user/sven/linux.git/include/linux/tpm.h, branch v6.4.5

tpm: Prevent hwrng from activating during resume

2023-05-15T23:43:12Z

Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero bytes. This prevents hwrng from racing during resume. Cc: stable@vger.kernel.org Fixes: 6e592a065d51 ("tpm: Move Linux RNG connection to hwrng") Reviewed-by: Jerry Snitselaar Signed-off-by: Jarkko Sakkinen

tpm: Re-enable TPM chip boostrapping non-tpm_tis TPM drivers

2023-04-28T13:06:36Z

TPM chip bootstrapping was removed from tpm_chip_register(), and it was relocated to tpm_tis_core. This breaks all drivers which are not based on tpm_tis because the chip will not get properly initialized. Take the corrective steps: 1. Rename tpm_chip_startup() as tpm_chip_bootstrap() and make it one-shot. 2. Call tpm_chip_bootstrap() in tpm_chip_register(), which reverts the things as tehy used to be. Cc: Lino Sanfilippo Fixes: 548eb516ec0f ("tpm, tpm_tis: startup chip before testing for interrupts") Reported-by: Pengfei Xu Link: https://lore.kernel.org/all/ZEjqhwHWBnxcaRV5@xpf.sh.intel.com/ Tested-by: Pengfei Xu Signed-off-by: Jarkko Sakkinen

tpm: add vendor flag to command code validation

2023-02-13T08:11:20Z

Some TPM 2.0 devices have support for additional commands which are not part of the TPM 2.0 specifications. These commands are identified with bit 29 of the 32 bits command codes. Contrarily to other fields of the TPMA_CC spec structure used to list available commands, the Vendor flag also has to be present in the command code itself (TPM_CC) when called. Add this flag to tpm_find_cc() mask to prevent blocking vendor command codes that can actually be supported by the underlying TPM device. Signed-off-by: Julien Gomes Tested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: Add Upgrade/Reduced mode support for TPM2 modules

2022-01-08T22:18:47Z

If something went wrong during the TPM firmware upgrade, like power failure or the firmware image file get corrupted, the TPM might end up in Upgrade or Failure mode upon the next start. The state is persistent between the TPM power cycle/restart. According to TPM specification: * If the TPM is in Upgrade mode, it will answer with TPM2_RC_UPGRADE to all commands except TPM2_FieldUpgradeData(). It may also accept other commands if it is able to complete them using the previously installed firmware. * If the TPM is in Failure mode, it will allow performing TPM initialization but will not provide any crypto operations. Will happily respond to Field Upgrade calls. Change the behavior of the tpm2_auto_startup(), so it detects the active running mode of the TPM by adding the following checks. If tpm2_do_selftest() call returns TPM2_RC_UPGRADE, the TPM is in Upgrade mode. If the TPM is in Failure mode, it will successfully respond to both tpm2_do_selftest() and tpm2_startup() calls. Although, will fail to answer to tpm2_get_cc_attrs_tbl(). Use this fact to conclude that TPM is in Failure mode. If detected that the TPM is in the Upgrade or Failure mode, the function sets TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag. The TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag is used later during driver initialization/deinitialization to disable functionality which makes no sense or will fail in the current TPM state. Following functionality is affected: * Do not register TPM as a hwrng * Do not register sysfs entries which provide information impossible to obtain in limited mode * Do not register resource managed character device Signed-off-by: axelj Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: fix Atmel TPM crash caused by too frequent queries

2021-10-26T02:03:34Z

The Atmel TPM 1.2 chips crash with error `tpm_try_transmit: send(): error -62` since kernel 4.14. It is observed from the kernel log after running `tpm_sealdata -z`. The error thrown from the command is as follows ``` $ tpm_sealdata -z Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl, code=0087 (135), I/O error ``` The issue was reproduced with the following Atmel TPM chip: ``` $ tpm_version T0 TPM 1.2 Version Info: Chip Version: 1.2.66.1 Spec Level: 2 Errata Revision: 3 TPM Vendor ID: ATML TPM Version: 01010000 Manufacturer Info: 41544d4c ``` The root cause of the issue is due to the TPM calls to msleep() were replaced with usleep_range() [1], which reduces the actual timeout. Via experiments, it is observed that the original msleep(5) actually sleeps for 15ms. Because of a known timeout issue in Atmel TPM 1.2 chip, the shorter timeout than 15ms can cause the error described above. A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further reduced the timeout to less than 1ms. With experiments, the problematic timeout in the latest kernel is the one for `wait_for_tpm_stat`. To fix it, the patch reverts the timeout of `wait_for_tpm_stat` to 15ms for all Atmel TPM 1.2 chips, but leave it untouched for Ateml TPM 2.0 chip, and chips from other vendors. As explained above, the chosen 15ms timeout is the actual timeout before this issue introduced, thus the old value is used here. Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to the existing TPM_TIMEOUT_RANGE_US (300us). The fixed has been tested in the system with the affected Atmel chip with no issues observed after boot up. References: [1] 9f3fc7bcddcb tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers [2] cf151a9a44d5 tpm: reduce tpm polling delay in tpm_tis_core [3] 59f5a6b07f64 tpm: reduce poll sleep time in tpm_transmit() [4] 424eaf910c32 tpm: reduce polling time to usecs for even finer granularity Fixes: 9f3fc7bcddcb ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers") Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/ Signed-off-by: Hao Wu Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

security: keys: trusted: Make sealed key properly interoperable

2021-04-14T13:30:30Z

The current implementation appends a migratable flag to the end of a key, meaning the format isn't exactly interoperable because the using party needs to know to strip this extra byte. However, all other consumers of TPM sealed blobs expect the unseal to return exactly the key. Since TPM2 keys have a key property flag that corresponds to migratable, use that flag instead and make the actual key the only sealed quantity. This is secure because the key properties are bound to a hash in the private part, so if they're altered the key won't load. Backwards compatibility is implemented by detecting whether we're loading a new format key or not and correctly setting migratable from the last byte of old format keys. Signed-off-by: James Bottomley Reviewed-by: Jarkko Sakkinen Tested-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

KEYS: trusted: Reserve TPM for seal and unseal operations

2021-02-16T08:40:28Z

When TPM 2.0 trusted keys code was moved to the trusted keys subsystem, the operations were unwrapped from tpm_try_get_ops() and tpm_put_ops(), which are used to take temporarily the ownership of the TPM chip. The ownership is only taken inside tpm_send(), but this is not sufficient, as in the key load TPM2_CC_LOAD, TPM2_CC_UNSEAL and TPM2_FLUSH_CONTEXT need to be done as a one single atom. Take the TPM chip ownership before sending anything with tpm_try_get_ops() and tpm_put_ops(), and use tpm_transmit_cmd() to send TPM commands instead of tpm_send(), reverting back to the old behaviour. Fixes: 2e19e10131a0 ("KEYS: trusted: Move TPM2 trusted keys code") Reported-by: "James E.J. Bottomley" Cc: stable@vger.kernel.org Cc: David Howells Cc: Mimi Zohar Cc: Sumit Garg Acked-by Sumit Garg Tested-by: Mimi Zohar Signed-off-by: Jarkko Sakkinen

tpm: add sysfs exports for all banks of PCR registers

2021-02-16T08:40:27Z

Create sysfs per hash groups with 24 PCR files in them one group, named pcr-, for each agile hash of the TPM. The files are plugged in to a PCR read function which is TPM version agnostic, so this works also for TPM 1.2 but the hash is only sha1 in that case. Note: the macros used to create the hashes emit spurious checkpatch warnings. Do not try to "fix" them as checkpatch recommends, otherwise they'll break. Signed-off-by: James Bottomley Reviewed-by: Jerry Snitselaar Tested-by: Thiago Jung Bauermann Tested-by: Jarkko Sakkinen Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen

tpm: Unify the mismatching TPM space buffer sizes

2020-07-24T06:26:23Z

The size of the buffers for storing context's and sessions can vary from arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be enough for most use with three handles (that is how many we allow at the moment). Parametrize the buffer size while doing this, so that it is easier to revisit this later on if required. Cc: stable@vger.kernel.org Reported-by: Stefan Berger Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Reviewed-by: Jerry Snitselaar Tested-by: Stefan Berger Signed-off-by: Jarkko Sakkinen

security: keys: trusted: fix lost handle flush

2019-12-17T09:46:43Z

The original code, before it was moved into security/keys/trusted-keys had a flush after the blob unseal. Without that flush, the volatile handles increase in the TPM until it becomes unusable and the system either has to be rebooted or the TPM volatile area manually flushed. Fix by adding back the lost flush, which we now have to export because of the relocation of the trusted key code may cause the consumer to be modular. Signed-off-by: James Bottomley Fixes: 2e19e10131a0 ("KEYS: trusted: Move TPM2 trusted keys code") Reviewed-by: Jerry Snitselaar Reviewed-by: Jarkko Sakkinen Signed-off-by: Jarkko Sakkinen