tx_info, control.vif pointer and rate_driver_data[0] falls on the same place, depending on the union usage. During the whole TX process, the union is referred to as a control struct, which holds the vif that is later used in the tx flow, especially in order to derive the used tx power. Referring direcly to rate_driver_data[0] and assigning a value to it, overwrites the vif pointer, hence making all later references irrelevant. Moreover, rate_driver_data[0] isn't used later in the flow in order to retrieve the channel that it is pointing to. Signed-off-by: Beni Lev Signed-off-by: Luca Coelho Signed-off-by: Johannes Berg Signed-off-by: Greg Kroah-Hartman

gianfar: Fix Tx flow control deactivation

2017-09-20T06:19:56Z

[ Upstream commit 5d621672bc1a1e5090c1ac5432a18c79e0e13e03 ] The wrong register is checked for the Tx flow control bit, it should have been maccfg1 not maccfg2. This went unnoticed for so long probably because the impact is hardly visible, not to mention the tangled code from adjust_link(). First, link flow control (i.e. handling of Rx/Tx link level pause frames) is disabled by default (needs to be enabled via 'ethtool -A'). Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few old boards), which results in Tx flow control remaining always on once activated. Fixes: 45b679c9a3ccd9e34f28e6ec677b812a860eb8eb ("gianfar: Implement PAUSE frame generation support") Signed-off-by: Claudiu Manoil Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

mlxsw: spectrum: Forbid linking to devices that have uppers

2017-09-20T06:19:55Z

[ Upstream commit 25cc72a33835ed8a6f53180a822cadab855852ac ] The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the device in case a port is enslaved to a master netdev such as bridge or bond. Since the driver ignores events unrelated to its ports and their uppers, it's possible to engineer situations in which the device's data path differs from the kernel's. One example to such a situation is when a port is enslaved to a bond that is already enslaved to a bridge. When the bond was enslaved the driver ignored the event - as the bond wasn't one of its uppers - and therefore a bridge port instance isn't created in the device. Until such configurations are supported forbid them by checking that the upper device doesn't have uppers of its own. Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave") Signed-off-by: Ido Schimmel Reported-by: Nogah Frankel Tested-by: Nogah Frankel Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

Revert "net: phy: Correctly process PHY_HALTED in phy_stop_machine()"

2017-09-20T06:19:55Z

[ Upstream commit ebc8254aeae34226d0bc8fda309fd9790d4dccfe ] This reverts commit 7ad813f208533cebfcc32d3d7474dc1677d1b09a ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()") because it is creating the possibility for a NULL pointer dereference. David Daney provide the following call trace and diagram of events: When ndo_stop() is called we call: phy_disconnect() +---> phy_stop_interrupts() implies: phydev->irq = PHY_POLL; +---> phy_stop_machine() | +---> phy_state_machine() | +----> queue_delayed_work(): Work queued. +--->phy_detach() implies: phydev->attached_dev = NULL; Now at a later time the queued work does: phy_state_machine() +---->netif_carrier_off(phydev->attached_dev): Oh no! It is NULL: CPU 12 Unable to handle kernel paging request at virtual address 0000000000000048, epc == ffffffff80de37ec, ra == ffffffff80c7c Oops[#1]: CPU: 12 PID: 1502 Comm: kworker/12:1 Not tainted 4.9.43-Cavium-Octeon+ #1 Workqueue: events_power_efficient phy_state_machine task: 80000004021ed100 task.stack: 8000000409d70000 $ 0 : 0000000000000000 ffffffff84720060 0000000000000048 0000000000000004 $ 4 : 0000000000000000 0000000000000001 0000000000000004 0000000000000000 $ 8 : 0000000000000000 0000000000000000 00000000ffff98f3 0000000000000000 $12 : 8000000409d73fe0 0000000000009c00 ffffffff846547c8 000000000000af3b $16 : 80000004096bab68 80000004096babd0 0000000000000000 80000004096ba800 $20 : 0000000000000000 0000000000000000 ffffffff81090000 0000000000000008 $24 : 0000000000000061 ffffffff808637b0 $28 : 8000000409d70000 8000000409d73cf0 80000000271bd300 ffffffff80c7804c Hi : 000000000000002a Lo : 000000000000003f epc : ffffffff80de37ec netif_carrier_off+0xc/0x58 ra : ffffffff80c7804c phy_state_machine+0x48c/0x4f8 Status: 14009ce3 KX SX UX KERNEL EXL IE Cause : 00800008 (ExcCode 02) BadVA : 0000000000000048 PrId : 000d9501 (Cavium Octeon III) Modules linked in: Process kworker/12:1 (pid: 1502, threadinfo=8000000409d70000, task=80000004021ed100, tls=0000000000000000) Stack : 8000000409a54000 80000004096bab68 80000000271bd300 80000000271c1e00 0000000000000000 ffffffff808a1708 8000000409a54000 80000000271bd300 80000000271bd320 8000000409a54030 ffffffff80ff0f00 0000000000000001 ffffffff81090000 ffffffff808a1ac0 8000000402182080 ffffffff84650000 8000000402182080 ffffffff84650000 ffffffff80ff0000 8000000409a54000 ffffffff808a1970 0000000000000000 80000004099e8000 8000000402099240 0000000000000000 ffffffff808a8598 0000000000000000 8000000408eeeb00 8000000409a54000 00000000810a1d00 0000000000000000 8000000409d73de8 8000000409d73de8 0000000000000088 000000000c009c00 8000000409d73e08 8000000409d73e08 8000000402182080 ffffffff808a84d0 8000000402182080 ... Call Trace: [] netif_carrier_off+0xc/0x58 [] phy_state_machine+0x48c/0x4f8 [] process_one_work+0x158/0x368 [] worker_thread+0x150/0x4c0 [] kthread+0xc8/0xe0 [] ret_from_kernel_thread+0x14/0x1c The original motivation for this change originated from Marc Gonzales indicating that his network driver did not have its adjust_link callback executing with phydev->link = 0 while he was expecting it. PHYLIB has never made any such guarantees ever because phy_stop() merely just tells the workqueue to move into PHY_HALTED state which will happen asynchronously. Reported-by: Geert Uytterhoeven Reported-by: David Daney Fixes: 7ad813f20853 ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

cxgb4: Fix stack out-of-bounds read due to wrong size to t4_record_mbox()

2017-09-20T06:19:54Z

[ Upstream commit 0f3086868e8889a823a6e0f3d299102aa895d947 ] Passing commands for logging to t4_record_mbox() with size MBOX_LEN, when the actual command size is actually smaller, causes out-of-bounds stack accesses in t4_record_mbox() while copying command words here: for (i = 0; i < size / 8; i++) entry->cmd[i] = be64_to_cpu(cmd[i]); Up to 48 bytes from the stack are then leaked to debugfs. This happens whenever we send (and log) commands described by structs fw_sched_cmd (32 bytes leaked), fw_vi_rxmode_cmd (48), fw_hello_cmd (48), fw_bye_cmd (48), fw_initialize_cmd (48), fw_reset_cmd (48), fw_pfvf_cmd (32), fw_eq_eth_cmd (16), fw_eq_ctrl_cmd (32), fw_eq_ofld_cmd (32), fw_acl_mac_cmd(16), fw_rss_glb_config_cmd(32), fw_rss_vi_config_cmd(32), fw_devlog_cmd(32), fw_vi_enable_cmd(48), fw_port_cmd(32), fw_sched_cmd(32), fw_devlog_cmd(32). The cxgb4vf driver got this right instead. When we call t4_record_mbox() to log a command reply, a MBOX_LEN size can be used though, as get_mbox_rpl() will fill cmd_rpl up completely. Fixes: 7f080c3f2ff0 ("cxgb4: Add support to enable logging of firmware mailbox commands") Signed-off-by: Stefano Brivio Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

netvsc: fix deadlock betwen link status and removal

2017-09-20T06:19:54Z

[ Upstream commit 9b4e946ce14e20d7addbfb7d9139e604f9fda107 ] There is a deadlock possible when canceling the link status delayed work queue. The removal process is run with RTNL held, and the link status callback is acquring RTNL. Resolve the issue by using trylock and rescheduling. If cancel is in process, that block it from happening. Fixes: 122a5f6410f4 ("staging: hv: use delayed_work for netvsc_send_garp()") Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

qlge: avoid memcpy buffer overflow

2017-09-20T06:19:54Z

[ Upstream commit e58f95831e7468d25eb6e41f234842ecfe6f014f ] gcc-8.0.0 (snapshot) points out that we copy a variable-length string into a fixed length field using memcpy() with the destination length, and that ends up copying whatever follows the string: inlined from 'ql_core_dump' at drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:1106:2: drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:708:2: error: 'memcpy' reading 15 bytes from a region of size 14 [-Werror=stringop-overflow=] memcpy(seg_hdr->description, desc, (sizeof(seg_hdr->description)) - 1); Changing it to use strncpy() will instead zero-pad the destination, which seems to be the right thing to do here. The bug is probably harmless, but it seems like a good idea to address it in stable kernels as well, if only for the purpose of building with gcc-8 without warnings. Fixes: a61f80261306 ("qlge: Add ethtool register dump function.") Signed-off-by: Arnd Bergmann Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

fsl/man: Inherit parent device and of_node

2017-09-20T06:19:54Z

[ Upstream commit a1a50c8e4c241a505b7270e1a3c6e50d94e794b1 ] Junote Cai reported that he was not able to get a DSA setup involving the Freescale DPAA/FMAN driver to work and narrowed it down to of_find_net_device_by_node(). This function requires the network device's device reference to be correctly set which is the case here, though we have lost any device_node association there. The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent device and the of_node when dpaa_eth_add_device() creates the platform device. Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

macsec: add genl family module alias

2017-09-20T06:19:53Z

[ Upstream commit 78362998f58c7c271e2719dcd0aaced435c801f9 ] This helps tools such as wpa_supplicant can start even if the macsec module isn't loaded yet. Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Sabrina Dubroca Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

mwifiex: correct channel stat buffer overflows

2017-09-09T15:39:40Z

commit 4b5dde2d6234ff5bc68e97e6901d1f2a0a7f3749 upstream. mwifiex records information about various channels as it receives scan information. It does this by appending to a buffer that was sized to the max number of supported channels on any band, but there are numerous problems: (a) scans can return info from more than one band (e.g., both 2.4 and 5 GHz), so the determined "max" is not large enough (b) some firmware appears to return multiple results for a given channel, so the max *really* isn't large enough (c) there is no bounds checking when stashing these stats, so problems (a) and (b) can easily lead to buffer overflows Let's patch this by setting a slightly-more-correct max (that accounts for a combination of both 2.4G and 5G bands) and adding a bounds check when writing to our statistics buffer. Due to problem (b), we still might not properly report all known survey information (e.g., with "iw survey dump"), since duplicate results (or otherwise "larger than expected" results) will cause some truncation. But that's a problem for a future bugfix. (And because of this known deficiency, only log the excess at the WARN level, since that isn't visible by default in this driver and would otherwise be a bit too noisy.) Fixes: bf35443314ac ("mwifiex: channel statistics support for mwifiex") Cc: Avinash Patil Cc: Xinming Hu Signed-off-by: Brian Norris Reviewed-by: Dmitry Torokhov Reviewed-by: Ganapathi Bhat Signed-off-by: Kalle Valo Signed-off-by: Greg Kroah-Hartman