user/sven/linux.git/include/linux/mtd/cfi.h, branch ipvs/experimental

mtd: move manufacturer to the common cfi.h header file

2009-11-30T09:51:26Z

This patch moves the MANUFACTURER_ST and MANUFACTURER_INTEL to the include/linux/mtd/cfi.h header file and renames them to CFI_MFR_ST and CFI_MFR_INTEL. CFI_MFR_ST was already present there. All references in drivers/mtd/chips/cfi_cmdset_0001.c are updated to reflect this. Signed-off-by: Hans-Christian Egtvedt Acked-by: Nicolas Pitre Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse

[MTD] CFI: remove major/minor version check for command set 0x0002

2009-01-09T12:16:28Z

The NOR Flash memory K8P2815UQB from Samsung uses the major version number '0'. Add a quirk to cope with it. Signed-off-by: Wolfgang Grandegger Signed-off-by: David Woodhouse

[MTD] [NOR] Fix cfi_send_gen_cmd handling of x16 devices in x8 mode (v4)

2008-11-05T13:40:25Z

For "unlock" cycles to 16bit devices in 8bit compatibility mode we need to use the byte addresses 0xaaa and 0x555. These effectively match the word address 0x555 and 0x2aa, except the latter has its low bit set. Most chips don't care about the value of the 'A-1' pin in x8 mode, but some -- like the ST M29W320D -- do. So we need to be careful to set it where appropriate. cfi_send_gen_cmd is only ever passed addresses where the low byte is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are affected by this patch, by masking in the extra low bit when the device is known to be in compatibility mode. [dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa] v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile I'm writing this patch way to late at night. v3: Bring all of the work back into cfi_build_cmd_addr including calling of map_bankwidth(map) and cfi_interleave(cfi) So every caller doesn't need to. v2: Only modified the address if we our device_type is larger than our bus width. Cc: stable@kernel.org Signed-off-by: Eric W. Biederman Signed-off-by: David Woodhouse

[MTD] [NOR] Rename and export new cfi_qry_*() functions

2008-08-07T10:55:07Z

They need to be exported, so let's give them less generic-sounding names while we're at it. Original export patch, along with the suggestion about the nomenclature, from Stephen Rothwell. Signed-off-by: David Woodhouse

[MTD] [NOR] Add qry_mode_on()/qry_omde_off() to deal with odd chips

2008-08-06T08:43:58Z

There are some CFI chips which require non standard procedures to get into QRY mode. The possible way to support them would be trying different modes till QRY will be read. This patch introduce two new functions qry_mode_on qry_mode_off. qry_mode_on tries different commands in order switch chip into QRY mode. So if we have one more "odd" chip - we just could add several lines to qry_mode_on. Also using these functions remove unnecessary code duplicaton in porbe procedure. Currently there are two "odd" cases 1. Some old intel chips which require 0xFF before 0x98 2. ST M29DW chip which requires 0x98 to be sent at 0x555 (according to CFI should be 0x55) This patch is partialy based on the patch from Uwe (see "[PATCH 2/4] [RFC][MTD] cfi_probe: remove Intel chip workaround" thread ) Signed-off-by: Alexey Korolev Signed-off-by: Alexander Belyakov Signed-off-by: David Woodhouse

MTD/JFFS2: remove CVS keywords

2008-06-04T16:50:17Z

Once upon a time, the MTD repository was using CVS. This patch therefore removes all usages of the no longer updated CVS keywords from the MTD code. This also includes code that printed them to the user. Signed-off-by: Adrian Bunk Signed-off-by: David Woodhouse

[MTD] [NOR] Fix incorrect interface code for x16/x32 chips

2008-01-10T22:07:12Z

According to "Common Flash Memory Interface Publication 100" dated December 1, 2001, the interface code for x16/x32 chips is 0x0005, and not 0x0004 used so far. Signed-off-by: Bartlomiej Sieka Signed-off-by: David Woodhouse

[MTD] Fix CFI build error when no map width or interleave supported

2007-09-06T08:40:21Z

When building NOR flash support, you have compile-time options for the bus width and the number of individual chips which are interleaved together onto that bus. The code to deal with arbitrary geometry is a bit convoluted, and people want to just configure it for the specific hardware they have, to avoid the runtime overhead. Selecting _none_ of the available options doesn't make any sense. You should have at least one. This makes it build though, since people persist in trying. Signed-off-by: David Woodhouse

MTD: Convert Atmel PRI information to AMD format

2006-08-17T01:13:06Z

Atmel flash chips don't have PRI information in the same format as AMD flash chips. This patch installs a fixup for all Atmel chips that converts the relevant PRI fields into AMD format. Only the fields that are actually used by the command set is actually converted. The rest are initialized to zero (which should be safe) Signed-off-by: Haavard Skinnemoen Signed-off-by: Josh Boyer

Don't include linux/config.h from anywhere else in include/

2006-04-26T11:56:16Z

Signed-off-by: David Woodhouse