user/sven/linux.git/include/linux/iio, branch v4.14.235

iio: ad_sigma_delta: Properly handle SPI bus locking vs CS assertion

2019-05-31T13:47:29Z

[ Upstream commit df1d80aee963480c5c2938c64ec0ac3e4a0df2e0 ] For devices from the SigmaDelta family we need to keep CS low when doing a conversion, since the device will use the MISO line as a interrupt to indicate that the conversion is complete. This is why the driver locks the SPI bus and when the SPI bus is locked keeps as long as a conversion is going on. The current implementation gets one small detail wrong though. CS is only de-asserted after the SPI bus is unlocked. This means it is possible for a different SPI device on the same bus to send a message which would be wrongfully be addressed to the SigmaDelta device as well. Make sure that the last SPI transfer that is done while holding the SPI bus lock de-asserts the CS signal. Signed-off-by: Lars-Peter Clausen Signed-off-by: Alexandru Ardelean Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin

iio: buffer: fix the function signature to match implementation

2018-11-04T13:52:45Z

[ Upstream commit 92397a6c38d139d50fabbe9e2dc09b61d53b2377 ] linux/iio/buffer-dma.h was not updated to when length was changed to unsigned int. Fixes: c043ec1ca5ba ("iio:buffer: make length types match kfifo types") Signed-off-by: Phil Reid Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin

iio:buffer: make length types match kfifo types

2018-06-05T09:41:58Z

commit c043ec1ca5baae63726aae32abbe003192bc6eec upstream. Currently, we use int for buffer length and bytes_per_datum. However, kfifo uses unsigned int for length and size_t for element size. We need to make sure these matches or we will have bugs related to overflow (in the range between INT_MAX and UINT_MAX for length, for example). In addition, set_bytes_per_datum uses size_t while bytes_per_datum is an int, which would cause bugs for large values of bytes_per_datum. Change buffer length to use unsigned int and bytes_per_datum to use size_t. Signed-off-by: Martin Kelly Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: st_sensors: add register mask for status register

2017-12-25T13:26:26Z

[ Upstream commit e72a060151e5bb673af24993665e270fc4f674a7 ] Introduce register mask for data-ready status register since pressure sensors (e.g. LPS22HB) export just two channels (BIT(0) and BIT(1)) and BIT(2) is marked reserved while in st_sensors_new_samples_available() value read from status register is masked using 0x7. Moreover do not mask status register using active_scan_mask since now status value is properly masked and if the result is not zero the interrupt has to be consumed by the driver. This fix an issue on LPS25H and LPS331AP where channel definition is swapped respect to status register. Furthermore that change allows to properly support new devices (e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register to figure out if the interrupt has been generated by the device. Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi Reviewed-by: Linus Walleij Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

iio: stm32: fix adc/trigger link error

2017-12-14T08:52:48Z

commit 6d745ee8b5e81f3a33791e3c854fbbfd6f3e585e upstream. The ADC driver can trigger on either the timer or the lptim trigger, but it only uses a Kconfig 'select' statement to ensure that the first of the two is present. When the lptim trigger is enabled as a loadable module, and the adc driver is built-in, we now get a link error: drivers/iio/adc/stm32-adc.o: In function `stm32_adc_get_trig_extsel': stm32-adc.c:(.text+0x4e0): undefined reference to `is_stm32_lptim_trigger' We could use a second 'select' statement and always have both trigger drivers enabled when the adc driver is, but it seems that the lptimer trigger was intentionally left optional, so it seems better to keep it that way. This adds a hack to use 'IS_REACHABLE()' rather than 'IS_ENABLED()', which avoids the link error, but instead leads to the lptimer trigger not being used in the broken configuration. I've added a runtime warning for this case to help users figure out what they did wrong if this should ever be done by accident. Fixes: f0b638a7f6db ("iio: adc: stm32: add support for lptimer triggers") Signed-off-by: Arnd Bergmann Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

2017-09-25T08:58:22Z

Jonathan writes: First round of IIO fixes for the 4.14 cycle Note this includes fixes from recent merge window. As such the tree is based on top of a prior staging/staging-next tree. * iio core - return and error for a failed read_reg debugfs call rather than eating the error. * ad7192 - Use the dedicated reset function in the ad_sigma_delta library instead of an spi transfer with the data on the stack which could cause problems with DMA. * ad7793 - Implement a dedicate reset function in the ad_sigma_delta library and use it to correctly reset this part. * bme280 - ctrl_reg write must occur after any register writes for updates to take effect. * mcp320x - negative voltage readout was broken. - Fix an oops on module unload due to spi_set_drvdata not being called in probe. * st_magn - Fix the data ready line configuration for the lis3mdl. It is not configurable so the st_magn core was assuming it didn't exist and so wasn't consuming interrupts resulting in an unhandled interrupt. * stm32-adc - off by one error on max channels checking. * stm32-timer - preset should not be buffered - reorganising register writes avoids this. - fix a corner case in which write preset goes wrong when a timer is used first as a trigger then as a counter with preset. Odd case but you never know. * ti-ads1015 - Fix setting of comparator polarity by fixing bitfield definition. * twl4030 - Error path handling fix to cleanup in event of regulator registration failure. - Disable the vusb3v1 regulator correctly in error handling - Don't paper over a regulator enable failure.

iio: ad_sigma_delta: Implement a dedicated reset function

2017-09-24T15:58:21Z

Since most of the SD ADCs have the option of reseting the serial interface by sending a number of SCLKs with CS = 0 and DIN = 1, a dedicated function that can do this is usefull. Needed for the patch: iio: ad7793: Fix the serial interface reset Signed-off-by: Dragos Bogdan Acked-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron

Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

2017-09-07T20:51:13Z

Pull MFD updates from Lee Jones: "New Drivers - RK805 Power Management IC (PMIC) - ROHM BD9571MWV-M MFD Power Management IC (PMIC) - Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs New Device Support: - Add support for HiSilicon Hi6421v530 to hi6421-pmic-core - Add support for X-Powers AXP806 to axp20x - Add support for X-Powers AXP813 to axp20x - Add support for Intel Sunrise Point LPSS to intel-lpss-pci New Functionality: - Amend API to provide register layout; atmel-smc Fix-ups: - DT re-work; omap, nokia - Header file location change {I2C => MFD}; dm355evm_msp, tps65010 - Fix chip ID formatting issue(s); rk808 - Optionally register touchscreen devices; da9052-core - Documentation improvements; twl-core - Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi - Drop unnecessary static declaration; max8925-i2c - Kconfig changes (missing deps and remove module support) - Slim down oversized licence statement; hi6421-pmic-core - Use managed resources (devm_*); lp87565 - Supply proper error checking/handling; t7l66xb Bug Fixes: - Fix counter duplication issue; da9052-core - Fix potential NULL deference issue; max8998 - Leave SPI-NOR write-protection bit alone; lpc_ich - Ensure device is put into reset during suspend; intel-lpss - Correct register offset variable size; omap-usb-tll" * tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits) mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT dt-bindings: mfd: Add bindings for ZII RAVE devices mfd: omap-usb-tll: Fix register offsets mfd: da9052: Constify spi_device_id mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend mfd: da9055: Constify i2c_device_id mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices mfd: t7l66xb: Handle return value of clk_prepare_enable mfd: Add ROHM BD9571MWV-M PMIC DT bindings mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool mfd: lp87565: Convert to use devm_mfd_add_devices() mfd: Add support for TPS68470 device mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell mfd: syscon: atmel-smc: Add helper to retrieve register layout mfd: axp20x: Use correct platform device ID for many PEK dt-bindings: mfd: axp20x: Introduce bindings for AXP813 mfd: axp20x: Add support for AXP813 PMIC dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips mfd: Add ROHM BD9571MWV-M MFD PMIC driver ...

iio: trigger: Add STM32 LPTimer trigger driver

2017-09-04T13:49:23Z

Add support for LPTIMx_OUT triggers that can be found on some STM32 devices. These triggers can be used then by ADC or DAC. Typical usage is to configure LPTimer as PWM output (via pwm-stm32-lp) and have synchronised analog conversions with these triggers. Signed-off-by: Fabrice Gasnier Reviewed-by: Jonathan Cameron Signed-off-by: Lee Jones