user/sven/linux.git/include/linux/mfd/samsung, branch v3.15.3

Merge remote-tracking branches 'regulator/topic/s5m8767', 'regulator/topic/st-pwm', 'regulator/topic/ti-abb', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps6507x', 'regulator/topic/tps65090' and 'regulator/topic/tps65217' into regulator-next

2014-03-26T16:58:18Z

regulator: s2mps11: Add set_suspend_disable for S2MPS14

2014-03-19T13:02:51Z

S2MPS14 regulators support suspend mode where their status is controlled by PWREN coming from SoC. This patch implements the set_suspend_disable for S2MPS14 regulators. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Mark Brown

mfd: Add support for S2MPA01 device

2014-03-18T10:56:17Z

Add the necessary entries required for S2MPA01 multi-function device. While at it also convert whitespaces to tabs in core.h. Signed-off-by: Sachin Kamat Signed-off-by: Lee Jones

mfd: sec-core: Silence compiler warning

2014-03-18T10:50:20Z

When used 64bit compiler GCC warns as drivers/mfd/sec-core.c:199:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] Signed-off-by: Pankaj Dubey Signed-off-by: Lee Jones

mfd: sec: Add support for S2MPS14

2014-03-18T10:50:09Z

Add support for S2MPS14 PMIC device to the MFD sec-core driver. The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two clocks instead of three and a little different registers layout. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Lee Jones

mfd: sec-irq: Use consistent S2MPS11 RTC alarm interrupt indexes

2014-03-18T10:49:52Z

The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding interrupts are named similarly). Use consistent names for interrupts to limit possible errors. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Lee Jones

mfd: sec-core: Add maximum RTC register for regmap config

2014-03-18T10:48:43Z

Add maximum register to the regmap used by rtc-s5m driver. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Lee Jones

regulator: s5m8767: Use GPIO for controlling Buck9/eMMC

2014-01-27T20:24:17Z

Add support for GPIO control (enable/disable) over Buck9. The Buck9 Converter is used as a supply for eMMC Host Controller. BUCK9EN GPIO of S5M8767 chip may be used by application processor to enable or disable the Buck9. This has two benefits: - It is faster than toggling it over I2C bus. - It allows disabling the regulator during suspend to RAM; The AP will enable it during resume; Without the patch the regulator supplying eMMC must be defined as fixed-regulator. Signed-off-by: Krzysztof Kozlowski Acked-by: Lee Jones Signed-off-by: Mark Brown

mfd: sec: Remove sec_reg* regmap helpers

2013-12-18T17:25:26Z

Remove sec_reg* helpers as they are not used anymore. These helpers were error-prone as they mixed u8 with unsigned int and they changed order of some of parameters (val and mask in sec_reg_update()). Also the helpers didn't give any way of useful abstraction as they just called corresponding regmap function. Signed-off-by: Krzysztof Kozlowski Acked-by: Lee Jones Signed-off-by: Mark Brown

Merge tag 's2mps11-build' into regulator-s5m8767 since a following patch

2013-12-18T17:24:41Z

depend on it. regulator/clk: Fix s2mps11 build This patch fixes a build failure that appeared in v3.13-rc4 due to an RTC/MFD update merged via -mm.