user/sven/linux.git/include/linux/ethtool.h, branch v5.16.4

ethtool: Add transceiver module extended state

2021-10-07T00:47:50Z

Add an extended state and sub-state to describe link issues related to transceiver modules. The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state tells user space that port is unable to gain a carrier because the CMIS Module State Machine did not reach the ModuleReady (Fully Operational) state. For example, if the module is stuck at ModuleLowPwr or ModuleFault state. In case of the latter, user space can read the fault reason from the module's EEPROM and potentially reset it. Signed-off-by: Ido Schimmel Signed-off-by: Jakub Kicinski

ethtool: Add ability to control transceiver modules' power mode

2021-10-07T00:47:49Z

Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver modules parameters and retrieve their status. The first parameter to control is the power mode of the module. It is only relevant for paged memory modules, as flat memory modules always operate in low power mode. When a paged memory module is in low power mode, its power consumption is reduced to the minimum, the management interface towards the host is available and the data path is deactivated. User space can choose to put modules that are not currently in use in low power mode and transition them to high power mode before putting the associated ports administratively up. This is useful for user space that favors reduced power consumption and lower temperatures over reduced link up times. In QSFP-DD modules the transition from low power mode to high power mode can take a few seconds and this transition is only expected to get longer with future / more complex modules. User space can control the power mode of the module via the power mode policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible values: * high: Module is always in high power mode. * auto: Module is transitioned by the host to high power mode when the first port using it is put administratively up and to low power mode when the last port using it is put administratively down. The operational power mode of the module is available to user space via the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not reported to user space when a module is not plugged-in. The user API is designed to be generic enough so that it could be used for modules with different memory maps (e.g., SFF-8636, CMIS). The only implementation of the device driver API in this series is for a MAC driver (mlxsw) where the module is controlled by the device's firmware, but it is designed to be generic enough so that it could also be used by implementations where the module is controlled by the CPU. CMIS testing ============ # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off The module is not in low power mode, as it is not forced by hardware (LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off). The power mode can be queried from the kernel. In case LowPwrAllowRequestHW was on, the kernel would need to take into account the state of the LowPwrRequestHW signal, which is not visible to user space. $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp11 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp11 up Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp11 down Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On SFF-8636 testing ================ # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm The module is not in low power mode, as it is not forced by hardware (Power override is on) or by software (Power set is off). The power mode can be queried from the kernel. In case Power override was off, the kernel would need to take into account the state of the LPMode signal, which is not visible to user space. $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp13 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp13 up Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp13 down Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Signed-off-by: Ido Schimmel Signed-off-by: Jakub Kicinski

ethtool: extend coalesce setting uAPI with CQE mode

2021-08-24T14:38:29Z

In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo Signed-off-by: Huazhong Tan Signed-off-by: Jakub Kicinski

ethtool: add two coalesce attributes for CQE mode

2021-08-24T14:38:28Z

Currently, there are many drivers who support CQE mode configuration, some configure it as a fixed when initialized, some provide an interface to change it by ethtool private flags. In order to make it more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and 'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these parameters can be accessed by ethtool netlink coalesce uAPI. Also add an new structure kernel_ethtool_coalesce, then the new parameter can be added into this struct. Signed-off-by: Yufeng Mo Signed-off-by: Huazhong Tan Signed-off-by: Jakub Kicinski

ethtool: improve compat ioctl handling

2021-07-23T13:20:25Z

The ethtool compat ioctl handling is hidden away in net/socket.c, which introduces a couple of minor oddities: - The implementation may end up diverging, as seen in the RXNFC extension in commit 84a1d9c48200 ("net: ethtool: extend RXNFC API to support RSS spreading of filter matches") that does not work in compat mode. - Most architectures do not need the compat handling at all because u64 and compat_u64 have the same alignment. - On x86, the conversion is done for both x32 and i386 user space, but it's actually wrong to do it for x32 and cannot work there. - On 32-bit Arm, it never worked for compat oabi user space, since that needs to do the same conversion but does not. - It would be nice to get rid of both compat_alloc_user_space() and copy_in_user() throughout the kernel. None of these actually seems to be a serious problem that real users are likely to encounter, but fixing all of them actually leads to code that is both shorter and more readable. Signed-off-by: Arnd Bergmann Reviewed-by: Christoph Hellwig Signed-off-by: David S. Miller

ethtool: add a new command for getting PHC virtual clocks

2021-07-01T20:08:18Z

Add an interface for getting PHC (PTP Hardware Clock) virtual clocks, which are based on PHC physical clock providing hardware timestamp to network packets. Signed-off-by: Yangbo Lu Signed-off-by: David S. Miller

ethtool: Use kernel data types for internal EEPROM struct

2021-06-22T17:40:54Z

The struct is not visible to user space and therefore should not use the user visible data types. Instead, use internal data types like other structures in the file. Signed-off-by: Ido Schimmel Signed-off-by: David S. Miller

ethtool: add interface to read RMON stats

2021-04-16T23:59:20Z

Most devices maintain RMON (RFC 2819) stats - particularly the "histogram" of packets received by size. Unlike other RFCs which duplicate IEEE stats, the short/oversized frame counters in RMON don't seem to match IEEE stats 1-to-1 either, so expose those, too. Do not expose basic packet, CRC errors etc - those are already otherwise covered. Because standard defines packet ranges only up to 1518, and everything above that should theoretically be "oversized" - devices often create their own ranges. Going beyond what the RFC defines - expose the "histogram" in the Tx direction (assume for now that the ranges will be the same). Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller

ethtool: add interface to read standard MAC Ctrl stats

2021-04-16T23:59:20Z

Number of devices maintains the standard-based MAC control counters for control frames. Add a API for those. Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller

ethtool: add interface to read standard MAC stats

2021-04-16T23:59:20Z

Most of the MAC statistics are included in struct rtnl_link_stats64, but some fields are aggregated. Besides it's good to expose these clearly hardware stats separately. Signed-off-by: Jakub Kicinski Signed-off-by: David S. Miller