user/sven/linux.git/drivers/tty, branch v4.19.170

serial_core: Check for port state when tty is in error state

2020-12-30T10:25:48Z

commit 2f70e49ed860020f5abae4f7015018ebc10e1f0e upstream. At the moment opening a serial device node (such as /dev/ttyS3) succeeds even if there is no actual serial device behind it. Reading/writing/ioctls fail as expected because the uart port is not initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state bit is set fot the tty. However setting line discipline does not have these checks 8250_port.c (8250 is the default choice made by univ8250_console_init()). As the result of PORT_UNKNOWN, uart_port::iobase is NULL which a platform translates onto some address accessing which produces a crash like below. This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash. Found by syzkaller. Signed-off-by: Alexey Kardashevskiy Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access

2020-12-30T10:25:43Z

commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream. It has been observed that once per 300-1300 port openings the first transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared as "e" on the wire). It only happened if single byte has been transmitted right after port open, which means, DMA is not used for this transfer and the corruption never happened afterwards. Therefore I've carefully re-read the MDR1 errata (link below), which says "when accessing the MDR1 registers that causes a dummy under-run condition that will freeze the UART in IrDA transmission. In UART mode, this may corrupt the transferred data". Strictly speaking, omap_8250_mdr1_errataset() performs a read access and if the value is the same as should be written, exits without errata-recommended FIFO reset. A brief check of the serial_omap_mdr1_errataset() from the competing omap-serial driver showed it has no read access of MDR1. After removing the read access from omap_8250_mdr1_errataset() the data corruption never happened any more. Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com Signed-off-by: Greg Kroah-Hartman

tty: Fix ->session locking

2020-12-11T12:25:01Z

commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream. Currently, locking of ->session is very inconsistent; most places protect it using the legacy tty mutex, but disassociate_ctty(), __do_SAK(), tiocspgrp() and tiocgsid() don't. Two of the writers hold the ctrl_lock (because they already need it for ->pgrp), but __proc_set_tty() doesn't do that yet. On a PREEMPT=y system, an unprivileged user can theoretically abuse this broken locking to read 4 bytes of freed memory via TIOCGSID if tiocgsid() is preempted long enough at the right point. (Other things might also go wrong, especially if root-only ioctls are involved; I'm not sure about that.) Change the locking on ->session such that: - tty_lock() is held by all writers: By making disassociate_ctty() hold it. This should be fine because the same lock can already be taken through the call to tty_vhangup_session(). The tricky part is that we need to shorten the area covered by siglock to be able to take tty_lock() without ugly retry logic; as far as I can tell, this should be fine, since nothing in the signal_struct is touched in the `if (tty)` branch. - ctrl_lock is held by all writers: By changing __proc_set_tty() to hold the lock a little longer. - All readers that aren't holding tty_lock() hold ctrl_lock: By adding locking to tiocgsid() and __do_SAK(), and expanding the area covered by ctrl_lock in tiocspgrp(). Cc: stable@kernel.org Signed-off-by: Jann Horn Reviewed-by: Jiri Slaby Signed-off-by: Greg Kroah-Hartman

tty: Fix ->pgrp locking in tiocspgrp()

2020-12-11T12:25:00Z

commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream. tiocspgrp() takes two tty_struct pointers: One to the tty that userspace passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`). These pointers are different when ioctl() is called with a master fd. To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock. This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on both sides of a PTY pair to corrupt the refcount of `struct pid`, leading to use-after-free errors. Fixes: 47f86834bbd4 ("redo locking of tty->pgrp") CC: stable@kernel.org Signed-off-by: Jann Horn Reviewed-by: Jiri Slaby Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: keep console clocks always on

2020-11-24T12:27:24Z

commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream. For below code, there has chance to cause deadlock in SMP system: Thread 1: clk_enable_lock(); pr_info("debug message"); clk_enable_unlock(); Thread 2: imx_uart_console_write() clk_enable() clk_enable_lock(); Thread 1: Acuired clk enable_lock -> printk -> console_trylock_spinning Thread 2: console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock So the patch is to keep console port clocks always on like other console drivers. Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check") Acked-by: Uwe Kleine-König Signed-off-by: Fugang Duan Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com Cc: stable [fix up build warning - gregkh] Signed-off-by: Greg Kroah-Hartman

serial: txx9: add missing platform_driver_unregister() on error in serial_txx9_init

2020-11-10T11:36:00Z

commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream. Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable Signed-off-by: Greg Kroah-Hartman

serial: 8250_mtk: Fix uart_get_baud_rate warning

2020-11-10T11:36:00Z

commit 912ab37c798770f21b182d656937072b58553378 upstream. Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable Signed-off-by: Greg Kroah-Hartman

vt: Disable KD_FONT_OP_COPY

2020-11-10T11:36:00Z

commit 3c4e0dff2095c579b142d5a0693257f1c58b4804 upstream. It's buggy: On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote: > We recently discovered a slab-out-of-bounds read in fbcon in the latest > kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that > "fbcon_do_set_font" did not handle "vc->vc_font.data" and > "vc->vc_font.height" correctly, and the patch > for VT_RESIZEX can't handle this > issue. > > Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and > use KD_FONT_OP_SET again to set a large font.height for tty1. After that, > we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data > in "fbcon_do_set_font", while tty1 retains the original larger > height. Obviously, this will cause an out-of-bounds read, because we can > access a smaller vc_font.data with a larger vc_font.height. Further there was only one user ever. - Android's loadfont, busybox and console-tools only ever use OP_GET and OP_SET - fbset documentation only mentions the kernel cmdline font: option, not anything else. - systemd used OP_COPY before release 232 published in Nov 2016 Now unfortunately the crucial report seems to have gone down with gmane, and the commit message doesn't say much. But the pull request hints at OP_COPY being broken https://github.com/systemd/systemd/pull/3651 So in other words, this never worked, and the only project which foolishly every tried to use it, realized that rather quickly too. Instead of trying to fix security issues here on dead code by adding missing checks, fix the entire thing by removing the functionality. Note that systemd code using the OP_COPY function ignored the return value, so it doesn't matter what we're doing here really - just in case a lone server somewhere happens to be extremely unlucky and running an affected old version of systemd. The relevant code from font_copy_to_all_vcs() in systemd was: /* copy font from active VT, where the font was uploaded to */ cfo.op = KD_FONT_OP_COPY; cfo.height = vcs.v_active-1; /* tty1 == index 0 */ (void) ioctl(vcfd, KDFONTOP, &cfo); Note this just disables the ioctl, garbage collecting the now unused callbacks is left for -next. v2: Tetsuo found the old mail, which allowed me to find it on another archive. Add the link too. Acked-by: Peilin Ye Reported-by: Minh Yuan References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html References: https://github.com/systemd/systemd/pull/3651 Cc: Greg KH Cc: Peilin Ye Cc: Tetsuo Handa Signed-off-by: Daniel Vetter Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman

tty: make FONTX ioctl use the tty pointer they were actually passed

2020-11-05T10:08:54Z

commit 90bfdeef83f1d6c696039b6a917190dcbbad3220 upstream. Some of the font tty ioctl's always used the current foreground VC for their operations. Don't do that then. This fixes a data race on fg_console. Side note: both Michael Ellerman and Jiri Slaby point out that all these ioctls are deprecated, and should probably have been removed long ago, and everything seems to be using the KDFONTOP ioctl instead. In fact, Michael points out that it looks like busybox's loadfont program seems to have switched over to using KDFONTOP exactly _because_ of this bug (ahem.. 12 years ago ;-). Reported-by: Minh Yuan Acked-by: Michael Ellerman Acked-by: Jiri Slaby Cc: Greg KH Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman

vt: keyboard, extend func_buf_lock to readers

2020-11-05T10:08:50Z

commit 82e61c3909db51d91b9d3e2071557b6435018b80 upstream. Both read-side users of func_table/func_buf need locking. Without that, one can easily confuse the code by repeatedly setting altering strings like: while (1) for (a = 0; a < 2; a++) { struct kbsentry kbs = {}; strcpy((char *)kbs.kb_string, a ? ".\n" : "88888\n"); ioctl(fd, KDSKBSENT, &kbs); } When that program runs, one can get unexpected output by holding F1 (note the unxpected period on the last line): . 88888 .8888 So protect all accesses to 'func_table' (and func_buf) by preexisting 'func_buf_lock'. It is easy in 'k_fn' handler as 'puts_queue' is expected not to sleep. On the other hand, KDGKBSENT needs a local (atomic) copy of the string because copy_to_user can sleep. Use already allocated, but unused 'kbs->kb_string' for that purpose. Note that the program above needs at least CAP_SYS_TTY_CONFIG. This depends on the previous patch and on the func_buf_lock lock added in commit 46ca3f735f34 (tty/vt: fix write/write race in ioctl(KDSKBSENT) handler) in 5.2. Likely fixes CVE-2020-25656. Cc: Reported-by: Minh Yuan Signed-off-by: Jiri Slaby Link: https://lore.kernel.org/r/20201019085517.10176-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman