user/sven/linux.git/include/linux/iio/common, branch v4.19.53

iio: cros_ec: Move cros_ec_sensors_core.h in /include

2018-03-17T19:59:20Z

Similar to other common iio frameworks, move cros_ec_sensors_core.h from drivers/iio/common/cros_ec_sensors/ to include/linux/iio/common. Signed-off-by: Gwendal Grignou Signed-off-by: Jonathan Cameron

iio: st_sensors: split open-drain parameters for irq1 and irq2

2017-10-10T19:38:39Z

Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order to contain irq line parameters of the device. Moreover separate data-ready open-drain configuration parameters for INT1 and INT2 pins in st_sensor_data_ready_irq data structure. That change will be used to properly support LIS3DHH accel sensor. Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron

iio: st_sensors: decouple irq1 configuration parameters from the irq2 ones

2017-10-09T20:04:22Z

Separate data-ready configuration parameters for INT1 and INT2 pins in st_sensor_data_ready_irq data structure. That change will be use to properly support LIS2DW12 accel sensor. Signed-off-by: Lorenzo Bianconi Reviewed-by: Linus Walleij Signed-off-by: Jonathan Cameron

iio: st_sensors: add register mask for status register

2017-10-09T20:01:45Z

Introduce register mask for data-ready status register since pressure sensors (e.g. LPS22HB) export just two channels (BIT(0) and BIT(1)) and BIT(2) is marked reserved while in st_sensors_new_samples_available() value read from status register is masked using 0x7. Moreover do not mask status register using active_scan_mask since now status value is properly masked and if the result is not zero the interrupt has to be consumed by the driver. This fix an issue on LPS25H and LPS331AP where channel definition is swapped respect to status register. Furthermore that change allows to properly support new devices (e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register to figure out if the interrupt has been generated by the device. Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi Reviewed-by: Linus Walleij Signed-off-by: Jonathan Cameron

Merge 4.13-rc5 into staging-next

2017-08-14T20:35:22Z

We need it here for iio fixes. Signed-off-by: Greg Kroah-Hartman

iio: accel: st_accel: add SPI-3wire support

2017-07-06T18:32:29Z

Add SPI Serial Interface Mode (SIM) register information in st_sensor_settings look up table to support devices (like LSM303AGR accel sensor) that allow just SPI-3wire communication mode. SIM mode has to be configured before any other operation since it is not enabled by default and the driver is not able to read without that configuration Whilst a fairly substantial patch, the actual logic is simple and it is better to have the generic fix than a band aid. Fixes: ddc05fa28606 (iio: st-accel: add support for lsm303agr accel) Signed-off-by: Lorenzo Bianconi Cc: Signed-off-by: Jonathan Cameron

iio: common: st_sensors: move st_sensors_of_i2c_probe() in common code

2017-07-01T09:16:56Z

Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in st_sensors_of_name_probe(). That change is necessary to add device-tree support in spi code otherwise the rest of the autodetection will fail since spi->modalias (and indio_dev->name) will be set using compatible string value that differs from standard sensor name Signed-off-by: Lorenzo Bianconi Signed-off-by: Jonathan Cameron

Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

2017-01-19T09:40:44Z

Jonathan writes: First round of new device support, features and cleanups for IIO in the 4.11 cycle. It's shaping to be another fairly busy cycle. Lots more on the way! New device support * ads7950 - new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954, ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs. * cm3605 - New driver for this light sensor and proximity sensor which is an analog part with some additional digital controls. * hx711 - New driver. Core new stuff * Gravity sensor type. This is a processed datastream in which the device will try to work out which way is down. * Split the buffer.h file into two parts. One provides the interface to 'use' a buffer, the second provides the internals of the buffer functionality as needed by implementations of buffers. - Move documentation inline so as to allow use of private: tag when generating documentation. - Add some utility functions for the few things that are directly done with the buffers. - Stop exporting functions that no-one uses outside of the core code. - Push docs down by the code in the c file where they should have always been. - Fix typo in kernel-doc for buffer. - push down some includes that were previously happening implicitly. - stop enabling the timestamp of the dummy device. Features and cleanups * ad5592r - ACPI support * ad5593r -ACPI support. * ad5933 - Fix a false comment about size of a particular register. * ad7150 - replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches in general, but as it was nicely presented I took this one anyway. As a general rule will only take these as part of a larger driver cleanup. - don't eat an error but rather reutnr it in the write_event_config callback. * ad7606 - replace non standard range attibute with _scale * ade7753 - use usleep_range for short sleeps * ade7754 - use usleep_range for short sleeps * ade7758 - use usleep_range for short sleeps * ade7759 - use usleep_range for short sleeps * ade7854 - use usleep_range for short sleeps * adis16201 - fix description * adis16203 - fix description - fix copyright year * adis16209 - fix description * adt7316 - Add braces to arms of if else statement (for consistency) - Alignment fixes. * axp288 - Fix up an issue with accidental overwrites of data. * bmi160 - add deivce tables for i2c and spi to support correctly identifying the full dt name (including manufacturer). - device tree binding. * bmp280 - use usleep_range for short sleeps. * cm3232 - return error from cm3232_reg_init rather than eating it if the last write fails. * dummy driver - remove a semicolor found at end of a function defintition. * exynos-adc - use usleep_range for short sleeps. * hid-sensor (accel) - Add timestamp support. The hardware can provide timestamps so lets support them. If not fall back to timestamps estimated in kernel. * hid-sensor (light) - Add a duplicate ID for the light channels so as to keep existing interface whilst also using the more standard IIO interface. * hts221 - acpi probing * imx25-gcq - Add a macro call to allow this driver to be automatically loaded. * isl29028 - reorganise code to avoid deep nesting of if statements. - move chip test and default regs into a function suitable or sharing with power management code. - tidy up some code alignment. * lidar-lite-v3 - introduce compatible strings that make it clear Garmin have consideral friends. * mma8452 - avoid returning signed value when unsigned is appropriate * spmi-vadc - Update function for generic voltage conversion to take into account that different channels on this device should be handled differently. - Rework code to allow per channel voltage scaling and support the standard options for this hardware. - Fixup three minor issues with the above patches for this part. These all effect test builds rather than the native builds for the part, but good to clean them up anyway. * st_sensors - support device matching from the ACPI DST tables. - acpi based probing for accelerometers - acpi based probing for pressure sensors - Allow pressure sensors to read negative values. - Export sampling frequency for lps25h and lps331ap. - Add support for the old DT bindings from the period when these deivces were often supported through windows. Docs fixup: * typo in sysfs-bus-iio

iio: accel: st_accel: fix LIS3LV02 reading and scaling

2016-12-31T14:35:04Z

The LIS3LV02 has a special bit that need to be set to get the read values left aligned. Before this patch we get gibberish like this: iio_generic_buffer -a -c10 -n lis3lv02dl_accel (...) 0.000000 -0.010042 -0.642688 19155832931907 0.000000 -0.010042 -0.642688 19155858751073 Which is because we read a raw value for 1g as 64 which is the nominal 1024 for 1g shifted 4 bits to the left by being right-aligned rather than left aligned. Since all other sensors are left aligned, add some code to set the special DAS (data alignment setting) bit to 1 so that the right value is now read like this: iio_generic_buffer -a -c10 -n lis3lv02dl_accel (...) 0.000000 -0.147095 -10.120135 24761614364956 -0.029419 -0.176514 -10.120135 24761631624540 The scaling was weird as well: we have a gain of 1000 for 1g and 3000 for 6g. I don't even remember how I came up with the old values but they are wrong. Fixes: 3acddf74f807 ("iio: st-sensors: add support for lis3lv02d accelerometer") Cc: Lorenzo Bianconi Cc: Giuseppe Barba Cc: Denis Ciocca Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron

iio: st_sensors: match sensors using ACPI handle

2016-12-03T08:56:26Z

Add support to match st sensors using information passed from ACPI DST tables. Signed-off-by: Shrirang Bagul Signed-off-by: Jonathan Cameron