user/sven/linux.git/drivers/net, branch v5.1.17

net: aquantia: fix vlans not working over bridged network

2019-07-03T11:13:42Z

[ Upstream commit 48dd73d08d4dda47ee31cc8611fb16840fc16803 ] In configuration of vlan over bridge over aquantia device it was found that vlan tagged traffic is dropped on chip. The reason is that bridge device enables promisc mode, but in atlantic chip vlan filters will still apply. So we have to corellate promisc settings with vlan configuration. The solution is to track in a separate state variable the need of vlan forced promisc. And also consider generic promisc configuration when doing vlan filter config. Fixes: 7975d2aff5af ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov Signed-off-by: Igor Russkikh Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

tun: wake up waitqueues after IFF_UP is set

2019-07-03T11:13:42Z

[ Upstream commit 72b319dc08b4924a29f5e2560ef6d966fa54c429 ] Currently after setting tap0 link up, the tun code wakes tx/rx waited queues up in tun_net_open() when .ndo_open() is called, however the IFF_UP flag has not been set yet. If there's already a wait queue, it would fail to transmit when checking the IFF_UP flag in tun_sendmsg(). Then the saving vhost_poll_start() will add the wq into wqh until it is waken up again. Although this works when IFF_UP flag has been set when tun_chr_poll detects; this is not true if IFF_UP flag has not been set at that time. Sadly the latter case is a fatal error, as the wq will never be waken up in future unless later manually setting link up on purpose. Fix this by moving the wakeup process into the NETDEV_UP event notifying process, this makes sure IFF_UP has been set before all waited queues been waken up. Signed-off-by: Fei Li Acked-by: Jason Wang Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

team: Always enable vlan tx offload

2019-07-03T11:13:41Z

[ Upstream commit ee4297420d56a0033a8593e80b33fcc93fda8509 ] We should rather have vlan_tci filled all the way down to the transmitting netdevice and let it do the hw/sw vlan implementation. Suggested-by: Jiri Pirko Signed-off-by: YueHaibing Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: stmmac: set IC bit when transmitting frames with HW timestamp

2019-07-03T11:13:41Z

[ Upstream commit d0bb82fd60183868f46c8ccc595a3d61c3334a18 ] When transmitting certain PTP frames, e.g. SYNC and DELAY_REQ, the PTP daemon, e.g. ptp4l, is polling the driver for the frame transmit hardware timestamp. The polling will most likely timeout if the tx coalesce is enabled due to the Interrupt-on-Completion (IC) bit is not set in tx descriptor for those frames. This patch will ignore the tx coalesce parameter and set the IC bit when transmitting PTP frames which need to report out the frame transmit hardware timestamp to user space. Fixes: f748be531d70 ("net: stmmac: Rework coalesce timer and fix multi-queue races") Signed-off-by: Roland Hii Signed-off-by: Ong Boon Leong Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: stmmac: fixed new system time seconds value calculation

2019-07-03T11:13:41Z

[ Upstream commit a1e5388b4d5fc78688e5e9ee6641f779721d6291 ] When ADDSUB bit is set, the system time seconds field is calculated as the complement of the seconds part of the update value. For example, if 3.000000001 seconds need to be subtracted from the system time, this field is calculated as 2^32 - 3 = 4294967296 - 3 = 0x100000000 - 3 = 0xFFFFFFFD Previously, the 0x100000000 is mistakenly written as 100000000. This is further simplified from sec = (0x100000000ULL - sec); to sec = -sec; Fixes: ba1ffd74df74 ("stmmac: fix PTP support for GMAC4") Signed-off-by: Roland Hii Signed-off-by: Ong Boon Leong Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

bonding: Always enable vlan tx offload

2019-07-03T11:13:40Z

[ Upstream commit 30d8177e8ac776d89d387fad547af6a0f599210e ] We build vlan on top of bonding interface, which vlan offload is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is BOND_XMIT_POLICY_ENCAP34. Because vlan tx offload is off, vlan tci is cleared and skb push the vlan header in validate_xmit_vlan() while sending from vlan devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to get information from protocol headers encapsulated within vlan, because 'nhoff' is points to IP header, so bond hashing is based on layer 2 info, which fails to distribute packets across slaves. This patch always enable bonding's vlan tx offload, pass the vlan packets to the slave devices with vlan tci, let them to handle vlan implementation. Fixes: 278339a42a1b ("bonding: propogate vlan_features to bonding master") Suggested-by: Jiri Pirko Signed-off-by: YueHaibing Acked-by: Jiri Pirko Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

qmi_wwan: Fix out-of-bounds read

2019-07-03T11:13:35Z

[ Upstream commit 904d88d743b0c94092c5117955eab695df8109e8 ] The syzbot reported Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x67/0x231 mm/kasan/report.c:188 __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317 kasan_report+0xe/0x20 mm/kasan/common.c:614 qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417 usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361 really_probe+0x281/0x660 drivers/base/dd.c:509 driver_probe_device+0x104/0x210 drivers/base/dd.c:670 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 Caused by too many confusing indirections and casts. id->driver_info is a pointer stored in a long. We want the pointer here, not the address of it. Thanks-to: Hillf Danton Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com Cc: Kristian Evensen Fixes: e4bf63482c30 ("qmi_wwan: Add quirk for Quectel dynamic config") Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

can: flexcan: fix timeout when set small bitrate

2019-06-25T03:34:53Z

commit 247e5356a709eb49a0d95ff2a7f07dac05c8252c upstream. Current we can meet timeout issue when setting a small bitrate like 10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock = 30MHZ): | root@imx6ul7d:~# ip link set can0 up type can bitrate 10000 A link change request failed with some changes committed already. Interface can0 may have been left with an inconsistent configuration, please check. | RTNETLINK answers: Connection timed out It is caused by calling of flexcan_chip_unfreeze() timeout. Originally the code is using usleep_range(10, 20) for unfreeze operation, but the patch (8badd65 can: flexcan: avoid calling usleep_range from interrupt context) changed it into udelay(10) which is only a half delay of before, there're also some other delay changes. After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue. Meanwhile, Rasmus Villemoes reported that even with a timeout of 100, flexcan_probe() fails on the MPC8309, which requires a value of at least 140 to work reliably. 250 works for everyone. Signed-off-by: Joakim Zhang Reviewed-by: Dong Aisheng Cc: linux-stable Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

can: xilinx_can: use correct bittiming_const for CAN FD core

2019-06-25T03:34:53Z

commit 904044dd8fff43e289c11a2f90fa532e946a1d8b upstream. Commit 9e5f1b273e6a ("can: xilinx_can: add support for Xilinx CAN FD core") added a new can_bittiming_const structure for CAN FD cores that support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN cores, but the commit did not actually take that into use. Fix that. Tested with CAN FD core on a ZynqMP board. Fixes: 9e5f1b273e6a ("can: xilinx_can: add support for Xilinx CAN FD core") Reported-by: Shubhrajyoti Datta Signed-off-by: Anssi Hannula Cc: Michal Simek Reviewed-by: Shubhrajyoti Datta Cc: linux-stable Signed-off-by: Marc Kleine-Budde Signed-off-by: Greg Kroah-Hartman

net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set

2019-06-25T03:34:51Z

[ Upstream commit ceae266bf0ae6564ac16d086bf749a096fa90ded ] There's some NICs, such as hinic, with NETIF_F_IP_CSUM and NETIF_F_TSO on but NETIF_F_HW_CSUM off. And ipvlan device features will be NETIF_F_TSO on with NETIF_F_IP_CSUM and NETIF_F_IP_CSUM both off as IPVLAN_FEATURES only care about NETIF_F_HW_CSUM. So TSO will be disabled in netdev_fix_features. For example: Features for enp129s0f0: rx-checksumming: on tx-checksumming: on tx-checksum-ipv4: on tx-checksum-ip-generic: off [fixed] tx-checksum-ipv6: on Fixes: a188222b6ed2 ("net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK") Signed-off-by: Miaohe Lin Signed-off-by: David S. Miller Signed-off-by: Sasha Levin