user/sven/linux.git/drivers, branch v3.2.73

asix: Do full reset during ax88772_bind

2015-11-17T15:54:46Z

[ Upstream commit 436c2a5036b6ffe813310df2cf327d3b69be0734 ] commit 3cc81d85ee01 ("asix: Don't reset PHY on if_up for ASIX 88772") causes the ethernet on Arndale to no longer function. This appears to be because the Arndale ethernet requires a full reset before it will function correctly, however simply reverting the above patch causes problems with ethtool settings getting reset. It seems the problem is that the ethernet is not properly reset during bind, and indeed the code in ax88772_bind that resets the device is a very small subset of the actual ax88772_reset function. This patch uses ax88772_reset in place of the existing reset code in ax88772_bind which removes some code duplication and fixes the ethernet on Arndale. It is still possible that the original patch causes some issues with suspend and resume but that seems like a separate issue and I haven't had a chance to test that yet. Signed-off-by: Charles Keepax Tested-by: Riku Voipio Signed-off-by: David S. Miller [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings

asix: Don't reset PHY on if_up for ASIX 88772

2015-11-17T15:54:46Z

[ Upstream commit 3cc81d85ee01e5a0b7ea2f4190e2ed1165f53c31 ] I've noticed every time the interface is set to 'up,', the kernel reports that the link speed is set to 100 Mbps/Full Duplex, even when ethtool is used to set autonegotiation to 'off', half duplex, 10 Mbps. It can be tested by: ifconfig eth0 down ethtool -s eth0 autoneg off speed 10 duplex half ifconfig eth0 up Then checking 'dmesg' for the link speed. Signed-off-by: Michel Stam Signed-off-by: David S. Miller [bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings

mvsas: Fix NULL pointer dereference in mvs_slot_task_free

2015-11-17T15:54:45Z

commit 2280521719e81919283b82902ac24058f87dfc1b upstream. When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays NULL but it's later used in mvs_abort_task as slot which is passed to mvs_slot_task_free causing NULL pointer dereference. Just return from mvs_slot_task_free when passed with NULL slot. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891 Signed-off-by: Dāvis Mosāns Reviewed-by: Tomas Henzl Reviewed-by: Johannes Thumshirn Signed-off-by: James Bottomley Signed-off-by: Ben Hutchings

md/raid10: don't clear bitmap bit when bad-block-list write fails.

2015-11-17T15:54:45Z

commit c340702ca26a628832fade4f133d8160a55c29cc upstream. When a write fails and a bad-block-list is present, we can update the bad-block-list instead of writing the data. If this succeeds then it is OK clear the relevant bitmap-bit as no further 'sync' of the block is needed. However if writing the bad-block-list fails then we need to treat the write as failed and particularly must not clear the bitmap bit. Otherwise the device can be re-added (after any hardware connection issues are resolved) and because the relevant bit in the bitmap is clear, that block will not be resynced. This leads to data corruption. We already delay the final bio_endio() on the write until the bad-block-list is written so that when the write returns: either that data is safe, the bad-block record is safe, or the fact that the device is faulty is safe. However we *don't* delay the clearing of the bitmap, so the bitmap bit can be recorded as cleared before we know if the bad-block-list was written safely. So: delay that until the write really is safe. i.e. move the call to close_write() until just before calling bio_endio(), and recheck the 'is array degraded' status before making that call. This bug goes back to v3.1 when bad-block-lists were introduced, though it only affects arrays created with mdadm-3.3 or later as only those have bad-block lists. Backports will require at least Commit: 95af587e95aa ("md/raid10: ensure device failure recorded before write request returns.") as well. I'll send that to 'stable' separately. Note that of the two tests of R10BIO_WriteError that this patch adds, the first is certain to fail and the second is certain to succeed. However doing it this way makes the patch more obviously correct. I will tidy the code up in a future merge window. Reported-by: Nate Dailey Fixes: bd870a16c594 ("md/raid10: Handle write errors by updating badblock log.") Signed-off-by: NeilBrown Signed-off-by: Ben Hutchings

md/raid10: ensure device failure recorded before write request returns.

2015-11-17T15:54:45Z

commit 95af587e95aacb9cfda4a9641069a5244a540dc8 upstream. When a write to one of the legs of a RAID10 fails, the failure is recorded in the metadata of the other legs so that after a restart the data on the failed drive wont be trusted even if that drive seems to be working again (maybe a cable was unplugged). Currently there is no interlock between the write request completing and the metadata update. So it is possible that the write will complete, the app will confirm success in some way, and then the machine will crash before the metadata update completes. This is an extremely small hole for a racy to fit in, but it is theoretically possible and so should be closed. So: - set MD_CHANGE_PENDING when requesting a metadata update for a failed device, so we can know with certainty when it completes - queue requests that experienced an error on a new queue which is only processed after the metadata update completes - call raid_end_bio_io() on bios in that queue when the time comes. Signed-off-by: NeilBrown [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

md/raid1: don't clear bitmap bit when bad-block-list write fails.

2015-11-17T15:54:45Z

commit bd8688a199b864944bf62eebed0ca13b46249453 upstream. When a write fails and a bad-block-list is present, we can update the bad-block-list instead of writing the data. If this succeeds then it is OK clear the relevant bitmap-bit as no further 'sync' of the block is needed. However if writing the bad-block-list fails then we need to treat the write as failed and particularly must not clear the bitmap bit. Otherwise the device can be re-added (after any hardware connection issues are resolved) and because the relevant bit in the bitmap is clear, that block will not be resynced. This leads to data corruption. We already delay the final bio_endio() on the write until the bad-block-list is written so that when the write returns: either that data is safe, the bad-block record is safe, or the fact that the device is faulty is safe. However we *don't* delay the clearing of the bitmap, so the bitmap bit can be recorded as cleared before we know if the bad-block-list was written safely. So: delay that until the write really is safe. i.e. move the call to close_write() until just before calling bio_endio(), and recheck the 'is array degraded' status before making that call. This bug goes back to v3.1 when bad-block-lists were introduced, though it only affects arrays created with mdadm-3.3 or later as only those have bad-block lists. Backports will require at least Commit: 55ce74d4bfe1 ("md/raid1: ensure device failure recorded before write request returns.") as well. I'll send that to 'stable' separately. Note that of the two tests of R1BIO_WriteError that this patch adds, the first is certain to fail and the second is certain to succeed. However doing it this way makes the patch more obviously correct. I will tidy the code up in a future merge window. Reported-and-tested-by: Nate Dailey Cc: Jes Sorensen Fixes: cd5ff9a16f08 ("md/raid1: Handle write errors by updating badblock log.") Signed-off-by: NeilBrown Signed-off-by: Ben Hutchings

md/raid1: ensure device failure recorded before write request returns.

2015-11-17T15:54:45Z

commit 55ce74d4bfe1b9444436264c637f39a152d1e5ac upstream. When a write to one of the legs of a RAID1 fails, the failure is recorded in the metadata of the other leg(s) so that after a restart the data on the failed drive wont be trusted even if that drive seems to be working again (maybe a cable was unplugged). Similarly when we record a bad-block in response to a write failure, we must not let the write complete until the bad-block update is safe. Currently there is no interlock between the write request completing and the metadata update. So it is possible that the write will complete, the app will confirm success in some way, and then the machine will crash before the metadata update completes. This is an extremely small hole for a racy to fit in, but it is theoretically possible and so should be closed. So: - set MD_CHANGE_PENDING when requesting a metadata update for a failed device, so we can know with certainty when it completes - queue requests that experienced an error on a new queue which is only processed after the metadata update completes - call raid_end_bio_io() on bios in that queue when the time comes. Signed-off-by: NeilBrown [bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings

dm btree: fix leak of bufio-backed block in btree_split_beneath error path

2015-11-17T15:54:45Z

commit 4dcb8b57df3593dcb20481d9d6cf79d1dc1534be upstream. btree_split_beneath()'s error path had an outstanding FIXME that speaks directly to the potential for _not_ cleaning up a previously allocated bufio-backed block. Fix this by releasing the previously allocated bufio block using unlock_block(). Reported-by: Mikulas Patocka Signed-off-by: Mike Snitzer Acked-by: Joe Thornber Signed-off-by: Ben Hutchings

dm btree remove: fix a bug when rebalancing nodes after removal

2015-11-17T15:54:45Z

commit 2871c69e025e8bc507651d5a9cf81a8a7da9d24b upstream. Commit 4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't a complete fix for redistribute3(). The redistribute3 function takes 3 btree nodes and shares out the entries evenly between them. If the three nodes in total contained (MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in the center. Fix this issue by being more careful about calculating the target number of entries for the left and right nodes. Unit tested in userspace using this program: https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c Signed-off-by: Joe Thornber Signed-off-by: Mike Snitzer Signed-off-by: Ben Hutchings

ppp: fix pppoe_dev deletion condition in pppoe_release()

2015-11-17T15:54:44Z

commit 1acea4f6ce1b1c0941438aca75dd2e5c6b09db60 upstream. We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev. PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies (po->pppoe_dev != NULL). Since we're releasing a PPPoE socket, we want to release the pppoe_dev if it exists and reset sk_state to PPPOX_DEAD, no matter the previous value of sk_state. So we can just check for po->pppoe_dev and avoid any assumption on sk->sk_state. Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Signed-off-by: Guillaume Nault Signed-off-by: David S. Miller Signed-off-by: Ben Hutchings