user/sven/linux.git/include/linux/mmc, branch v3.2

mmc: core: Add quirk for long data read time

2011-12-10T21:18:35Z

Adds a quirk that sets the data read timeout to a fixed value instead of relying on the information in the CSD. The timeout value chosen is 300ms since that has proven enough for the problematic cards found, but could be increased if other cards require this. This patch also enables this quirk for certain Micron cards known to have this problem. Signed-off-by: Stefan Nilsson XK Signed-off-by: Ulf Hansson Acked-by: Linus Walleij Cc: Signed-off-by: Chris Ball

mmc: fix compile error when CONFIG_BLOCK is not enabled

2011-10-27T13:11:34Z

'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was introduced via genhd.h by the general purpose partition patch. To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using DISK_NAME_LEN. Reported-by: Randy Dunlap Signed-off-by: Namjae Jeon Acked-by: Randy Dunlap Acked-by: Andrei Warkentin Signed-off-by: Chris Ball

mmc: core: add workaround for controllers with broken multiblock reads

2011-10-27T13:10:57Z

Due to hardware bugs, some MMC host controllers don't support multiple-block reads[1]. To resolve, add a new MMC capability flag, MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller drivers. When this capability is set, all reads will be issued one sector at a time. 1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_ Revision F (October 2010) (SPRZ278F), available from http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf Signed-off-by: Paul Walmsley Cc: Dave Hylands Tested-by: Steve Sakoman Signed-off-by: Chris Ball

mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00

2011-10-26T20:32:31Z

Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified Specification Version 3.00, Feb. 25, 2011. This patch has been tested with Marvell WLAN device SD8797. Signed-off-by: Bing Zhao Signed-off-by: Chris Ball

mmc: core: support HPI send command

2011-10-26T20:32:29Z

HPI command is defined in eMMC4.41. This feature is important for eMMC4.5 devices. Signed-off-by: Jaehoon Chung Signed-off-by: Chris Ball

mmc: core: Add cache control for eMMC4.5 device

2011-10-26T20:32:28Z

This patch adds cache feature of eMMC4.5 Spec. If device supports cache capability, host can utilize some specific operations. Signed-off-by: Seungwon Jeon Signed-off-by: Jaehoon Chung Signed-off-by: Chris Ball

mmc: core: new discard feature support at eMMC v4.5

2011-10-26T20:32:27Z

MMC v4.5 supports the DISCARD feature (CMD38). It's different from trim and there's no check bit. Currently it's only supported at v4.5. Signed-off-by: Kyungmin Park Signed-off-by: Jaehoon Chung Signed-off-by: Chris Ball

mmc: core: mmc sanitize feature support for v4.5

2011-10-26T20:32:26Z

In the v4.5, there's no secure erase & trim support. Instead it supports the sanitize feature. Signed-off-by: Kyungmin Park Signed-off-by: Jaehoon Chung Signed-off-by: Chris Ball

mmc: dw_mmc: modify DATA register offset

2011-10-26T20:32:25Z

In dw_mmc 2.40a spec, Data register's offset is changed. Before we used Data register offset 0x100. but if somebody uses a 2.40a controller, we must use 0x200 for Data register. This patch adds a version-id checking point and uses SDMMC_DATA(x) instead of SDMMC_DATA. It assumes 2.40a is the latest version. Signed-off-by: Jaehoon Chung Signed-off-by: Kyungmin Park Acked-by: James Hogan Signed-off-by: Chris Ball

mmc: core: Add Power Off Notify Feature eMMC 4.5

2011-10-26T20:32:23Z

This patch adds support for the power off notify feature, available in eMMC 4.5 devices. If the host has support for this feature, then the mmc core will notify the device by setting the POWER_OFF_NOTIFICATION byte in the extended csd register with a value of 1 (POWER_ON). For suspend mode short timeout is used, whereas for the normal poweroff long timeout is used. Signed-off-by: Girish K S Signed-off-by: Jaehoon Chung Signed-off-by: Chris Ball