user/sven/linux.git/include/linux/regulator/consumer.h, branch v3.2.19

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

2011-10-28T21:25:01Z

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits) ALSA: hda - Fix ADC input-amp handling for Cx20549 codec ALSA: hda - Keep EAPD turned on for old Conexant chips ALSA: hda/realtek - Fix missing volume controls with ALC260 ASoC: wm8940: Properly set codec->dapm.bias_level ALSA: hda - Fix pin-config for ASUS W90V ALSA: hda - Fix surround/CLFE headphone and speaker pins order ALSA: hda - Fix typo ALSA: Update the sound git tree URL ALSA: HDA: Add new revision for ALC662 ASoC: max98095: Convert codec->hw_write to snd_soc_write ASoC: keep pointer to resource so it can be freed ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2 ASoC: da7210: Add support for line out and DAC ASoC: da7210: Add support for DAPM ALSA: hda/realtek - Fix DAC assignments of multiple speakers ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value ASoC: Set sgtl5000->ldo in ldo_regulator_register ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture ...

regulator: Implement deferred disable support

2011-09-14T09:58:23Z

It is a reasonably common pattern for hardware to require some delay after being quiesced before the disable has finalised, especially in mixed signal devices. For example, an active discharge may be required to ensure that the circuit starts up again in a known state. Avoid having to implement such delays in the regulator API by providing regulator_deferred_disable() which will do a regulator_disable() a specified number of milliseconds after it is called. Due to the reference counting done on regulators a deferred disable can be cancelled by doing another regulator_enable(). Signed-off-by: Mark Brown Acked-by: Liam Girdwood

regulator: fix kernel-doc warning in consumer.h

2011-09-08T21:43:03Z

Fix kernel-doc warning about internal/private data by marking it as "private:" so that kernel-doc will ignore it. Warning(include/linux/regulator/consumer.h:128): No description found for parameter 'ret' Signed-off-by: Randy Dunlap Acked-by: Mark Brown Signed-off-by: Linus Torvalds

regulator: Do bulk enables of regulators in parallel

2011-05-30T10:56:57Z

In order to reduce the impact of ramp times rather than enabling the regulators for a device in series use async tasks to run the actual enables. This means that the delays which the enables implement can all run in parallel, though it does mean that the order in which the supplies come on may be unstable. For super bonus fun points if any of the regulators are shared between multiple supplies on the same device (as is rather likely) then this will test our locking. Note that in this case we only delay once for each physical regulator so the threads shouldn't block each other while delaying. It'd be even nicer if we could coalesce writes to a shared enable registers in PMICs but that's definitely future work, and it may also be useful and is certainly more achievable to optimise out the parallelism if none of the regulators implement ramp delays. Signed-off-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: provide consumer interface for fall/rise time

2011-03-26T14:15:06Z

This exposes the functionality for rise/fall fime when setting voltage to the consumers. Cc: Bengt Jonsson Signed-off-by: Linus Walleij Acked-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: Add API to re-apply voltage to hardware

2011-01-12T14:33:05Z

When cooperating with an external control source the regulator setup may be changed underneath the API. Currently consumers can just redo the regulator_set_voltage() to restore a previously set configuration but provide an explicit API for doing this as optimsations in the regulator_set_voltage() implementation will shortly prevent that. Signed-off-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: Let drivers know when they use the stub API

2010-04-19T12:17:10Z

Have the stub variant of regulator_get() return NULL, so that drivers can (but still don't have to) handle this case specifically. Signed-off-by: Jean Delvare Cc: Mark Brown Cc: Jerome Oufella Acked-by: Mark Brown Signed-off-by: Liam Girdwood

regulator: Add notifier event on regulator disable

2010-03-03T14:49:23Z

The intended use case is for drivers which disable regulators to save power but need to do some work to restore the hardware state when restarting. If the supplies are not actually disabled due to board limits or sharing with other active devices this notifier allows the driver to avoid unneeded reinitialisation, particularly when used with runtime PM. Signed-off-by: Mark Brown

regulator: consumer.h - fix build when consumer.h is #included first.

2009-12-17T10:27:27Z

consumer.h requires device.h for stand alone build. Signed-off-by: Liam Girdwood

regulator: Add regulator voltage range check API

2009-09-22T12:32:38Z

Simplify checking of support for voltage ranges by providing an API which wraps the existing count and list operations. Signed-off-by: Mark Brown Signed-off-by: Liam Girdwood