user/sven/linux.git/include/linux/pci.h, branch v3.0.50

PCI: EHCI: fix crash during suspend on ASUS computers

2012-07-16T15:47:50Z

commit dbf0e4c7257f8d684ec1a3c919853464293de66e upstream. Quite a few ASUS computers experience a nasty problem, related to the EHCI controllers, when going into system suspend. It was observed that the problem didn't occur if the controllers were not put into the D3 power state before starting the suspend, and commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during suspend on ASUS computers) was created to do this. It turned out this approach messed up other computers that didn't have the problem -- it prevented USB wakeup from working. Consequently commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b (USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2) was merged; it reverted the earlier commit and added a whitelist of known good board names. Now we know the actual cause of the problem. Thanks to AceLan Kao for tracking it down. According to him, an engineer at ASUS explained that some of their BIOSes contain a bug that was added in an attempt to work around a problem in early versions of Windows. When the computer goes into S3 suspend, the BIOS tries to verify that the EHCI controllers were first quiesced by the OS. Nothing's wrong with this, but the BIOS does it by checking that the PCI COMMAND registers contain 0 without checking the controllers' power state. If the register isn't 0, the BIOS assumes the controller needs to be quiesced and tries to do so. This involves making various MMIO accesses to the controller, which don't work very well if the controller is already in D3. The end result is a system hang or memory corruption. Since the value in the PCI COMMAND register doesn't matter once the controller has been suspended, and since the value will be restored anyway when the controller is resumed, we can work around the BIOS bug simply by setting the register to 0 during system suspend. This patch (as1590) does so and also reverts the second commit mentioned above, which is now unnecessary. In theory we could do this for every PCI device. However to avoid introducing new problems, the patch restricts itself to EHCI host controllers. Finally the affected systems can suspend with USB wakeup working properly. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632 Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728 Based-on-patch-by: AceLan Kao Signed-off-by: Alan Stern Tested-by: Dâniel Fraga Tested-by: Javier Marcet Tested-by: Andrey Rahmatullin Tested-by: Oleksij Rempel Tested-by: Pavel Pisa Acked-by: Bjorn Helgaas Acked-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2

2012-06-22T18:34:15Z

commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b upstream. This patch (as1558) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. A similar patch has already been applied as commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during suspend on ASUS computers). The patch supersedes that one and reverts it. There are two differences: The old patch added the flag at the USB level; this patch adds it at the PCI level. The old patch applied to all chipsets with the same vendor, subsystem vendor, and product IDs; this patch makes an exception for a known-good system (based on DMI information). Signed-off-by: Alan Stern Tested-by: Dâniel Fraga Tested-by: Andrey Rahmatullin Tested-by: Steven Rostedt Reviewed-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

Merge branch 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6

2011-05-24T19:06:40Z

* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits) drivers/gpu/drm/radeon/atom.c: fix warning drm/radeon/kms: bump kms version number drm/radeon/kms: properly set num banks for fusion asics drm/radeon/kms/atom: move dig phy init out of modesetting drm/radeon/kms/cayman: fix typo in register mask drm/radeon/kms: fix typo in spread spectrum code drm/radeon/kms: fix tile_config value reported to userspace on cayman. drm/radeon/kms: fix incorrect comparison in cayman setup code. drm/radeon/kms: add wait idle ioctl for eg->cayman drm/radeon/cayman: setup hdp to invalidate and flush when asked drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked agp/uninorth: Fix lockups with radeon KMS and >1x. drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices drm/radeon/kms: fixup eDP connector handling drm/radeon/kms: bail early for eDP in hotplug callback drm/radeon/kms: simplify hotplug handler logic drm/radeon/kms: rewrite DP handling drm/radeon/kms/atom: add support for setting DP panel mode drm/radeon/kms: atombios.h updates for DP panel mode ...

PCI: Add interfaces to store and load the device saved state

2011-05-21T19:17:09Z

For KVM device assignment, we'd like to save off the state of a device prior to passing it to the guest and restore it later. We also want to allow pci_reset_funciton() to be called while the device is owned by the guest. This however overwrites and invalidates the struct pci_dev buffers, so we can't just manually call save and restore. Add generic interfaces for the saved state to be stored and reloaded back into struct pci_dev at a later time. Signed-off-by: Alex Williamson Signed-off-by: Jesse Barnes

PCI: Track the size of each saved capability data area

2011-05-21T19:17:08Z

This will allow us to store and load it later. Signed-off-by: Alex Williamson Signed-off-by: Jesse Barnes

PCI: add latency tolerance reporting enable/disable support

2011-05-11T22:18:53Z

Latency tolerance reporting allows devices to send messages to the root complex indicating their latency tolerance for snooped & unsnooped memory transactions. Add support for enabling & disabling this feature, along with a routine to set the max latencies a device should send upstream. Signed-off-by: Jesse Barnes

PCI: add OBFF enable/disable support

2011-05-11T22:18:48Z

OBFF (optimized buffer flush/fill), where supported, can help improve energy efficiency by giving devices information about when interrupts and other activity will have a reduced power impact. It requires support from both the device and system (i.e. not only does the device need to respond to OBFF messages, but the platform must be capable of generating and routing them to the end point). Signed-off-by: Jesse Barnes

PCI: add ID-based ordering enable/disable support

2011-05-11T22:18:40Z

Add support to allow drivers to enable/disable ID-based ordering. Where supported, ID-based ordering can significantly improve the latency of individual requests by preventing them from queueing up behind unrelated traffic. Signed-off-by: Jesse Barnes

vgaarb: use bridges to control VGA routing where possible.

2011-05-04T03:38:46Z

So in a lot of modern systems, a GPU will always be below a parent bridge that won't share with any other GPUs. This means VGA arbitration on those GPUs can be controlled by using the bridge routing instead of io/mem decodes. The problem is locating which GPUs share which upstream bridges. This patch attempts to identify all the GPUs which can be controlled via bridges, and ones that can't. This patch endeavours to work out the bridge sharing semantics. When disabling GPUs via a bridge, it doesn't do irq callbacks or touch the io/mem decodes for the gpu. Signed-off-by: Dave Airlie

PCI/ACPI: Report ASPM support to BIOS if not disabled from command line

2011-03-21T16:38:02Z

We need to distinguish the situation in which ASPM support is disabled from the command line or through .config from the situation in which it is disabled, because the hardware or BIOS can't handle it. In the former case we should not report ASPM support to the BIOS through ACPI _OSC, but in the latter case we should do that. Introduce pcie_aspm_support_enabled() that can be used by acpi_pci_root_add() to determine whether or not it should report ASPM support to the BIOS through _OSC. Cc: stable@kernel.org References: https://bugzilla.kernel.org/show_bug.cgi?id=29722 References: https://bugzilla.kernel.org/show_bug.cgi?id=20232 Reported-and-tested-by: Ortwin Glück Reviewed-by: Kenji Kaneshige Tested-by: Kenji Kaneshige Signed-off-by: Rafael J. Wysocki Signed-off-by: Jesse Barnes