user/sven/linux.git/drivers/usb/misc/usbtest.c, branch v3.18.22

usb: hub: rename khubd to hub_wq in documentation and comments

2014-09-24T05:33:19Z

USB hub has started to use a workqueue instead of kthread. Let's update the documentation and comments here and there. This patch mostly just replaces "khubd" with "hub_wq". There are only few exceptions where the whole sentence was updated. These more complicated changes can be found in the following files: Documentation/usb/hotplug.txt drivers/net/usb/usbnet.c drivers/usb/core/hcd.c drivers/usb/host/ohci-hcd.c drivers/usb/host/xhci.c Signed-off-by: Petr Mladek Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

usbtest: Add interrupt EP testcases

2014-08-29T20:51:11Z

Two simple test cases for interrupt endpoints are added to the usbtest.c file. These are simple non-queued interrupt IN and interrupt OUT transfers. Currently, only gadget zero is capable of executing the interrupt EP test cases. However, extending the same to other gadgets is extremely simple and can be done on-demand. The two new tests added are - Test 25: To verify Interrupt OUT transfer - Test 26: To verify Interrupt IN transfer Since the default value of wMaxPacketSize is set as 1024, so interrupt IN transfers must be specified with the size parameter = multiple of 1024. Otherwise the default value (512) in the usbtest application fails the transfer. See [RUN 4] for sample logs The application logs (usbtest) and corresponding kernel logs are as following: [Run 1] ./testusb -a -c 10 -s 2048 -t 26 -v 511 usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times [Run 2] ./testusb -a -c 10 -s 1024 -t 25 -v 511 usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times [Run 3] ./testusb -a -c 10 -s 1098 -t 25 -v 511 usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times [Run 4 - Failure case scenario] ./testusb -a -t 26 unknown speed /dev/bus/usb/007/004 0 /dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type) usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times usb 7-1: test26 failed, iterations left 999, status -75 (not 0) Signed-off-by: Amit Virdi Signed-off-by: Felipe Balbi

USB: usbtest: add a timeout for scatter-gather tests

2014-06-18T00:05:50Z

In usbtest, tests 5 - 8 use the scatter-gather library in usbcore without any sort of timeout. If there's a problem in the gadget or host controller being tested, the test can hang. This patch adds a 10-second timeout to the tests, so that they will fail gracefully with an ETIMEDOUT error instead of hanging. Signed-off-by: Alan Stern Reported-by: Huang Rui Tested-by: Huang Rui CC: Signed-off-by: Greg Kroah-Hartman

usb: usbtest: add pattern check on pipe in phase of unlink read

2014-05-27T23:23:43Z

TEST 11 unlinks the URB read request for N times. When host and gadget both initialize pattern 1 (mod 63) data series to do IN transfer, the host side function should check the data buffer if it is as mod 63 series, because the data packet which host receivced will follow pattern 1. So this patch adds this checking action. Signed-off-by: Huang Rui Signed-off-by: Greg Kroah-Hartman

usb: usbtest: fix unlink write error with pattern 1

2014-05-27T23:23:43Z

TEST 12 and TEST 24 unlinks the URB write request for N times. When host and gadget both initialize pattern 1 (mod 63) data series to transfer, the gadget side will complain the wrong data which is not expected. Because in host side, usbtest doesn't fill the data buffer as mod 63 and this patch fixed it. [20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready [20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active [20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last [20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000 [20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0 [20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready [20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active [20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy [20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete [20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0 [20285.491431] zero gadget: bad OUT byte, buf[1] = 0 [20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000 [20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0 [20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512 [20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready [20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active [20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last [20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000 [20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0 Cc: Signed-off-by: Huang Rui Signed-off-by: Greg Kroah-Hartman

Merge tag 'for-usb-next-2013-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next

2013-12-21T23:58:40Z

Sarah writes: xhci: Cleanups, non-urgent fixes for 3.14. Happy Holidays, Greg! Here's four patches to be queued to usb-next for 3.14. One adds a module parameter to the xHCI driver to allow users to enable xHCI quirks without recompiling their kernel, which you've already said is fine. The second patch is a bug fix for new usbtest code that's only in usb-next. The third patch is simple cleanup. The last patch is a non-urgent bug fix for xHCI platform devices. The bug has been in the code since 3.9. You've been asking me to hold off on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and be backported to stable once 3.14 is out. These have all been tested over the past week. I did run across one oops, but it turned out to be a bug in 3.12, and therefore not related to any of these patches. Please queue these for usb-next and 3.14. Thanks, Sarah Sharp

usb: usbtest: Always clear halt else further tests will fail

2013-12-19T00:26:12Z

In test_halt() we set an endpoint halt condition and return on halt verification failure, then the enpoint will remain halted and all further tests related to that enpoint will fail. This is because we don't tackle endpoint halt error condition in any of the tests. To avoid that situation, make sure to clear the halt condition before exiting test_halt(). Signed-off-by: Roger Quadros Reviewed-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

usb: usbtest: Add timetout to simple_io()

2013-12-19T00:26:12Z

Without a timetout some tests e.g. test_halt() can remain stuck forever. Signed-off-by: Roger Quadros Reviewed-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

usbtest: Fix BOS control test for USB 2.01 devices.

2013-12-17T21:40:29Z

Commit c952a8ba7136505cd1ca01735cc748ddc08c7d2f "usb: usbtest: add a test case to support bos for queue control" will cause USB 2.01 and USB 2.10 devices with a BOS descriptor to fail case 15 of the control test. The Link PM errata (released in 2007, updated in 2011) says: "The value of the bcdUSB field in the standard USB 2.0 Device Descriptor is used to indicate that the device supports the request to read the BOS Descriptor (i.e. GetDescriptor(BOS)). Devices that support the BOS descriptor must have a bcdUSB value of 0201H or larger." The current code says that non-SuperSpeed devices *must* return -EPIPE, as this comment shows: /* sign of this variable means: * -: tested code must return this (negative) error code * +: tested code may return this (negative too) error code */ int expected = 0; This means the test will fail with USB 2.01 and USB 2.10 devices that provide a BOS descriptor. Change it to only require a stall response if the USB device bcdUSB is less than 2.01. Signed-off-by: Sarah Sharp Acked-by: Huang Rui

usb: usbtest: update bos test coverage to usb 2.1 device

2013-12-09T01:42:45Z

The commit "usb: usbtest: support bos descriptor test for usb 3.0" introduced a test for bos descriptor. And USB 2.1 device also can be checked. So this patch extends the test coverage to support USB 2.1 device. Reported-by: Sarah Sharp Signed-off-by: Huang Rui Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman