user/sven/linux.git/drivers/tc, branch v5.2.5

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46Z

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

TC: Set DMA masks for devices

2018-10-11T16:16:44Z

Fix a TURBOchannel support regression with commit 205e1b7f51e4 ("dma-mapping: warn when there is no coherent_dma_mask") that caused coherent DMA allocations to produce a warning such as: defxx: v1.11 2014/07/01 Lawrence V. Stefani and others tc1: DEFTA at MMIO addr = 0x1e900000, IRQ = 20, Hardware addr = 08-00-2b-a3-a3-29 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 dfx_dev_register+0x670/0x678 Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #2 Stack : ffffffff8009ffc0 fffffffffffffec0 0000000000000000 ffffffff80647650 0000000000000000 0000000000000000 ffffffff806f5f80 ffffffffffffffff 0000000000000000 0000000000000000 0000000000000001 ffffffff8065d4e8 98000000031b6300 ffffffff80563478 ffffffff805685b0 ffffffffffffffff 0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8 0000000000000000 0000000000000009 ffffffff8053efd0 ffffffff806657d0 0000000000000000 ffffffff803177f8 0000000000000000 ffffffff806d0000 9800000003078000 980000000307b9e0 000000001e900000 ffffffff80067940 0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8 ffffffff805176c0 ffffffff8004dc78 0000000000000000 ffffffff80067940 ... Call Trace: [] show_stack+0xa0/0x130 [] __warn+0x128/0x170 ---[ end trace b1d1e094f67f3bb2 ]--- This is because the TURBOchannel bus driver fails to set the coherent DMA mask for devices enumerated. Set the regular and coherent DMA masks for TURBOchannel devices then, observing that the bus protocol supports a 34-bit (16GiB) DMA address space, by interpreting the value presented in the address cycle across the 32 `ad' lines as a 32-bit word rather than byte address[1]. The architectural size of the TURBOchannel DMA address space exceeds the maximum amount of RAM any actual TURBOchannel system in existence may have, hence both masks are the same. This removes the warning shown above. References: [1] "TURBOchannel Hardware Specification", EK-369AA-OD-007B, Digital Equipment Corporation, January 1993, Section "DMA", pp. 1-15 -- 1-17 Signed-off-by: Maciej W. Rozycki Signed-off-by: Paul Burton Patchwork: https://patchwork.linux-mips.org/patch/20835/ Fixes: 205e1b7f51e4 ("dma-mapping: warn when there is no coherent_dma_mask") Cc: stable@vger.kernel.org # 4.16+ Cc: Ralf Baechle

TC: Error handling clean-ups

2014-11-24T06:45:25Z

Rewrite TURBOchannel error handling to use a common failure path, making sure put_device is called for devices that failed initialization. While at it update printk calls to use pr_err rather than KERN_ERR. Signed-off-by: Maciej W. Rozycki Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/6701/ Signed-off-by: Ralf Baechle

TC: Handle device_register() errors.

2014-06-26T09:48:23Z

Make the TURBOchannel driver bail out if the call to device_register() failed. Signed-off-by: Levente Kurusa Acked-by: Maciej W. Rozycki Cc: LKML Cc: Linux MIPS Patchwork: https://patchwork.linux-mips.org/patch/6673/ Signed-off-by: Ralf Baechle

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

2010-03-30T13:02:32Z

percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo Guess-its-ok-by: Christoph Lameter Cc: Ingo Molnar Cc: Lee Schermerhorn

tc: struct device - replace bus_id with dev_name(), dev_set_name()

2009-03-24T23:38:22Z

Cc: macro@linux-mips.org Acked-by: Greg Kroah-Hartman Signed-off-by: Kay Sievers

lk201: remove obsolete driver

2007-10-17T15:42:57Z

Remove the old-fashioned lk201 driver under drivers/tc/ that used to be used by the old dz.c and zs.c drivers, which is now orphan code referred to from nowhere and does not build anymore. A modern replacement is available as drivers/input/keyboard/lkkbd.c. There are no plans to do anything about this piece of code and it does not fit anywhere anymore, so it is not just a matter of maintenance or the lack of. There are still some bits that might be added to the new lkkbd.c driver based on the old code, and the embedded hardware documentation which is otherwise quite hard to get hold of might be useful to keep too. Both of these can be done separately though. RIP. Signed-off-by: Maciej W. Rozycki Acked-by: Ralf Baechle Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

unicode diacritics support

2007-10-17T15:42:52Z

There have been issues with non-latin1 diacritics and unicode. http://bugzilla.kernel.org/show_bug.cgi?id=7746 Git 759448f459234bfcf34b82471f0dba77a9aca498 `Kernel utf-8 handling' partly resolved it by adding conversion between diacritics and unicode. The patch below goes further by just turning diacritics into unicode, hence providing better future support. The kbd support can be fetched from http://bugzilla.kernel.org/attachment.cgi?id=12313 This was tested in all of latin1, latin9, latin2 and unicode with french and czech dead keys. Turn the kernel accent_table into unicode, and extend ioctls KDGKBDIACR and KDSKBDIACR into their equivalents KDGKBDIACRUC and KDSKBDIACR. New function int conv_uni_to_8bit(u32 uni) for converting unicode into 8bit _input_. No, we don't want to store the translation, as it is potentially sparse and large. Signed-off-by: Samuel Thibault Cc: Jan Engelhardt Cc: "Antonino A. Daplas" Cc: David Woodhouse Cc: Martin Schwidefsky Cc: Heiko Carstens Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

zs: move to the serial subsystem

2007-07-18T15:38:22Z

This is a reimplementation of the zs driver for the serial subsystem. Any resemblance to the old driver is purely coincidential. ;-) I do hope I got the handling of modem lines right -- better do not tackle me about the issue unless you feel too good... Any users of the old driver: please note the numbers of the serial lines have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has to do with the modem lines mentioned above; basically the port A in a given chip has to be initialised before the port B if you want to use the latter as the serial console (which is usually the case), as operations on modem lines of the serial line associated with the port B access both ports (see the comment at the top of the driver for the details of wiring used). Please update your scripts. This is also the reason each SCC now requests an IRQ once only (as seen in "/proc/interrupts") -- the handler takes care of both ports at once as the line associated with the port B has to take status update interrupts from both ports (and yet the line of the port A takes its own for itself too). The old driver never got it right... Signed-off-by: Maciej W. Rozycki Cc: Ralf Baechle Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[MIPS] DEC: Fix modpost warning.

2007-07-12T16:41:07Z

LD vmlinux SYSMAP System.map SYSMAP .tmp_System.map MODPOST vmlinux WARNING: drivers/built-in.o(.data+0x2480): Section mismatch: reference to .init.text: (between 'sercons' and 'ds_parms') Signed-off-by: Ralf Baechle