user/sven/linux.git/include/linux/mlx5, branch v6.1.56

RDMA/mlx5: Fix affinity assignment

2023-06-21T14:01:00Z

[ Upstream commit 617f5db1a626f18d5cbb7c7faf7bf8f9ea12be78 ] The cited commit aimed to ensure that Virtual Functions (VFs) assign a queue affinity to a Queue Pair (QP) to distribute traffic when the LAG master creates a hardware LAG. If the affinity was set while the hardware was not in LAG, the firmware would ignore the affinity value. However, this commit unintentionally assigned an affinity to QPs on the LAG master's VPORT even if the RDMA device was not marked as LAG-enabled. In most cases, this was not an issue because when the hardware entered hardware LAG configuration, the RDMA device of the LAG master would be destroyed and a new one would be created, marked as LAG-enabled. The problem arises when a user configures Equal-Cost Multipath (ECMP). In ECMP mode, traffic can be directed to different physical ports based on the queue affinity, which is intended for use by VPORTS other than the E-Switch manager. ECMP mode is supported only if both E-Switch managers are in switchdev mode and the appropriate route is configured via IP. In this configuration, the RDMA device is not destroyed, and we retain the RDMA device that is not marked as LAG-enabled. To ensure correct behavior, Send Queues (SQs) opened by the E-Switch manager through verbs should be assigned strict affinity. This means they will only be able to communicate through the native physical port associated with the E-Switch manager. This will prevent the firmware from assigning affinity and will not allow the SQs to be remapped in case of failover. Fixes: 802dcc7fc5ec ("RDMA/mlx5: Support TX port affinity for VF drivers in LAG mode") Reviewed-by: Maor Gottlieb Signed-off-by: Mark Bloch Link: https://lore.kernel.org/r/425b05f4da840bc684b0f7e8ebf61aeb5cef09b0.1685960567.git.leon@kernel.org Signed-off-by: Leon Romanovsky Signed-off-by: Sasha Levin

net/mlx5: DR, Check force-loopback RC QP capability independently from RoCE

2023-05-30T13:03:33Z

commit c7dd225bc224726c22db08e680bf787f60ebdee3 upstream. SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB (loopback), and FL (force-loopback) QP is preferred for performance. FL is available when RoCE is enabled or disabled based on RoCE caps. This patch adds reading of FL capability from HCA caps in addition to the existing reading from RoCE caps, thus fixing the case where we didn't have loopback enabled when RoCE was disabled. Fixes: 7304d603a57a ("net/mlx5: DR, Add support for force-loopback QP") Signed-off-by: Itamar Gozlan Signed-off-by: Yevgeny Kliteynik Signed-off-by: Saeed Mahameed Signed-off-by: Greg Kroah-Hartman

RDMA/mlx5: Fix flow counter query via DEVX

2023-05-11T14:03:35Z

[ Upstream commit 3e358ea8614ddfbc59ca7a3f5dff5dde2b350b2c ] Commit cited in "fixes" tag added bulk support for flow counters but it didn't account that's also possible to query a counter using a non-base id if the counter was allocated as bulk. When a user performs a query, validate the flow counter id given in the mailbox is inside the valid range taking bulk value into account. Fixes: 208d70f562e5 ("IB/mlx5: Support flow counters offset for bulk counters") Signed-off-by: Mark Bloch Reviewed-by: Maor Gottlieb Link: https://lore.kernel.org/r/79d7fbe291690128e44672418934256254d93115.1681377114.git.leon@kernel.org Signed-off-by: Leon Romanovsky Signed-off-by: Sasha Levin

net/mlx5: Expose SF firmware pages counter

2023-02-14T18:11:47Z

[ Upstream commit 9965bbebae59b3563a4d95e4aed121e8965dfdc2 ] Currently, each core device has VF pages counter which stores number of fw pages used by its VFs and SFs. The current design led to a hang when performing firmware reset on DPU, where the DPU PFs stalled in sriov unload flow due to waiting on release of SFs pages instead of waiting on only VFs pages. Thus, Add a separate counter for SF firmware pages, which will prevent the stall scenario described above. Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver") Signed-off-by: Maher Sanalla Reviewed-by: Shay Drory Signed-off-by: Saeed Mahameed Signed-off-by: Sasha Levin

net/mlx5: Store page counters in a single array

2023-02-14T18:11:47Z

[ Upstream commit c3bdbaea654d8df39112de33037106134a520dc7 ] Currently, an independent page counter is used for tracking memory usage for each function type such as VF, PF and host PF (DPU). For better code-readibilty, use a single array that stores the number of allocated memory pages for each function type. Signed-off-by: Maher Sanalla Reviewed-by: Shay Drory Signed-off-by: Saeed Mahameed Stable-dep-of: 9965bbebae59 ("net/mlx5: Expose SF firmware pages counter") Signed-off-by: Sasha Levin

net/mlx5: Fix command stats access after free

2023-01-18T10:58:29Z

[ Upstream commit da2e552b469a0cd130ff70a88ccc4139da428a65 ] Command may fail while driver is reloading and can't accept FW commands till command interface is reinitialized. Such command failure is being logged to command stats. This results in NULL pointer access as command stats structure is being freed and reallocated during mlx5 devlink reload (see kernel log below). Fix it by making command stats statically allocated on driver probe. Kernel log: [ 2394.808802] BUG: unable to handle kernel paging request at 000000000002a9c0 [ 2394.810610] PGD 0 P4D 0 [ 2394.811811] Oops: 0002 [#1] SMP NOPTI ... [ 2394.815482] RIP: 0010:native_queued_spin_lock_slowpath+0x183/0x1d0 ... [ 2394.829505] Call Trace: [ 2394.830667] _raw_spin_lock_irq+0x23/0x26 [ 2394.831858] cmd_status_err+0x55/0x110 [mlx5_core] [ 2394.833020] mlx5_access_reg+0xe7/0x150 [mlx5_core] [ 2394.834175] mlx5_query_port_ptys+0x78/0xa0 [mlx5_core] [ 2394.835337] mlx5e_ethtool_get_link_ksettings+0x74/0x590 [mlx5_core] [ 2394.836454] ? kmem_cache_alloc_trace+0x140/0x1c0 [ 2394.837562] __rh_call_get_link_ksettings+0x33/0x100 [ 2394.838663] ? __rtnl_unlock+0x25/0x50 [ 2394.839755] __ethtool_get_link_ksettings+0x72/0x150 [ 2394.840862] duplex_show+0x6e/0xc0 [ 2394.841963] dev_attr_show+0x1c/0x40 [ 2394.843048] sysfs_kf_seq_show+0x9b/0x100 [ 2394.844123] seq_read+0x153/0x410 [ 2394.845187] vfs_read+0x91/0x140 [ 2394.846226] ksys_read+0x4f/0xb0 [ 2394.847234] do_syscall_64+0x5b/0x1a0 [ 2394.848228] entry_SYSCALL_64_after_hwframe+0x65/0xca Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs") Signed-off-by: Moshe Shemesh Reviewed-by: Shay Drory Signed-off-by: Saeed Mahameed Signed-off-by: Sasha Levin

net/mlx5: E-Switch, properly handle ingress tagged packets on VST

2023-01-12T11:02:09Z

[ Upstream commit 1f0ae22ab470946143485a02cc1cd7e05c0f9120 ] Fix SRIOV VST mode behavior to insert cvlan when a guest tag is already present in the frame. Previous VST mode behavior was to drop packets or override existing tag, depending on the device version. In this patch we fix this behavior by correctly building the HW steering rule with a push vlan action, or for older devices we ask the FW to stack the vlan when a vlan is already present. Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes") Fixes: dfcb1ed3c331 ("net/mlx5: E-Switch, Vport ingress/egress ACLs rules for VST mode") Signed-off-by: Moshe Shemesh Reviewed-by: Mark Bloch Signed-off-by: Saeed Mahameed Signed-off-by: Sasha Levin

net/mlx5: cmdif, Print info on any firmware cmd failure to tracepoint

2022-11-22T02:14:34Z

While moving to new CMD API (quiet API), some pre-existing flows may call the new API function that in case of error, returns the error instead of printing it as previously done. For such flows we bring back the print but to tracepoint this time for sys admins to have the ability to check for errors especially for commands using the new quiet API. Tracepoint output example: devlink-1333 [001] ..... 822.746922: mlx5_cmd: ACCESS_REG(0x805) op_mod(0x0) failed, status bad resource(0x5), syndrome (0xb06e1f), err(-22) Fixes: f23519e542e5 ("net/mlx5: cmdif, Add new api for command execution") Signed-off-by: Moshe Shemesh Reviewed-by: Shay Drory Reviewed-by: Maor Gottlieb Signed-off-by: Saeed Mahameed

net/mlx5: Fix possible use-after-free in async command interface

2022-10-27T18:06:56Z

mlx5_cmd_cleanup_async_ctx should return only after all its callback handlers were completed. Before this patch, the below race between mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and lead to a use-after-free: 1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e. elevated by 1, a single inflight callback). 2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1. 3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and is about to call wake_up(). 4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns immediately as the condition (num_inflight == 0) holds. 5. mlx5_cmd_cleanup_async_ctx returns. 6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx object. 7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed object. Fix it by syncing using a completion object. Mark it completed when num_inflight reaches 0. Trace: BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270 Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0 CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: dump_stack_lvl+0x57/0x7d print_report.cold+0x2d5/0x684 ? do_raw_spin_lock+0x23d/0x270 kasan_report+0xb1/0x1a0 ? do_raw_spin_lock+0x23d/0x270 do_raw_spin_lock+0x23d/0x270 ? rwlock_bug.part.0+0x90/0x90 ? __delete_object+0xb8/0x100 ? lock_downgrade+0x6e0/0x6e0 _raw_spin_lock_irqsave+0x43/0x60 ? __wake_up_common_lock+0xb9/0x140 __wake_up_common_lock+0xb9/0x140 ? __wake_up_common+0x650/0x650 ? destroy_tis_callback+0x53/0x70 [mlx5_core] ? kasan_set_track+0x21/0x30 ? destroy_tis_callback+0x53/0x70 [mlx5_core] ? kfree+0x1ba/0x520 ? do_raw_spin_unlock+0x54/0x220 mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core] ? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core] ? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core] mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core] ? dump_command+0xcc0/0xcc0 [mlx5_core] ? lockdep_hardirqs_on_prepare+0x400/0x400 ? cmd_comp_notifier+0x7e/0xb0 [mlx5_core] cmd_comp_notifier+0x7e/0xb0 [mlx5_core] atomic_notifier_call_chain+0xd7/0x1d0 mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core] atomic_notifier_call_chain+0xd7/0x1d0 ? irq_release+0x140/0x140 [mlx5_core] irq_int_handler+0x19/0x30 [mlx5_core] __handle_irq_event_percpu+0x1f2/0x620 handle_irq_event+0xb2/0x1d0 handle_edge_irq+0x21e/0xb00 __common_interrupt+0x79/0x1a0 common_interrupt+0x78/0xa0 asm_common_interrupt+0x22/0x40 RIP: 0010:default_idle+0x42/0x60 Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00 RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242 RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110 RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3 R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005 R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000 ? default_idle_call+0xcc/0x450 default_idle_call+0xec/0x450 do_idle+0x394/0x450 ? arch_cpu_idle_exit+0x40/0x40 ? do_idle+0x17/0x450 cpu_startup_entry+0x19/0x20 start_secondary+0x221/0x2b0 ? set_cpu_sibling_map+0x2070/0x2070 secondary_startup_64_no_verify+0xcd/0xdb Allocated by task 49502: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 kvmalloc_node+0x48/0xe0 mlx5e_bulk_async_init+0x35/0x110 [mlx5_core] mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core] mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core] mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core] mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core] mlx5e_suspend+0xdb/0x140 [mlx5_core] mlx5e_remove+0x89/0x190 [mlx5_core] auxiliary_bus_remove+0x52/0x70 device_release_driver_internal+0x40f/0x650 driver_detach+0xc1/0x180 bus_remove_driver+0x125/0x2f0 auxiliary_driver_unregister+0x16/0x50 mlx5e_cleanup+0x26/0x30 [mlx5_core] cleanup+0xc/0x4e [mlx5_core] __x64_sys_delete_module+0x2b5/0x450 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Freed by task 49502: kasan_save_stack+0x1e/0x40 kasan_set_track+0x21/0x30 kasan_set_free_info+0x20/0x30 ____kasan_slab_free+0x11d/0x1b0 kfree+0x1ba/0x520 mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core] mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core] mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core] mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core] mlx5e_suspend+0xdb/0x140 [mlx5_core] mlx5e_remove+0x89/0x190 [mlx5_core] auxiliary_bus_remove+0x52/0x70 device_release_driver_internal+0x40f/0x650 driver_detach+0xc1/0x180 bus_remove_driver+0x125/0x2f0 auxiliary_driver_unregister+0x16/0x50 mlx5e_cleanup+0x26/0x30 [mlx5_core] cleanup+0xc/0x4e [mlx5_core] __x64_sys_delete_module+0x2b5/0x450 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Fixes: e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API") Signed-off-by: Tariq Toukan Reviewed-by: Moshe Shemesh Signed-off-by: Saeed Mahameed Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org Signed-off-by: Jakub Kicinski

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma

2022-10-07T19:05:29Z

Pull rdma updates from Jason Gunthorpe: "Not a big list of changes this cycle, mostly small things. The new MANA rdma driver should come next cycle along with a bunch of work on rxe. Summary: - Small bug fixes in mlx5, efa, rxe, hns, irdma, erdma, siw - rts tracing improvements - Code improvements: strlscpy conversion, unused parameter, spelling mistakes, unused variables, flex arrays - restrack device details report for hns - Simplify struct device initialization in SRP - Eliminate the never-used service_mask support in IB CM - Make rxe not print to the console for some kinds of network packets - Asymetric paths and router support in the CM through netlink messages - DMABUF importer support for mlx5devx umem's" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (84 commits) RDMA/rxe: Remove error/warning messages from packet receiver path RDMA/usnic: fix set-but-not-unused variable 'flags' warning IB/hfi1: Use skb_put_data() instead of skb_put/memcpy pair RDMA/hns: Unified Log Printing Style RDMA/hns: Replacing magic number with macros in apply_func_caps() RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data() RDMA/hns: Remove redundant 'max_srq_desc_sz' in caps RDMA/hns: Remove redundant 'num_mtt_segs' and 'max_extend_sg' RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt() RDMA/hns: Remove redundant 'use_lowmem' argument from hns_roce_init_hem_table() RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item() RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init() RDMA/hns: Remove unnecessary brackets when getting point RDMA/hns: Remove unnecessary braces for single statement blocks RDMA/hns: Cleanup for a spelling error of Asynchronous IB/rdmavt: Add __init/__exit annotations to module init/exit funcs RDMA/rxe: Remove redundant num_sge fields RDMA/mlx5: Enable ATS support for MRs and umems RDMA/mlx5: Add support for dmabuf to devx umem RDMA/core: Add UVERBS_ATTR_RAW_FD ...