user/sven/linux.git/include/linux/mmc, branch v2.6.32.40

mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume

2011-05-09T22:55:31Z

commit 4c2ef25fe0b847d2ae818f74758ddb0be1c27d8e upstream. If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to suspend, the card will be removed, therefore this patch doesn't change the behavior of this option. However the removal will be done by pm notifier, which runs while userspace is still not frozen and thus can freely use del_gendisk, without the risk of deadlock which would happen otherwise. Card detect workqueue is now disabled while userspace is frozen, Therefore if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during suspend, the removal will be detected as soon as userspace is unfrozen, again at the moment it is safe to call del_gendisk. Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate. [akpm@linux-foundation.org: clean up function prototype] [akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Maxim Levitsky Cc: David Brownell Cc: Alan Stern Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds [bwh: Adjust for 2.6.32] Signed-off-by: Greg Kroah-Hartman

libertas/sdio: 8686: set ECSI bit for 1-bit transfers

2010-08-02T17:21:25Z

commit 8a64c0f6b7ec7f758c4ef445e49f479e27fa2236 upstream. When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line. However, the 8686 will only drive this line when the ECSI bit is set in the CCCR_IF register. Thanks to Alagu Sankar for pointing me in the right direction. Signed-off-by: Daniel Mack Cc: Alagu Sankar Cc: Volker Ernst Cc: Dan Williams Cc: John W. Linville Cc: Holger Schurig Cc: Bing Zhao Cc: libertas-dev@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: linux-mmc@vger.kernel.org Acked-by: Dan Williams Signed-off-by: John W. Linville Signed-off-by: Greg Kroah-Hartman

headers: remove sched.h from interrupt.h

2009-10-11T18:20:58Z

After m68k's task_thread_info() doesn't refer to current, it's possible to remove sched.h from interrupt.h and not break m68k! Many thanks to Heiko Carstens for allowing this. Signed-off-by: Alexey Dobriyan

mmc: make SDIO device/driver struct accessors public

2009-09-23T14:39:38Z

Especially with the PM framework, those are quite handy to have in driver code too. Signed-off-by: Nicolas Pitre Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

sdio: add MMC_QUIRK_LENIENT_FN0

2009-09-23T14:39:37Z

Normally writes to SDIO function 0 outside the vendor specific CCCR registers are prohibited. To support embedded devices that require writes to SDIO function 0 outside this range (e.g. TI WL127x embedded sdio wifi device), MMC_QUIRK_LENIENT_FN0 is introduced. A card quirks field is added to `struct mmc_card' to support non-standard devices (e.g. embedded sdio devices). [akpm@linux-foundation.org: code in C, not cpp!] Signed-off-by: Ohad Ben-Cohen Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

sdio: add CD disable support

2009-09-23T14:39:36Z

Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1) of the card. This may be desired on certain setups of boards, controllers and embedded sdio devices which do not need the card's pull-up. As a result, card detection is disabled and power is saved. [akpm@linux-foundation.org: simplify sdio_disable_cd() a bit] Signed-off-by: Ohad Ben-Cohen Acked-by: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Philip Langdale Cc: Pierre Ossman Cc: David Vrabel Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

mmc: check status after MMC SWITCH command

2009-09-23T14:39:34Z

According to the standard, the SWITCH command should be followed by a SEND_STATUS command to check for errors. Signed-off-by: Adrian Hunter Acked-by: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Jarkko Lavinen Cc: Denis Karpov Cc: Pierre Ossman Cc: Philip Langdale Cc: "Madhusudhan" Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

mmc: add mmc card sleep and awake support

2009-09-23T14:39:33Z

Add support for the new MMC command SLEEP_AWAKE. Signed-off-by: Jarkko Lavinen Signed-off-by: Adrian Hunter Acked-by: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Jarkko Lavinen Cc: Denis Karpov Cc: Pierre Ossman Cc: Philip Langdale Cc: "Madhusudhan" Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

mmc: add ability to save power by powering off cards

2009-09-23T14:39:33Z

Power can be saved by powering off cards that are not in use. This is similar to suspend / resume except it is under the control of the driver, and does not require any power management support. It can only be used when the driver can monitor whether the card is removed, otherwise it is unsafe. This is possible because, unlike suspend, the driver still receives card detect and / or cover switch interrupts. Signed-off-by: Adrian Hunter Acked-by: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Jarkko Lavinen Cc: Denis Karpov Cc: Pierre Ossman Cc: Philip Langdale Cc: "Madhusudhan" Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

mmc: add MMC_CAP_NONREMOVABLE host capability

2009-09-23T14:39:33Z

eMMC's are not removable, so unsafe resume is OK always. To permit this a new host capability MMC_CAP_NONREMOVABLE has been added and suspend / resume updated accordingly. Signed-off-by: Adrian Hunter Acked-by: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Jarkko Lavinen Cc: Denis Karpov Cc: Pierre Ossman Cc: Philip Langdale Cc: "Madhusudhan" Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds