user/sven/linux.git/include/linux/input, branch v4.3.4

Input: pixcir_i2c_ts - move platform data

2015-07-12T00:27:36Z

Let's move driver's platform data definitions from include/linux/input/ into include/linux/platform_data/ so that it stays with the rest of platform data definitions. Acked-by: Roger Quadros Signed-off-by: Dmitry Torokhov

Input: of_touchscreen - switch to using device properties

2015-07-12T00:26:45Z

Let's switch form OF to device properties so that common parsing code could work not only on device tree but also on ACPI-based platforms. Reviewed-by: Roger Quadros Signed-off-by: Dmitry Torokhov

Input: improve parsing OF parameters for touchscreens

2015-06-25T21:45:46Z

When applying touchscreen parameters specified in device tree let's make sure we keep whatever setup was done by the driver and not reset the missing values to zero. Reported-by: Pavel Machek Tested-by: Pavel Machek Signed-off-by: Dmitry Torokhov

Input: MT - add support for balanced slot assignment

2015-02-01T19:50:35Z

Some devices are not fast enough to differentiate between a fast-moving contact and a new contact. This problem cannot be fully resolved because information is truly missing, but it is possible to safe-guard against obvious mistakes by restricting movement with a maximum displacement. The new problem formulation for dmax > 0 cannot benefit from the speedup for positive definite matrices, but since the convergence is faster, the result is about the same. For a handful of contacts, the latency difference is truly negligible. Suggested-by: Benjamin Tissoires Tested-by: Benjamin Tissoires Signed-off-by: Henrik Rydberg Signed-off-by: Dmitry Torokhov

Input: MT - make slot cleanup callable outside mt_sync_frame()

2014-08-08T06:37:07Z

Some semi-mt drivers use the slots in a manual way, but may still want to call parts of the frame synchronization logic. This patch makes input_mt_drop_unused callable from those drivers. Signed-off-by: Henrik Rydberg Reviewed-by: Benson Leung Signed-off-by: Dmitry Torokhov

Input: pixcir_i2c_ts - support up to 5 fingers and hardware tracking IDs

2014-07-28T17:26:18Z

Some variants of the Pixcir touch controller support up to 5 simultaneous fingers and hardware tracking IDs. Prepare the driver for that. Signed-off-by: Roger Quadros Signed-off-by: Dmitry Torokhov

Input: add common DT binding for touchscreens

2014-05-29T07:05:59Z

Add common DT binding documentation for touchscreen devices and implement input_parse_touchscreen_of_params, which parses the common properties and configures the input device accordingly. The method currently does not interpret the axis inversion properties, since there is no matching flag in the generic linux input device. Reviewed-by: Pavel Machek Acked-by: Aaro Koskinen Signed-off-by: Sebastian Reichel Signed-off-by: Dmitry Torokhov

Input: pixcir_i2c_ts - get rid of pdata->attb_read_val()

2014-05-19T06:25:57Z

Get rid of the attb_read_val() platform hook. Instead, read the ATTB gpio directly from the driver. Fail if valid ATTB gpio is not provided by patform data. Signed-off-by: Roger Quadros Acked-by: Mugunthan V N Signed-off-by: Dmitry Torokhov

Input: pixcir_i2c_ts - initialize interrupt mode and power mode

2014-05-19T06:25:56Z

Introduce helper functions to configure power and interrupt registers. Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode on detecting finger touch. Configure interrupt mode and polarity on start up. Power down on device closure or module removal. Signed-off-by: Roger Quadros Acked-by: Mugunthan V N Signed-off-by: Dmitry Torokhov

Input: pmic8xxx-pwrkey - migrate to DT

2014-03-30T20:25:19Z

The driver is only supported on DT enabled platforms. Convert the driver to DT so that it can probe properly. Signed-off-by: Stephen Boyd Signed-off-by: Dmitry Torokhov