user/sven/linux.git/drivers, branch v4.19.207

net: renesas: sh_eth: Fix freeing wrong tx descriptor

2021-09-22T09:48:14Z

[ Upstream commit 0341d5e3d1ee2a36dd5a49b5bef2ce4ad1cfa6b4 ] The cur_tx counter must be incremented after TACT bit of txdesc->status was set. However, a CPU is possible to reorder instructions and/or memory accesses between cur_tx and txdesc->status. And then, if TX interrupt happened at such a timing, the sh_eth_tx_free() may free the descriptor wrongly. So, add wmb() before cur_tx++. Otherwise NETDEV WATCHDOG timeout is possible to happen. Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet") Signed-off-by: Yoshihiro Shimoda Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

qlcnic: Remove redundant unlock in qlcnic_pinit_from_rom

2021-09-22T09:48:14Z

[ Upstream commit 9ddbc2a00d7f63fa9748f4278643193dac985f2d ] Previous commit 68233c583ab4 removes the qlcnic_rom_lock() in qlcnic_pinit_from_rom(), but remains its corresponding unlock function, which is odd. I'm not very sure whether the lock is missing, or the unlock is redundant. This bug is suggested by a static analysis tool, please advise. Fixes: 68233c583ab4 ("qlcnic: updated reset sequence") Signed-off-by: Dinghao Liu Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: b53: Fix calculating number of switch ports

2021-09-22T09:48:14Z

[ Upstream commit cdb067d31c0fe4cce98b9d15f1f2ef525acaa094 ] It isn't true that CPU port is always the last one. Switches BCM5301x have 9 ports (port 6 being inactive) and they use port 5 as CPU by default (depending on design some other may be CPU ports too). A more reliable way of determining number of ports is to check for the last set bit in the "enabled_ports" bitfield. This fixes b53 internal state, it will allow providing accurate info to the DSA and is required to fix BCM5301x support. Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Rafał Miłecki Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'

2021-09-22T09:48:13Z

[ Upstream commit 6b430c7595e4eb95fae8fb54adc3c3ce002e75ae ] A successful 'init_rs_non_canonical()' call should be balanced by a corresponding 'free_rs()' call in the error handling path of the probe, as already done in the remove function. Update the error handling path accordingly. Fixes: 8c61b7a7f4d4 ("[MTD] [NAND] Use rslib for CAFÉ ECC") Signed-off-by: Christophe JAILLET Signed-off-by: Miquel Raynal Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin

PCI: Fix pci_dev_str_match_path() alloc while atomic bug

2021-09-22T09:48:13Z

[ Upstream commit 7eb6ea4148579b85540a41d57bcec315b8af8ff8 ] pci_dev_str_match_path() is often called with a spinlock held so the allocation has to be atomic. The call tree is: pci_specified_resource_alignment() <-- takes spin_lock(); pci_dev_str_match() pci_dev_str_match_path() Fixes: 45db33709ccc ("PCI: Allow specifying devices using a base bus and path of devfns") Link: https://lore.kernel.org/r/20210812070004.GC31863@kili Signed-off-by: Dan Carpenter Signed-off-by: Bjorn Helgaas Reviewed-by: Logan Gunthorpe Signed-off-by: Sasha Levin

mfd: axp20x: Update AXP288 volatile ranges

2021-09-22T09:48:13Z

[ Upstream commit f949a9ebce7a18005266b859a17f10c891bb13d7 ] On Cherry Trail devices with an AXP288 PMIC the external SD-card slot used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO (GPIO1 pin in low noise LDO mode) as signal-voltage. These regulators are turned on/off and in case of the signal-voltage also have their output-voltage changed by the _PS0 and _PS3 power- management ACPI methods on the MMC-controllers ACPI fwnode as well as by the _DSM ACPI method for changing the signal voltage. The AML code implementing these methods is directly accessing the PMIC through ACPI I2C OpRegion accesses, instead of using the special PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c . This means that the contents of the involved PMIC registers can change without the change being made through the regmap interface, so regmap should not cache the contents of these registers. Mark the regulator power on/off, the regulator voltage control and the GPIO1 control registers as volatile, to avoid regmap caching them. Specifically this fixes an issue on some models where the i915 driver toggles another LDO using the same on/off register on/off through MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element()) which then writes back a cached on/off register-value where the card-voltage is off causing the external sdcard slot to stop working when the screen goes blank, or comes back on again. The regulator register-range now marked volatile also includes the buck regulator control registers. This is done on purpose these are normally not touched by the AML code, but they are updated directly by the SoC's PUNIT which means that they may also change without going through regmap. Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms, so even though this is an ACPI specific problem there is no need to make the new volatile ranges conditional since these platforms always use ACPI. Fixes: dc91c3b6fe66 ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile") Fixes: cd53216625a0 ("mfd: axp20x: Fix axp288 volatile ranges") Reported-and-tested-by: Clamshell Signed-off-by: Hans de Goede Reviewed-by: Chen-Yu Tsai Signed-off-by: Lee Jones Signed-off-by: Sasha Levin

NTB: perf: Fix an error code in perf_setup_inbuf()

2021-09-22T09:48:13Z

[ Upstream commit 0097ae5f7af5684f961a5f803ff7ad3e6f933668 ] When the function IS_ALIGNED() returns false, the value of ret is 0. So, we set ret to -EINVAL to indicate this error. Clean up smatch warning: drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error code 'ret'. Reported-by: Abaci Robot Signed-off-by: Yang Li Reviewed-by: Serge Semin Signed-off-by: Jon Mason Signed-off-by: Sasha Levin

ethtool: Fix an error code in cxgb2.c

2021-09-22T09:48:13Z

[ Upstream commit 7db8263a12155c7ae4ad97e850f1e499c73765fc ] When adapter->registered_device_map is NULL, the value of err is uncertain, we set err to -EINVAL to avoid ambiguity. Clean up smatch warning: drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing error code 'err' Reported-by: Abaci Robot Signed-off-by: Yang Li Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: usb: cdc_mbim: avoid altsetting toggling for Telit LN920

2021-09-22T09:48:13Z

[ Upstream commit aabbdc67f3485b5db27ab4eba01e5fbf1ffea62c ] Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920 0x1061 composition in order to avoid bind error. Signed-off-by: Daniele Palmas Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

PCI: Add ACS quirks for Cavium multi-function devices

2021-09-22T09:48:12Z

[ Upstream commit 32837d8a8f63eb95dcb9cd005524a27f06478832 ] Some Cavium endpoints are implemented as multi-function devices without ACS capability, but they actually don't support peer-to-peer transactions. Add ACS quirks to declare DMA isolation for the following devices: - BGX device found on Octeon-TX (8xxx) - CGX device found on Octeon-TX2 (9xxx) - RPM device found on Octeon-TX3 (10xxx) Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com Signed-off-by: George Cherian Signed-off-by: Bjorn Helgaas Signed-off-by: Sasha Levin