user/sven/linux.git/include/linux/kasan.h, branch v4.19.153

kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN

2018-08-17T23:20:30Z

KASAN learns about hotadded memory via the memory hotplug notifier. devm_memremap_pages() intentionally skips calling memory hotplug notifiers. So KASAN doesn't know anything about new memory added by devm_memremap_pages(). This causes a crash when KASAN tries to access non-existent shadow memory: BUG: unable to handle kernel paging request at ffffed0078000000 RIP: 0010:check_memory_region+0x82/0x1e0 Call Trace: memcpy+0x1f/0x50 pmem_do_bvec+0x163/0x720 pmem_make_request+0x305/0xac0 generic_make_request+0x54f/0xcf0 submit_bio+0x9c/0x370 submit_bh_wbc+0x4c7/0x700 block_read_full_page+0x5ef/0x870 do_read_cache_page+0x2b8/0xb30 read_dev_sector+0xbd/0x3f0 read_lba.isra.0+0x277/0x670 efi_partition+0x41a/0x18f0 check_partition+0x30d/0x5e9 rescan_partitions+0x18c/0x840 __blkdev_get+0x859/0x1060 blkdev_get+0x23f/0x810 __device_add_disk+0x9c8/0xde0 pmem_attach_disk+0x9a8/0xf50 nvdimm_bus_probe+0xf3/0x3c0 driver_probe_device+0x493/0xbd0 bus_for_each_drv+0x118/0x1b0 __device_attach+0x1cd/0x2b0 bus_probe_device+0x1ac/0x260 device_add+0x90d/0x1380 nd_async_device_register+0xe/0x50 async_run_entry_fn+0xc3/0x5d0 process_one_work+0xa0a/0x1810 worker_thread+0x87/0xe80 kthread+0x2d7/0x390 ret_from_fork+0x3a/0x50 Add kasan_add_zero_shadow()/kasan_remove_zero_shadow() - post mm_init() interface to map/unmap kasan_zero_page at requested virtual addresses. And use it to add/remove the shadow memory for hotplugged/unplugged device memory. Link: http://lkml.kernel.org/r/20180629164932.740-1-aryabinin@virtuozzo.com Fixes: 41e94a851304 ("add devm_memremap_pages") Signed-off-by: Andrey Ryabinin Reported-by: Dave Chinner Reviewed-by: Dan Williams Tested-by: Dan Williams Cc: Dmitry Vyukov Cc: Alexander Potapenko Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

kasan: make kasan_cache_create() work with 32-bit slab cache sizes

2018-04-06T04:36:24Z

If SLAB doesn't support 4GB+ kmem caches (it never did), KASAN should not do it as well. Link: http://lkml.kernel.org/r/20180305200730.15812-20-adobriyan@gmail.com Signed-off-by: Alexey Dobriyan Cc: Andrey Ryabinin Cc: Alexander Potapenko Cc: Dmitry Vyukov Cc: Christoph Lameter Cc: Pekka Enberg Cc: David Rientjes Cc: Joonsoo Kim Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

x86/mm: Make PGDIR_SHIFT and PTRS_PER_P4D variable

2018-02-14T12:11:14Z

For boot-time switching between 4- and 5-level paging we need to be able to fold p4d page table level at runtime. It requires variable PGDIR_SHIFT and PTRS_PER_P4D. The change doesn't affect the kernel image size much: text data bss dec hex filename 8628091 4734304 1368064 14730459 e0c4db vmlinux.before 8628393 4734340 1368064 14730797 e0c62d vmlinux.after Signed-off-by: Kirill A. Shutemov Cc: Andy Lutomirski Cc: Borislav Petkov Cc: Linus Torvalds Cc: Peter Zijlstra Cc: Thomas Gleixner Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180214111656.88514-7-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar

kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage

2018-02-07T02:32:43Z

Right now the fact that KASAN uses a single shadow byte for 8 bytes of memory is scattered all over the code. This change defines KASAN_SHADOW_SCALE_SHIFT early in asm include files and makes use of this constant where necessary. [akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/34937ca3b90736eaad91b568edf5684091f662e3.1515775666.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov Acked-by: Andrey Ryabinin Cc: Dmitry Vyukov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

kasan: detect invalid frees for large mempool objects

2018-02-07T02:32:43Z

Detect frees of pointers into middle of mempool objects. I did a one-off test, but it turned out to be very tricky, so I reverted it. First, mempool does not call kasan_poison_kfree() unless allocation function fails. I stubbed an allocation function to fail on second and subsequent allocations. But then mempool stopped to call kasan_poison_kfree() at all, because it does it only when allocation function is mempool_kmalloc(). We could support this special failing test allocation function in mempool, but it also can't live with kasan tests, because these are in a module. Link: http://lkml.kernel.org/r/bf7a7d035d7a5ed62d2dd0e3d2e8a4fcdf456aa7.1514378558.git.dvyukov@google.com Signed-off-by: Dmitry Vyukov Cc: Andrey Ryabinin a Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

kasan: don't use __builtin_return_address(1)

2018-02-07T02:32:43Z

__builtin_return_address(1) is unreliable without frame pointers. With defconfig on kmalloc_pagealloc_invalid_free test I am getting: BUG: KASAN: double-free or invalid-free in (null) Pass caller PC from callers explicitly. Link: http://lkml.kernel.org/r/9b01bc2d237a4df74ff8472a3bf6b7635908de01.1514378558.git.dvyukov@google.com Signed-off-by: Dmitry Vyukov Cc: Andrey Ryabinin a Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

kasan: detect invalid frees for large objects

2018-02-07T02:32:42Z

Patch series "kasan: detect invalid frees". KASAN detects double-frees, but does not detect invalid-frees (when a pointer into a middle of heap object is passed to free). We recently had a very unpleasant case in crypto code which freed an inner object inside of a heap allocation. This left unnoticed during free, but totally corrupted heap and later lead to a bunch of random crashes all over kernel code. Detect invalid frees. This patch (of 5): Detect frees of pointers into middle of large heap objects. I dropped const from kasan_kfree_large() because it starts propagating through a bunch of functions in kasan_report.c, slab/slub nearest_obj(), all of their local variables, fixup_red_left(), etc. Link: http://lkml.kernel.org/r/1b45b4fe1d20fc0de1329aab674c1dd973fee723.1514378558.git.dvyukov@google.com Signed-off-by: Dmitry Vyukov Cc: Andrey Ryabinin a Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

slab, slub, slob: add slab_flags_t

2017-11-16T02:21:01Z

Add sparse-checked slab_flags_t for struct kmem_cache::flags (SLAB_POISON, etc). SLAB is bloated temporarily by switching to "unsigned long", but only temporarily. Link: http://lkml.kernel.org/r/20171021100225.GA22428@avx2 Signed-off-by: Alexey Dobriyan Acked-by: Pekka Enberg Cc: Christoph Lameter Cc: David Rientjes Cc: Joonsoo Kim Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

kasan: report only the first error by default

2017-04-01T00:13:30Z

Disable kasan after the first report. There are several reasons for this: - Single bug quite often has multiple invalid memory accesses causing storm in the dmesg. - Write OOB access might corrupt metadata so the next report will print bogus alloc/free stacktraces. - Reports after the first easily could be not bugs by itself but just side effects of the first one. Given that multiple reports usually only do harm, it makes sense to disable kasan after the first one. If user wants to see all the reports, the boot-time parameter kasan_multi_shot must be used. [aryabinin@virtuozzo.com: wrote changelog and doc, added missing include] Link: http://lkml.kernel.org/r/20170323154416.30257-1-aryabinin@virtuozzo.com Signed-off-by: Mark Rutland Signed-off-by: Andrey Ryabinin Cc: Andrey Konovalov Cc: Alexander Potapenko Cc: Dmitry Vyukov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds