user/sven/linux.git/include/linux/netdevice.h, branch v3.9

net: count hw_addr syncs so that unsync works properly.

2013-04-05T04:18:46Z

A few drivers use dev_uc_sync/unsync to synchronize the address lists from master down to slave/lower devices. In some cases (bond/team) a single address list is synched down to multiple devices. At the time of unsync, we have a leak in these lower devices, because "synced" is treated as a boolean and the address will not be unsynced for anything after the first device/call. Treat "synced" as a count (same as refcount) and allow all unsync calls to work. Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller

line up comment for ndo_bridge_getlink

2013-03-27T18:06:41Z

Signed-off-by: Dmitry Kravkov Signed-off-by: David S. Miller

net: fix a build failure when !CONFIG_PROC_FS

2013-02-19T18:18:13Z

When !CONFIG_PROC_FS dev_mcast_init() is not defined, actually we can just merge dev_mcast_init() into dev_proc_init(). Reported-by: Gao feng Cc: Gao feng Cc: "David S. Miller" Signed-off-by: Cong Wang Signed-off-by: David S. Miller

net: move procfs code to net/core/net-procfs.c

2013-02-19T05:51:10Z

Similar to net/core/net-sysfs.c, group procfs code to a single unit. Cc: "David S. Miller" Signed-off-by: Cong Wang Signed-off-by: David S. Miller

net: factor out skb_mac_gso_segment() from skb_gso_segment()

2013-02-15T20:16:03Z

This function will be used in next GRE_GSO patch. This patch does not change any functionality. It only exports skb_mac_gso_segment() function. [ Use skb_reset_mac_len() -DaveM ] Signed-off-by: Pravin B Shelar Acked-by: Eric Dumazet Signed-off-by: David S. Miller

bridge: Add vlan support to static neighbors

2013-02-14T00:42:16Z

When a user adds bridge neighbors, allow him to specify VLAN id. If the VLAN id is not specified, the neighbor will be added for VLANs currently in the ports filter list. If no VLANs are configured on the port, we use vlan 0 and only add 1 entry. Signed-off-by: Vlad Yasevich Acked-by: Jitendra Kalsaria Signed-off-by: David S. Miller

bridge: Dump vlan information from a bridge port

2013-02-14T00:41:46Z

Using the RTM_GETLINK dump the vlan filter list of a given bridge port. The information depends on setting the filter flag similar to how nic VF info is dumped. Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller

bridge: Add netlink interface to configure vlans on bridge ports

2013-02-14T00:41:46Z

Add a netlink interface to add and remove vlan configuration on bridge port. The interface uses the RTM_SETLINK message and encodes the vlan configuration inside the IFLA_AF_SPEC. It is possble to include multiple vlans to either add or remove in a single message. Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller

net/802: Implement Multiple Registration Protocol (MRP)

2013-02-11T01:37:22Z

Initial implementation of the Multiple Registration Protocol (MRP) from IEEE 802.1Q-2011, based on the existing implementation of the Generic Attribute Registration Protocol (GARP). Signed-off-by: David Ward Acked-by: Patrick McHardy Signed-off-by: David S. Miller

net: adjust skb_gso_segment() for calling in rx path

2013-02-06T20:58:00Z

skb_gso_segment() is almost always called in tx path, except for openvswitch. It calls this function when it receives the packet and tries to queue it to user-space. In this special case, the ->ip_summed check inside skb_gso_segment() is no longer true, as ->ip_summed value has different meanings on rx path. This patch adjusts skb_gso_segment() so that we can at least avoid such warnings on checksum. Cc: Jesse Gross Cc: David S. Miller Signed-off-by: Cong Wang Signed-off-by: David S. Miller