user/sven/linux.git/drivers/phy, branch v4.14.15

phy: work around 'phys' references to usb-nop-xceiv devices

2018-01-23T18:58:16Z

commit b7563e2796f8b23c98afcfea7363194227fa089d upstream. Stefan Wahren reports a problem with a warning fix that was merged for v4.15: we had lots of device nodes with a 'phys' property pointing to a device node that is not compliant with the binding documented in Documentation/devicetree/bindings/phy/phy-bindings.txt This generally works because USB HCD drivers that support both the generic phy subsystem and the older usb-phy subsystem ignore most errors from phy_get() and related calls and then use the usb-phy driver instead. However, it turns out that making the usb-nop-xceiv device compatible with the generic-phy binding changes the phy_get() return code from -EINVAL to -EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns -EPROBE_DEFER from its probe function rather than ignoring the failure, breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is enabled. The same code is used in the dwc3 driver and the usb_add_hcd() function, so a reasonable assumption would be that many other platforms are affected as well. I have reviewed all the related patches and concluded that "usb-nop-xceiv" is the only USB phy that is affected by the change, and since it is by far the most commonly referenced phy, all the other USB phy drivers appear to be used in ways that are are either safe in DT (they don't use the 'phys' property), or in the driver (they already ignore -EPROBE_DEFER from generic-phy when usb-phy is available). To work around the problem, this adds a special case to _of_phy_get() so we ignore any PHY node that is compatible with "usb-nop-xceiv", as we know that this can never load no matter how much we defer. In the future, we might implement a generic-phy driver for "usb-nop-xceiv" and then remove this workaround. Since we generally want older kernels to also want to work with the fixed devicetree files, it would be good to backport the patch into stable kernels as well (3.13+ are possibly affected), even though they don't contain any of the patches that may have caused regressions. Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2 Link: https://patchwork.kernel.org/patch/10158145/ Cc: Felipe Balbi Cc: Eric Anholt Tested-by: Stefan Wahren Acked-by: Rob Herring Tested-by: Hans Verkuil Acked-by: Kishon Vijay Abraham I Signed-off-by: Arnd Bergmann Signed-off-by: Greg Kroah-Hartman

phy: tegra: fix device-tree node lookups

2018-01-02T19:31:15Z

commit 046046737bd35bed047460f080ea47e186be731e upstream. Fix child-node lookups during probe, which ended up searching the whole device tree depth-first starting at the parents rather than just matching on their children. To make things worse, some parent nodes could end up being being prematurely freed (by tegra_xusb_pad_register()) as of_find_node_by_name() drops a reference to its first argument. Fixes: 53d2a715c240 ("phy: Add Tegra XUSB pad controller support") Cc: Thierry Reding Signed-off-by: Johan Hovold Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Greg Kroah-Hartman

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

phy: rockchip-typec: Check for errors from tcphy_phy_init()

2017-10-03T09:48:41Z

The function tcphy_phy_init() could return an error but the callers weren't checking the return value. They should. In at least one case while testing I saw the message "wait pma ready timeout" which indicates that tcphy_phy_init() really could return an error and we should account for it. Signed-off-by: Douglas Anderson Reviewed-by: Guenter Roeck Signed-off-by: Kishon Vijay Abraham I

phy: rockchip-typec: Don't set the aux voltage swing to 400 mV

2017-09-26T11:32:49Z

On rk3399-gru-kevin there are some cases where we're seeing AUX CH failures when trying to do DisplayPort over type C. Problems are intermittent and don't reproduce all the time. Problems are often bursty and failures persist for several seconds before going away. The failure case I focused on is: * A particular type C to HDMI adapter. * One orientation (flip mode) of that adapter. * Easier to see failures when something is plugged into the _other type C port at the same time. * Problems reproduce on both type C ports (left and right side). Ironically problems also stop reproducing when I solder wires onto the AUX CH signals on a port (even if no scope is connected to the signals). In this case, problems only stop reproducing on the port with the wires connected. From the above it appears that something about the signaling on the aux channel is marginal and any slight differences can bring us over the edge to failure. It turns out that we can fix our problems by just increasing the voltage swing of the AUX CH, giving us a bunch of extra margin. In DP up to version 1.2 the voltage swing on the aux channel was specced as .29 V to 1.38 V. In DP version 1.3 the aux channel voltage was tightened to be between .29 V and .40 V, but it clarifies that it really only needs the lower voltage when operating at the highest speed (HBR3 mode). So right now we are trying to use a voltage that technically should be valid for all versions of the spec (including version 1.3 when transmitting at HBR3). That would be great to do if it worked reliably. ...but it doesn't seem to. It turns out that if you continue to read through the DP part of the rk3399 TRM and other parts of the type C PHY spec you'll find out that while the rk3399 does support DP 1.3, it doesn't support HBR3. The docs specifically say "RBR, HBR and HBR2 data rates only". Thus there is actually no requirement to support an AUX CH swing of .4 V. Even if there is no actual requirement to support the tighter voltage swing, one could possibly argue that we should support it anyway. The DP spec clarifies that the lower voltage on the AUX CH will reduce cross talk in some cases and that seems like it could be beneficial even at the lower bit rates. At the moment, though, we are seeing problems with the AUX CH and not on the other lines. Also, checking another known working and similar laptop shows that the other laptop runs the AUX channel at a higher voltage. Other notes: * Looking at measurements done on the AUX CH we weren't actually compliant with the DP 1.3 spec anyway. AUX CH peek-to-peek voltage was measured on rk3399-gru-kevin as .466 V which is > .4 V. * With this new patch the AUX channel isn't actually 1.0 V, but it has been confirmed that the signal is better and has more margin. Eye diagram passes. * If someone were truly an expert in the Type C PHY and in DisplayPort signaling they might be able to make things work and keep the voltage at < .4 V. The Type C PHY seems to have a plethora of tuning knobs that could almost certainly improve the signal integrity. Some of these things (like enabling tx_fcm_full_margin) even seem to fix my problems. However, lacking expertise I can't say whether this is a better or worse solution. Tightening signals to give cleaner waveforms can often have adverse affects, like increasing EMI or adding noise to other signals. I'd rather not tune things like this without a healthy application of expertise that I don't have. Signed-off-by: Douglas Anderson Signed-off-by: Kishon Vijay Abraham I

phy: rockchip-typec: Set the AUX channel flip state earlier

2017-09-26T11:32:49Z

On some DP monitors we found that setting the wrong flip state on the AUX channel could cause the monitor to stop asserting HotPlug Detect (HPD). Setting the right flip state caused these monitors to start asserting HotPlug Detect again. Here's what we believe was happening: * We'd plug in the monitor and we'd see HPD assert * We'd quickly see HPD deassert * The kernel would try to init the type C PHY but would init it in USB mode (because there was a peripheral there but no HPD) * Because the kernel never set the flip mode properly we'd never see the HPD come back. With this change, we'll still see HPD disappear (we don't think there's anything we can do about that), but then it will come back. Overall we can say that it's sane to set the AUX channel flip state even when HPD is not asserted. NOTE: to make this change possible, I needed to do a bit of cleanup to the tcphy_dp_aux_calibration() function so that it doesn't ever clobber the FLIP state. This made it very obvious that a line of code documented as "setting bit 12" also did a bunch of other magic, undocumented stuff. For now I'll just break out the bits and add a comment that this is black magic and we'll try to document tcphy_dp_aux_calibration() better in a future CL. ALSO NOTE: the old function used to write a bunch of hardcoded values in _some_ cases instead of doing a read-modify-write. One could possibly assert that these could have had (beneficial) side effects and thus with this new code (which always does read-modify-write) we could have a bug. We shouldn't need to worry, though, since in the old code tcphy_dp_aux_calibration() was always called following the de-assertion of "reset" the the type C PHY. ...so the type C PHY was always in default state. TX_ANA_CTRL_REG_1 is documented to be 0x0 after reset. This was also confirmed by printk. Suggested-by: Shawn Nematbakhsh Reviewed-by: Chris Zhong Signed-off-by: Douglas Anderson Signed-off-by: Kishon Vijay Abraham I

phy: mvebu-cp110: checking for NULL instead of IS_ERR()

2017-09-26T11:32:49Z

devm_ioremap_resource() never returns NULL, it only returns error pointers so this test needs to be changed. Fixes: d0438bd6aa09 ("phy: add the mvebu cp110 comphy driver") Signed-off-by: Dan Carpenter Signed-off-by: Kishon Vijay Abraham I

phy: mvebu-cp110-comphy: explicitly set the pipe selector

2017-09-26T11:32:49Z

The pipe selector is used to select some modes (such as USB or PCIe). Otherwise it must be set to 0 (or "unconnected"). This patch does this to ensure it is not set to an incompatible value when using the supported modes (SGMII, 10GKR). Signed-off-by: Antoine Tenart Signed-off-by: Kishon Vijay Abraham I

phy: mvebu-cp110-comphy: fix mux error check

2017-09-26T11:32:48Z

The mux value is retrieved from the mvebu_comphy_get_mux() function which returns an int. In mvebu_comphy_power_on() this int is stored to a u32 and a check is made to ensure it's not negative. Which is wrong. This fixes it. Fixes: d0438bd6aa09 ("phy: add the mvebu cp110 comphy driver") Signed-off-by: Antoine Tenart Signed-off-by: Kishon Vijay Abraham I

phy: phy-mtk-tphy: fix NULL point of chip bank

2017-09-26T11:32:48Z

Chip bank of version-1 is initialized as NULL, but it's used by pcie_phy_instance_power_on/off(), so assign it a right address. Signed-off-by: Chunfeng Yun Signed-off-by: Kishon Vijay Abraham I