user/sven/linux.git/drivers/rtc/class.c, branch v3.8.4

revert "rtc: recycle id when unloading a rtc driver"

2012-12-21T01:40:20Z

Revert commit 2830a6d20139df2198d63235df7957712adb28e5. We already perform the ida_simple_remove() in rtc_device_release(), which is an appropriate place. Commit 2830a6d20 ("rtc: recycle id when unloading a rtc driver") caused the kernel to emit ida_remove called for id=0 which is not allocated. warnings when rtc_device_release() tries to release an alread-released ID. Let's restore things to their previous state and then work out why Vincent's kernel wasn't calling rtc_device_release() - presumably a bug in a specific sub-driver. Reported-by: Lothar Waßmann Acked-by: Alexander Holler Cc: Vincent Palatin Cc: [3.7.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

rtc_sysfs_show_hctosys(): display 0 if resume failed

2012-10-05T18:05:04Z

Without this patch /sys/class/rtc/$CONFIG_RTC_HCTOSYS_DEVICE/hctosys contains a 1 (meaning "This rtc was used to initialize the system clock") even if setting the time by do_settimeofday() at bootup failed. The RTC can also be used to set the clock on resume, if it did 1, otherwise 0. Previously there was no indication if the RTC was used to set the clock in resume. This uses only CONFIG_RTC_HCTOSYS_DEVICE for conditional compilation instead of it and CONFIG_RTC_HCTOSYS to be more consistent. rtc_hctosys_ret was moved to class.c so class.c no longer depends on hctosys.c. [sfr@canb.auug.org.au: fix build] Signed-off-by: David Fries Cc: Matthew Garrett Cc: Alessandro Zummo Cc: Uwe Kleine-König Signed-off-by: Stephen Rothwell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

rtc: recycle id when unloading a rtc driver

2012-10-05T18:05:02Z

When calling rtc_device_unregister, we are not freeing the id used by the driver. So when doing a unload/load cycle for a RTC driver (e.g. rmmod rtc_cmos && modprobe rtc_cmos), its id is incremented by one. As a consequence, we no longer have neither an rtc0 driver nor a /proc/driver/rtc (as it only exists for the first driver). Signed-off-by: Vincent Palatin Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2011-12-06T00:53:43Z

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clockevents: Set noop handler in clockevents_exchange_device() tick-broadcast: Stop active broadcast device when replacing it clocksource: Fix bug with max_deferment margin calculation rtc: Fix some bugs that allowed accumulating time drift in suspend/resume rtc: Disable the alarm in the hardware

rtc: Fix some bugs that allowed accumulating time drift in suspend/resume

2011-11-23T03:25:56Z

The current code checks if abs(delta_delta.tv_sec) is greater or equal to two before it discards the old delta value, but this can trigger at close to -1 seconds since -1.000000001 seconds is stored as tv_sec -2 and tv_nsec 999999999 in a normalized timespec. rtc_resume had an early return check if the rtc value had not changed since rtc_suspend. This effectivly stops time for the duration of the short sleep. Check if sleep_time is positive after all the adjustments have been applied instead since this allows the old_system adjustment in rtc_suspend to have an effect even for short sleep cycles. CC: stable@kernel.org Signed-off-by: Arve Hjønnevåg Signed-off-by: John Stultz

drivers/rtc/class.c: convert idr to ida and use ida_simple_get()

2011-11-02T23:06:58Z

This is the one use of an ida that doesn't retry on receiving -EAGAIN. I'm assuming do so will cause no harm and may help on a rare occasion. Signed-off-by: Jonathan Cameron Cc: Alessandro Zummo Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

rtc: Avoid accumulating time drift in suspend/resume

2011-06-21T23:55:39Z

Because the RTC interface is only a second granular interface, each time we read from the RTC for suspend/resume, we introduce a half second (on average) of error. In order to avoid this error accumulating as the system is suspended over and over, this patch measures the time delta between the RTC and the system CLOCK_REALTIME. If the delta is less then 2 seconds from the last suspend, we compensate by using the previous time delta (keeping it close). If it is larger then 2 seconds, we assume the clock was set or has been changed, so we do no correction and update the delta. Note: If NTP is running, ths could seem to "fight" with the NTP corrected time, where as if the system time was off by 1 second, and NTP slewed the value in, a suspend/resume cycle could undo this correction, by trying to restore the previous offset from the RTC. However, without this patch, since each read could cause almost a full second worth of error, its possible to get almost 2 seconds of error just from the suspend/resume cycle alone, so this about equal to any offset added by the compensation. Further on systems that suspend/resume frequently, this should keep time closer then NTP could compensate for if the errors were allowed to accumulate. Credits to Arve Hjønnevåg for suggesting this solution. This patch also improves some of the variable names and adds more clear comments. CC: Arve Hjønnevåg CC: Thomas Gleixner Signed-off-by: John Stultz

time: Add timekeeping_inject_sleeptime

2011-04-26T21:01:41Z

Some platforms cannot implement read_persistent_clock, as their RTC devices are only accessible when interrupts are enabled. This keeps them from being used by the timekeeping code on resume to measure the time in suspend. The RTC layer tries to work around this, by calling do_settimeofday on resume after irqs are reenabled to set the time properly. However, this only corrects CLOCK_REALTIME, and does not properly adjust the sleep time value. This causes btime in /proc/stat to be incorrect as well as making the new CLOCK_BOTTTIME inaccurate. This patch resolves the issue by introducing a new timekeeping hook to allow the RTC layer to inject the sleep time on resume. The code also checks to make sure that read_persistent_clock is nonfunctional before setting the sleep time, so that should the RTC's HCTOSYS option be configured in on a system that does support read_persistent_clock we will not increase the total_sleep_time twice. CC: Arve Hjønnevåg CC: Thomas Gleixner Acked-by: Arnd Bergmann Signed-off-by: John Stultz

RTC: Fix early irqs caused by calling rtc_set_alarm too early

2011-03-30T01:44:05Z

When we register an rtc device at boot, we read the alarm value in hardware and set the rtc device's aie_timer to that value. The initial method to do this was to simply call rtc_set_alarm() with the value read from hardware. However, this may cause problems as rtc_set_alarm may enable interupts, and the RTC alarm might fire, which can cause invalid pointer dereferencing since the RTC registration is not complete. This patch solves the issue by initializing the rtc_device.aie_timer y hand via rtc_initialize_alarm(). This avoids any calls to the RTC hardware which might enable interrupts too early. CC: Thomas Gleixner CC: Alessandro Zummo Reported-by: Konrad Rzeszutek Wilk Tested-by: Konrad Rzeszutek Wilk Signed-off-by: John Stultz

RTC: Initialize kernel state from RTC

2011-03-09T19:22:50Z

Mark Brown pointed out a corner case: that RTC alarms should be allowed to be persistent across reboots if the hardware supported it. The rework of the generic layer to virtualize the RTC alarm virtualized much of the alarm handling, and removed the code used to read the alarm time from the hardware. Mark noted if we want the alarm to be persistent across reboots, we need to re-read the alarm value into the virtualized generic layer at boot up, so that the generic layer properly exposes that value. This patch restores much of the earlier removed rtc_read_alarm code and wires it in so that we set the kernel's alarm value to what we find in the hardware at boot time. NOTE: Not all hardware supports persistent RTC alarm state across system reset. rtc-cmos for example will keep the alarm time, but disables the AIE mode irq. Applications should not expect the RTC alarm to be valid after a system reset. We will preserve what we can, to represent the hardware state at boot, but its not guarenteed. Further, in the future, with multiplexed RTC alarms, the soonest alarm to fire may not be the one set via the /dev/rt ioctls. So an application may set the alarm with RTC_ALM_SET, but after a reset find that RTC_ALM_READ returns an earlier time. Again, we preserve what we can, but applications should not expect the RTC alarm state to persist across a system reset. Big thanks to Mark for pointing out the issue! Thanks also to Marcelo for helping think through the solution. CC: Mark Brown CC: Marcelo Roberto Jimenez CC: Thomas Gleixner CC: Alessandro Zummo CC: rtc-linux@googlegroups.com Reported-by: Mark Brown Signed-off-by: John Stultz