user/sven/linux.git/include/linux/mmc/mmc.h, branch v3.16.52

mmc: add support for HS400 mode of eMMC5.0

2014-05-12T22:06:06Z

This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon Reviewed-by: Jackey Shen Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: rework selection of bus speed mode

2014-05-12T22:06:04Z

Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by: Seungwon Jeon Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: identify available device type to select

2014-05-12T22:05:57Z

Device types which are supported by both host and device can be identified when EXT_CSD is read. There is no need to check host's capability anymore. Signed-off-by: Seungwon Jeon Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: add packed command feature of eMMC4.5

2013-02-24T19:37:15Z

This patch adds packed command feature of eMMC4.5. The maximum number for packing read (or write) is offered and exception event relevant to packed command which is used for error handling is enabled. If host wants to use this feature, MMC_CAP2_PACKED_CMD should be set. Signed-off-by: Seungwon Jeon Reviewed-by: Maya Erez Reviewed-by: Subhash Jadavani Reviewed-by: Namjae Jeon Signed-off-by: Chris Ball

mmc: core: Expose access to RPMB partition

2012-12-06T18:54:46Z

Following JEDEC standard, if the mmc supports RPMB partition, a new interface is created and exposed via /dev/block. Users will be able to access RPMB partition using standard mmc IOCTL commands. Signed-off-by: Alex Macro Signed-off-by: Loic Pallardy Reviewed-by: Namjae Jeon Acked-by: Linus Walleij Acked-by: Johan Rudholm Acked-by: Krishna Konda Signed-off-by: Chris Ball

mmc: support BKOPS feature for eMMC

2012-10-03T14:05:12Z

Enable eMMC background operations (BKOPS) feature. If URGENT_BKOPS is set after a response, note that BKOPS are required. Immediately run BKOPS if required. Read/write operations should be requested during BKOPS(LEVEL-1), then issue HPI to interrupt the ongoing BKOPS and service the foreground operation. (This patch only controls the LEVEL2/3.) When repeating the writing 1GB data, at a certain time, performance is decreased. At that time, card triggers the Level-3 or Level-2. After running bkops, performance is recovered. Future considerations: * Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner. * Interrupt ongoing BKOPS before powering off the card. * How do we get BKOPS_STATUS value (periodically send ext_csd command)? * If using periodic bkops, also consider runtime_pm control. Signed-off-by: Jaehoon Chung Signed-off-by: Kyungmin Park Signed-off-by: Konstantin Dorfman Reviewed-by: Maya Erez Signed-off-by: Chris Ball

mmc: core: fix the decision of HS200/DDR card-type

2012-05-09T14:03:21Z

Current implementation decides the card type exclusively. Even though eMMC device can support both HS200 and DDR mode, card type will be set only for HS200. If the host doesn't support HS200 but has DDR capability, then DDR mode can't be selected. Signed-off-by: Seungwon Jeon Reviewed-by: Subhash Jadavani Signed-off-by: Chris Ball

mmc: MMC-4.5 Data Tag Support

2012-03-25T23:33:44Z

MMC-4.5 data tag feature will be used to store the file system meta-data in the tagged region of eMMC. This will improve the write and subsequent read transfer time for the meta data. Signed-off-by: Saugata Das Tested-by: Venkatraman S Signed-off-by: Chris Ball

mmc: core: HS200 mode support for eMMC 4.5

2012-01-12T20:17:15Z

This patch adds the support of the HS200 bus speed for eMMC 4.5 devices. The eMMC 4.5 devices have support for 200MHz bus speed. The function prototype of the tuning function is modified to handle the tuning command number which is different in sd and mmc case. Signed-off-by: Girish K S Signed-off-by: Philip Rakity Signed-off-by: Chris Ball

mmc: boot partition ro lock support

2012-01-12T04:58:43Z

Enable boot partitions to be read-only locked until next power on via a sysfs entry. There will be one sysfs entry for each boot partition: /sys/block/mmcblkXbootY/ro_lock_until_next_power_on Each boot partition is locked by writing 1 to its file. Signed-off-by: Johan Rudholm Signed-off-by: John Beckett Signed-off-by: Chris Ball