user/sven/linux.git/include/linux/mmc/mmc.h, branch v4.4.27

mmc: mmc: Add driver strength selection

2015-06-01T07:07:14Z

Add the ability to set eMMC driver strength for HS200 and HS400. Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: mmc: Read card's valid driver strength mask

2015-06-01T07:07:13Z

In preparation for supporing drive strength selection for eMMC, read the card's valid driver strengths. Note that though the SD spec uses the term "drive strength", the JEDEC eMMC spec uses the term "driver strength". Signed-off-by: Adrian Hunter Signed-off-by: Ulf Hansson

mmc: Resolve BKOPS compatability issue

2015-01-29T10:15:12Z

This patch is coming to fix compatibility issue of BKOPS_EN field of EXT_CSD. In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits: Bit 0 - MANUAL_EN Bit 1 - AUTO_EN In previous eMMC revisions, only Bit 0 was supported. Signed-off-by: Alexey Skidanov Signed-off-by: Ulf Hansson

mmc: core: Make tuning block patterns static

2015-01-19T08:56:24Z

Since previous patches removed the need for the tuning block patterns to be exported, let's move them close to the mmc_send_tuning() API. Those are now intended to be used only by the mmc core. Signed-off-by: Ulf Hansson Reviewed-by: Stephen Boyd Acked-by: Jaehoon Chung

mmc: core: Report firmware version for eMMC 5.0 devices.

2014-11-10T11:40:36Z

For eMMC 5.0 compliant device, firmware version is stored in ext_csd. Report firmware as a 64bit hexa decimal. Vendor can use hexa or ascii string to report firmware version. Also add FFU related EXT_CSD register and note if the device is FFU capable. Signed-off-by: Gwendal Grignou Signed-off-by: Ulf Hansson

mmc: Consolidate emmc tuning blocks

2014-09-23T07:13:19Z

The same tuning block exists in the dw_mmc h.c and sdhci-msm.c files. Move these into mmc.c so that they can be shared across drivers. Reported-by: Jaehoon Chung Signed-off-by: Stephen Boyd Signed-off-by: Ulf Hansson

mmc: Replace "enhanced_area_en" attribute by "partition_setting_completed"

2014-09-18T22:03:36Z

Replace ext_csd "enhanced_area_en" attribute by "partition_setting_completed". It was used whether or not enhanced user area is defined and without checks of EXT_CSD_PARTITION_SETTING_COMPLETED bit. Signed-off-by: Grégory Soutadé Signed-off-by: Ulf Hansson

mmc: add support for HS400 mode of eMMC5.0

2014-05-12T22:06:06Z

This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon Reviewed-by: Jackey Shen Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: rework selection of bus speed mode

2014-05-12T22:06:04Z

Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by: Seungwon Jeon Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: identify available device type to select

2014-05-12T22:05:57Z

Device types which are supported by both host and device can be identified when EXT_CSD is read. There is no need to check host's capability anymore. Signed-off-by: Seungwon Jeon Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball