user/sven/linux.git/include/linux/serial_core.h, branch v6.1.4

serial: Deassert Transmit Enable on probe in driver-specific way

2022-09-25T07:28:57Z

When a UART port is newly registered, uart_configure_port() seeks to deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl. However a number of UART drivers interpret a set RTS bit as *assertion* instead of deassertion: Affected drivers include those using serial8250_em485_config() (except 8250_bcm2835aux.c) and some using mctrl_gpio (e.g. imx.c). Since the interpretation of the RTS bit is driver-specific, it is not suitable as a means to centrally deassert Transmit Enable in the serial core. Instead, the serial core must call on drivers to deassert it in their driver-specific way. One way to achieve that is to call ->rs485_config(). It implicitly deasserts Transmit Enable. So amend uart_configure_port() and uart_resume_port() to invoke uart_rs485_config(). That allows removing calls to uart_rs485_config() from drivers' ->probe() hooks and declaring the function static. Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no hardware flow control, so the modem control lines are irrelevant and need not be touched. When leaving RS485 mode, reset the modem control lines to the state stored in port->mctrl. That way, UARTs which are muxed between RS485 and RS232 transceivers drive the lines correctly when switched to RS232. (serial8250_do_startup() historically raises the OUT1 modem signal because otherwise interrupts are not signaled on ancient PC UARTs, but I believe that no longer applies to modern, RS485-capable UARTs and is thus safe to be skipped.) imx.c modifies port->mctrl whenever Transmit Enable is asserted and deasserted. Stop it from doing that so port->mctrl reflects the RS232 line state. 8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling ->set_mctrl(). Because that is now a no-op in RS485 mode, amend the function to call serial8250_em485_stop_tx(). fsl_lpuart.c retrieves and applies the RS485 device tree properties after registering the UART port. Because applying now happens on registration in uart_configure_port(), move retrieval of the properties ahead of uart_add_one_port(). Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/ Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/ Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Matthias Schiffer Reported-by: Roosen Henri Tested-by: Matthias Schiffer Reviewed-by: Ilpo Järvinen Signed-off-by: Lukas Wunner Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

Merge 7e2cd21e02b3 ("Merge tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next

2022-09-25T07:22:13Z

We need the tty fixes and api additions in this branch. Signed-off-by: Greg Kroah-Hartman

serial: 8250: Switch UART port flags to using BIT_ULL

2022-09-22T14:28:47Z

Use BIT_ULL rather than encoding bits explicitly where applicable with UART port flags. This makes a (__force upf_t) cast redundant, but keep it for visual consistency with the flags defined in terms of userspace macros. Signed-off-by: Maciej W. Rozycki Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209210007030.41633@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman

serial: 8250: Let drivers request full 16550A feature probing

2022-09-22T14:28:47Z

A SERIAL_8250_16550A_VARIANTS configuration option has been recently defined that lets one request the 8250 driver not to probe for 16550A device features so as to reduce the driver's device startup time in virtual machines. Some actual hardware devices require these features to have been fully determined however for their driver to work correctly, so define a flag to let drivers request full 16550A feature probing on a device-by-device basis if required regardless of the SERIAL_8250_16550A_VARIANTS option setting chosen. Fixes: dc56ecb81a0a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants") Cc: stable@vger.kernel.org # v5.6+ Reported-by: Anders Blomdell Signed-off-by: Maciej W. Rozycki Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209202357520.41633@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman

serial: Create uart_xmit_advance()

2022-09-07T14:40:16Z

A very common pattern in the drivers is to advance xmit tail index and do bookkeeping of Tx'ed characters. Create uart_xmit_advance() to handle it. Reviewed-by: Andy Shevchenko Cc: stable Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20220901143934.8850-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman

Merge 6.0-rc4 into tty-next

2022-09-05T05:59:28Z

We need the tty/serial fixes in here as well. Signed-off-by: Greg Kroah-Hartman

serial: Make ->set_termios() old ktermios const

2022-08-30T12:22:35Z

There should be no reason to adjust old ktermios which is going to get discarded anyway. Reviewed-by: Andy Shevchenko Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman

serial: document start_rx member at struct uart_ops

2022-08-18T14:40:31Z

Fix this doc build warning: ./include/linux/serial_core.h:397: warning: Function parameter or member 'start_rx' not described in 'uart_ops' Signed-off-by: Mauro Carvalho Chehab Link: https://lore.kernel.org/r/5d07ae2eec8fbad87e623160f9926b178bef2744.1660829433.git.mchehab@kernel.org Signed-off-by: Greg Kroah-Hartman

Merge tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2022-08-08T18:31:40Z

Pull tty / serial driver updates from Greg KH: "Here is the big set of tty and serial driver changes for 6.0-rc1. It was delayed from last week as I wanted to make sure the last commit here got some good testing in linux-next and elsewhere as it seemed to show up only late in testing for some reason. Nothing major here, just lots of cleanups from Jiri and Ilpo to make the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo). Also included in here is the obligatory n_gsm updates from Daniel Starke and lots of tiny driver updates and minor fixes and tweaks for other smaller serial drivers. All of these have been in linux-next for a while with no reported problems" * tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits) tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements tty: amiserial: Fix comment typo tty: serial: document uart_get_console() tty: serial: serial_core, reformat kernel-doc for functions Documentation: serial: link uart_ops properly Documentation: serial: move GPIO kernel-doc to the functions Documentation: serial: dedup kernel-doc for uart functions Documentation: serial: move uart_ops documentation to the struct dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126 serial: mvebu-uart: uart2 error bits clearing tty: serial: fsl_lpuart: correct the count of break characters serial: stm32: make info structs static to avoid sparse warnings serial: fsl_lpuart: zero out parity bit in CS7 mode tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate. serial: 8250_bcm2835aux: Add missing clk_disable_unprepare() tty: vt: initialize unicode screen buffer serial: remove VR41XX serial driver serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags serial: 8250_dwlib: remove redundant sanity check for RS485 flags dt_bindings: rs485: Correct delay values ...

Documentation: serial: move uart_ops documentation to the struct

2022-07-28T08:37:42Z

While it's a lot of text, it always helps to keep it up to date when it's by the source. (And not in a separate file.) The documentation tooling also makes sure that all members of the structure are documented. (If not, it complains loudly.) Finally, there needs to be no comments inlined in the structure, so they are dropped as they are superfluous now. The compilation time of this header (tested with serial_core.c) didn't change in my testing at all. Signed-off-by: Jiri Slaby Link: https://lore.kernel.org/r/20220728061056.20799-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman