user/sven/linux.git/include/linux/mmc, branch v4.19.14

mmc: core: Drop the unused mmc_power_save|restore_host()

2018-07-16T09:21:45Z

The last user of mmc_power_save|restore_host() APIs is gone, hence let's drop them. Drop also the corresponding bus_ops callback, ->power_save|restore() as those becomes redundant. Cc: Tony Lindgren Cc: Eyal Reizer Signed-off-by: Ulf Hansson

mmc: core: more fine-grained hooks for HS400 tuning

2018-07-16T09:21:45Z

This adds two new HS400 tuning operations: * hs400_downgrade * hs400_complete These supplement the existing HS400 operation: * prepare_hs400_tuning This is motivated by a requirement of Renesas SDHI for the following: 1. Disabling SCC before selecting to HS if selection of HS400 has occurred. This can be done in an implementation of prepare_hs400_tuning_downgrade 2. Updating registers after switching to HS400 This can be done in an implementation of complete_hs400_tuning If hs400_downgrade or hs400_complete are not implemented then they are not called. Thus means there should be no affect for existing drivers as none implemt these ops. Signed-off-by: Simon Horman Signed-off-by: Ulf Hansson

mmc: core: Adjust and reuse the macro of R1_STATUS(x)

2018-07-16T09:21:45Z

R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(), which checks all bits as possible. But according to the spec, bit 17 and bit 18 should be ignored, as well bit 14 which is reserved(must be set to 0) quoting from the spec and these rule apply to all places checking the device status. So change its checking from 0xFFFFE000 to 0xFFF9A000. As a bonus, we reuse it for mmc_do_erase() as well as mmc_switch_status_error(). (1) Currently mmc_switch_status_error() doesn't check bit 25, but it means device is locked but not unlocked by CMD42 prior to any operations which need check busy, which is also not allowed. (2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP. The spec says "Only partial address space was erased due to existing write protected blocks.", which obviously means we should fail this I/O. Otherwise, the partial erased data stored in nonvalatile flash violates the data integrity from the view of I/O owner, which probably confuse it when further used. So reusing R1_STATUS for them not only improve the readability but also slove real problems. Signed-off-by: Shawn Lin Signed-off-by: Ulf Hansson

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2018-06-07T01:39:49Z

Pull networking updates from David Miller: 1) Add Maglev hashing scheduler to IPVS, from Inju Song. 2) Lots of new TC subsystem tests from Roman Mashak. 3) Add TCP zero copy receive and fix delayed acks and autotuning with SO_RCVLOWAT, from Eric Dumazet. 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard Brouer. 5) Add ttl inherit support to vxlan, from Hangbin Liu. 6) Properly separate ipv6 routes into their logically independant components. fib6_info for the routing table, and fib6_nh for sets of nexthops, which thus can be shared. From David Ahern. 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP messages from XDP programs. From Nikita V. Shirokov. 8) Lots of long overdue cleanups to the r8169 driver, from Heiner Kallweit. 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau. 10) Add traffic condition monitoring to iwlwifi, from Luca Coelho. 11) Plumb extack down into fib_rules, from Roopa Prabhu. 12) Add Flower classifier offload support to igb, from Vinicius Costa Gomes. 13) Add UDP GSO support, from Willem de Bruijn. 14) Add documentation for eBPF helpers, from Quentin Monnet. 15) Add TLS tx offload to mlx5, from Ilya Lesokhin. 16) Allow applications to be given the number of bytes available to read on a socket via a control message returned from recvmsg(), from Soheil Hassas Yeganeh. 17) Add x86_32 eBPF JIT compiler, from Wang YanQing. 18) Add AF_XDP sockets, with zerocopy support infrastructure as well. From Björn Töpel. 19) Remove indirect load support from all of the BPF JITs and handle these operations in the verifier by translating them into native BPF instead. From Daniel Borkmann. 20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha. 21) Allow XDP programs to do lookups in the main kernel routing tables for forwarding. From David Ahern. 22) Allow drivers to store hardware state into an ELF section of kernel dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy. 23) Various RACK and loss detection improvements in TCP, from Yuchung Cheng. 24) Add TCP SACK compression, from Eric Dumazet. 25) Add User Mode Helper support and basic bpfilter infrastructure, from Alexei Starovoitov. 26) Support ports and protocol values in RTM_GETROUTE, from Roopa Prabhu. 27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard Brouer. 28) Add lots of forwarding selftests, from Petr Machata. 29) Add generic network device failover driver, from Sridhar Samudrala. * ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits) strparser: Add __strp_unpause and use it in ktls. rxrpc: Fix terminal retransmission connection ID to include the channel net: hns3: Optimize PF CMDQ interrupt switching process net: hns3: Fix for VF mailbox receiving unknown message net: hns3: Fix for VF mailbox cannot receiving PF response bnx2x: use the right constant Revert "net: sched: cls: Fix offloading when ingress dev is vxlan" net: dsa: b53: Fix for brcm tag issue in Cygnus SoC enic: fix UDP rss bits netdev-FAQ: clarify DaveM's position for stable backports rtnetlink: validate attributes in do_setlink() mlxsw: Add extack messages for port_{un, }split failures netdevsim: Add extack error message for devlink reload devlink: Add extack to reload and port_{un, }split operations net: metrics: add proper netlink validation ipmr: fix error path when ipmr_new_table fails ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds net: hns3: remove unused hclgevf_cfg_func_mta_filter netfilter: provide udp*_lib_lookup for nf_tproxy qed*: Utilize FW 8.37.2.0 ...

mmc: sd: Define name for default speed dtr

2018-05-29T10:24:26Z

Add a new define for the sd default speed 25MHz case Signed-off-by: Yinbo Zhu Signed-off-by: Ulf Hansson

mmc: core: add tunable delay waiting for power to be stable

2018-05-21T08:38:50Z

The hard-coded 10ms delay in mmc_power_up came from commit 79bccc5aefb4 ("mmc: increase power up delay"), which said "The TI controller on Toshiba Tecra M5 needs more time to power up or the cards will init incorrectly or not at all." But it's too engineering solution for a special board but force all platforms to wait for that long time, especially painful for mmc_power_up for eMMC when booting. However, it's added since 2009, and we can't tell if other platforms benefit from it. But in practise, the modern hardware are most likely to have a stable power supply with 1ms after setting it for no matter PMIC or discrete power. And more importnatly, most regulators implement the callback of ->set_voltage_time_sel() for regulator core to wait for specific period of time for the power supply to be stable, which means once regulator_set_voltage_* return, the power should reach the the minimum voltage that works for initialization. Of course, if there are some other ways for host to power the card, we should allow them to argue a suitable delay as well. With this patch, we could assign the delay from firmware, or we could assigne it via ->set_ios() callback from host drivers. Signed-off-by: Shawn Lin Signed-off-by: Ulf Hansson

brcmfmac: Add support for bcm43364 wireless chipset

2018-05-09T10:24:41Z

Add support for the BCM43364 chipset via an SDIO interface, as used in e.g. the Murata 1FX module. The BCM43364 uses the same firmware as the BCM43430 (which is already included), the only difference is the omission of Bluetooth. However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place triggers the brcmfmac driver to load, and then correctly use the firmware file 'brcmfmac43430-sdio.bin'. Signed-off-by: Sean Lanigan Acked-by: Ulf Hansson Signed-off-by: Kalle Valo

mmc: core: Export a function mmc_sw_reset() to allow soft reset of cards

2018-05-08T07:33:42Z

It's rather common that a firmware is loaded into an SDIO func device memory, by the corresponding SDIO func driver during ->probe() time. However, to actually start running the new firmware, sometimes a soft reset (no power cycle) and a re-initialization of the card is needed. This is for example the case with the Espressif ESP8089 WiFi chips, when connected to an SDIO interface. To cope with this scenario, let's add a new exported function, mmc_sw_reset(), which may be called when a soft reset and re-initialization of the card are needed. The mmc_sw_reset() is implemented on top of a new bus ops callback, similar to how the mmc_hw_reset() has been implemented. Signed-off-by: Ulf Hansson Tested-by: Quentin Schulz Reviewed-by: Shawn Lin

Merge branch 'sdhci_omap' into next

2018-05-03T08:34:06Z

Merge immutable branch for sdhci-omap to add UHS/HS200 mode support. Signed-off-by: Ulf Hansson

mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v

2018-05-03T07:36:19Z

The SDHCI controller in a SoC might support HS200/HS400 (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is modeled such that the IO lines are not connected to 1.8v then HS200/HS400 cannot be supported. Disable HS200/HS400 if the board does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v if the IO lines are not connected to 1.8v. Signed-off-by: Kishon Vijay Abraham I Acked-by: Tony Lindgren Signed-off-by: Ulf Hansson