user/sven/linux.git/drivers/usb, branch v3.2.31

usb: gadget: dummy_hcd: fixup error probe path

2012-10-10T02:31:14Z

commit 1b68a4ca2d038addb7314211d122fb6d7002b38b upstream. If USB2 host controller probes fine but USB3 does not then we don't remove the USB controller properly and lock up the system while the HUB code will try to enumerate the USB2 controller and access memory which is no longer available in case the dummy_hcd was compiled as a module. This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.) if used in USB3 mode because dummy does not provide this descriptor and explodes later. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Felipe Balbi Signed-off-by: Ben Hutchings

USB: Fix race condition when removing host controllers

2012-10-10T02:31:07Z

commit 0d00dc2611abbe6ad244d50569c2ee82ce42846c upstream. This patch (as1607) fixes a race that can occur if a USB host controller is removed while a process is reading the /sys/kernel/debug/usb/devices file. The usb_device_read() routine uses the bus->root_hub pointer to determine whether or not the root hub is registered. The is not a valid test, because the pointer is set before the root hub gets registered and remains set even after the root hub is unregistered and deallocated. As a result, usb_device_read() or usb_device_dump() can access freed memory, causing an oops. The patch changes the test to use the hcd->rh_registered flag, which does get set and cleared at the appropriate times. It also makes sure to hold the usb_bus_list_lock mutex while setting the flag, so that usb_device_read() will become aware of new root hubs as soon as they are registered. Signed-off-by: Alan Stern Reported-by: Don Zickus Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

EHCI: Update qTD next pointer in QH overlay region during unlink

2012-09-19T14:05:20Z

commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream. There is a possibility of QH overlay region having reference to a stale qTD pointer during unlink. Consider an endpoint having two pending qTD before unlink process begins. The endpoint's QH queue looks like this. qTD1 --> qTD2 --> Dummy To unlink qTD2, QH is removed from asynchronous list and Asynchronous Advance Doorbell is programmed. The qTD1's next qTD pointer is set to qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell interrupt. If QH's current qTD pointer points to qTD1, transfer overlay region still have reference to qTD2. But qtD2 is just unlinked and freed. This may cause EHCI system error. Fix this by updating qTD next pointer in QH overlay region with the qTD next pointer of the current qTD. Signed-off-by: Pavankumar Kondeti Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

USB: ftdi_sio: do not claim CDC ACM function

2012-09-19T14:05:19Z

commit f08dea734844aa42ec57c229b0b73b3d7d21f810 upstream. The Microchip vid:pid 04d8:000a is used for their CDC ACM demo firmware application. This is a device with a single function conforming to the CDC ACM specification and with the intention of demonstrating CDC ACM class firmware and driver interaction. The demo is used on a number of development boards, and may also be used unmodified by vendors using Microchip hardware. Some vendors have re-used this vid:pid for other types of firmware, emulating FTDI chips. Attempting to continue to support such devices without breaking class based applications that by matching on interface class/subclass/proto being ff/ff/00. I have no information about the actual device or interface descriptors, but this will at least make the proper CDC ACM devices work again. Anyone having details of the offending device's descriptors should update this entry with the details. Reported-by: Florian Wöhrl Reported-by: Xiaofan Chen Cc: Alan Cox Cc: Bruno Thomsen Signed-off-by: Bjørn Mork Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

USB: add device quirk for Joss Optical touchboard

2012-09-19T14:05:16Z

commit 92fc7a8b0f20bdb243c706daf42658e8e0cd2ef0 upstream. This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss infrared touchboard device. The device doesn't like to be asked for its interface strings. Signed-off-by: Alan Stern Reported-by: adam ? Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

USB: ftdi_sio: PID for NZR SEM 16+ USB

2012-09-19T14:05:15Z

commit 26a538b9ea2a3ee10dafc0068f0560dfd7b7ba37 upstream. This adds the USB PID for the NZR SEM 16+ USB energy monitor device . It works perfectly with the GPL software on . Signed-off-by: Horst Schirmeier Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

USB: ftdi-sio: add support for more Physik Instrumente devices

2012-09-19T14:05:15Z

commit dafc4f7be1a556ca3868d343c00127728b397068 upstream. Commit b69cc672052540 added support for the E-861. After acquiring a C-867, I realised that every Physik Instrumente's device has a different PID. They are listed in the Windows device driver's .inf file. So here are all PIDs for the current (and probably future) USB devices from Physik Instrumente. Compiled, but only actually tested on the E-861 and C-867. Signed-off-by: Éric Piel Signed-off-by: Greg Kroah-Hartman Signed-off-by: Ben Hutchings

usb: host: xhci: fix compilation error for non-PCI based stacks

2012-09-19T14:05:13Z

commit 296365781903226a3fb8758901eaeec09d2798e4 upstream. For non PCI-based stacks, this function call usb_disable_xhci_ports(to_pci_dev(hcd->self.controller)); made from xhci_shutdown is not applicable. Ideally, we wouldn't have any PCI-specific code on a generic driver such as the xHCI stack, but it looks like we should just stub usb_disable_xhci_ports() out for non-PCI devices. [ balbi@ti.com: slight improvement to commit log ] This patch should be backported to kernels as old as 3.0, since the commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch PPT ports to EHCI on shutdown.") was marked for stable. Signed-off-by: Moiz Sonasath Signed-off-by: Ruchika Kharwar Signed-off-by: Felipe Balbi Signed-off-by: Sarah Sharp Signed-off-by: Ben Hutchings

usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware

2012-09-19T14:05:13Z

commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 upstream. This patch is intended to work around a known issue on the SN65LVPE502CP USB3.0 re-driver that can delay the negotiation between a device and the host past the usual handshake timeout. If that happens on the first insertion, the host controller port will enter in Compliance Mode and NO port status event will be generated (as per xHCI Spec) making impossible to detect this event by software. The port will remain in compliance mode until a warm reset is applied to it. As a result of this, the port will seem "dead" to the user and no device connections or disconnections will be detected. For solving this, the patch creates a timer which polls every 2 seconds the link state of each host controller's port (this by reading the PORTSC register) and recovers the port by issuing a Warm reset every time Compliance mode is detected. If a xHC USB3.0 port has previously entered to U0, the compliance mode issue will NOT occur only until system resumes from sleep/hibernate, therefore, the compliance mode timer is stopped when all xHC USB 3.0 ports have entered U0. The timer is initialized again after each system resume. Since the issue is being caused by a piece of hardware, the timer will be enabled ONLY on those systems that have the SN65LVPE502CP installed (this patch uses DMI strings for detecting those systems) therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK has been added to the xhci stack). This patch applies for these systems: Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820. This patch should be backported to kernels as old as 3.2, as that was the first kernel to support warm reset. The kernels will need to contain both commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When hot reset for USB3 fails, try warm reset" and commit 8bea2bd37df08aaa599aa361a9f8b836ba98e554 "usb: Add support for root hub port status CAS". The first patch add warm reset support, and the second patch modifies the USB core to issue a warm reset when the port is in compliance mode. Signed-off-by: Alexis R. Cortes Signed-off-by: Sarah Sharp [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

xhci: Make handover code more robust

2012-09-19T14:05:12Z

commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream. My test platform (Intel DX79SI) boots reliably under BIOS, but frequently crashes when booting via UEFI. I finally tracked this down to the xhci handoff code. It seems that reads from the device occasionally just return 0xff, resulting in xhci_find_next_cap_offset generating a value that's larger than the resource region. We then oops when attempting to read the value. Sanity checking that value lets us avoid the crash. I've no idea what's causing the underlying problem, and xhci still doesn't actually *work* even with this, but the machine at least boots which will probably make further debugging easier. This should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff and HW initialization." Signed-off-by: Matthew Garrett Signed-off-by: Sarah Sharp Signed-off-by: Ben Hutchings