user/sven/linux.git/include/linux/usb/hcd.h, branch v3.18.22

USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)

2015-03-06T22:53:00Z

commit 074f9dd55f9cab1b82690ed7e44bcf38b9616ce0 upstream. Currently the USB stack assumes that all host controller drivers are capable of receiving wakeup requests from downstream devices. However, this isn't true for the isp1760-hcd driver, which means that it isn't safe to do a runtime suspend of any device attached to a root-hub port if the device requires wakeup. This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure and sets the flag in isp1760-hcd. The core is modified to prevent a direct child of the root hub from being put into runtime suspend with wakeup enabled if the flag is set. Signed-off-by: Alan Stern Tested-by: Nicolas Pitre Signed-off-by: Greg Kroah-Hartman Signed-off-by: Greg Kroah-Hartman

usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN

2015-03-06T22:53:00Z

commit 5efd2ea8c9f4f12916ffc8ba636792ce052f6911 upstream. the following error pops up during "testusb -a -t 10" | musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma) hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in hcd_buffer_alloc() returning memory which is 32 bytes aligned and it might by identified by buffer_offset() as another buffer. This means the buffer which is on a 32 byte boundary will not get freed, instead it tries to free another buffer with the error message. This patch fixes the issue by creating the smallest DMA buffer with the size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is smaller). This might be 32, 64 or even 128 bytes. The next three pools will have the size 128, 512 and 2048. In case the smallest pool is 128 bytes then we have only three pools instead of four (and zero the first entry in the array). The last pool size is always 2048 bytes which is the assumed PAGE_SIZE / 2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where we would end up with 8KiB buffer in case we have 16KiB pages. Instead I think it makes sense to have a common size(s) and extend them if there is need to. There is a BUILD_BUG_ON() now in case someone has a minalign of more than 128 bytes. Signed-off-by: Sebastian Andrzej Siewior Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

usb: hcd: add generic PHY support

2014-09-29T15:54:02Z

Add the generic PHY support, analogous to the USB PHY support. Intended it to be used with the PCI EHCI/OHCI drivers and the xHCI platform driver. Signed-off-by: Sergei Shtylyov Signed-off-by: Yoshihiro Shimoda Signed-off-by: Greg Kroah-Hartman

usb: rename phy to usb_phy in HCD

2014-09-29T15:52:59Z

The USB PHY member of the HCD structure is renamed to 'usb_phy' and modifications are done in all drivers accessing it. This is in preparation to adding the generic PHY support. Signed-off-by: Antoine Tenart [Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects, updated changelog.] Signed-off-by: Sergei Shtylyov Acked-by: Alan Stern Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

usb: hcd: add TPL support flag

2014-09-24T04:28:41Z

The targeted hosts (non-PC hosts) need to have TPL (Targeted Peripheral List) for USB OTG & EH certification and other vendor specific requirements. The platform who needs TPL feature should set this flag at usb host controller driver. Signed-off-by: Peter Chen Signed-off-by: Greg Kroah-Hartman

storage: accept some UAS devices if streams are unavailable

2014-03-04T23:41:09Z

On some older XHCIs streams are not supported and the UAS driver will fail at probe time. For those devices storage should try to bind to UAS devices. This patch adds a flag for stream support to HCDs and evaluates it. [Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root hub would get marked as being able to support streams.] Signed-off-by: Oliver Neukum Signed-off-by: Sarah Sharp Acked-by: Hans de Goede

usb: xhci: change enumeration scheme to 'new scheme' by default

2013-12-10T21:54:37Z

Change the default enumeration scheme for xhci attached non-SuperSpeed devices from: Reset SetAddress [xhci address-device BSR = 0] GetDescriptor(8) GetDescriptor(18) ...to: Reset [xhci address-device BSR = 1] GetDescriptor(64) Reset SetAddress [xhci address-device BSR = 0] GetDescriptor(18) ...as some devices misbehave when encountering a SetAddress command prior to GetDescriptor. There are known legacy devices that require this scheme, but testing has found at least one USB3 device that fails enumeration when presented with this ordering. For now, follow the ehci case and enable 'new scheme' by default for non-SuperSpeed devices. To support this enumeration scheme on xhci the AddressDevice operation needs to be performed twice. The first instance of the command enables the HC's device and slot context info for the device, but omits sending the device a SetAddress command (BSR == block set address request). Then, after GetDescriptor completes, follow up with the full AddressDevice+SetAddress operation. As mentioned before, this ordering of events with USB3 devices causes an extra state transition to be exposed to xhci. Previously USB3 devices would transition directly from 'enabled' to 'addressed' and never need to underrun responses to 'get descriptor'. We do see the 64-byte descriptor fetch the correct data, but the following 18-byte descriptor read after the reset gets: bLength = 0 bDescriptorType = 0 bcdUSB = 0 bDeviceClass = 0 bDeviceSubClass = 0 bDeviceProtocol = 0 bMaxPacketSize0 = 9 instead of: bLength = 12 bDescriptorType = 1 bcdUSB = 300 bDeviceClass = 0 bDeviceSubClass = 0 bDeviceProtocol = 0 bMaxPacketSize0 = 9 which results in the discovery process looping until falling back to 'old scheme' enumeration. Acked-by: Alan Stern Reported-by: David Moore Suggested-by: Sarah Sharp Reported-by: Dan Carpenter Signed-off-by: Dan Williams Signed-off-by: Sarah Sharp

usb: hcd: Remove USB phy if needed

2013-12-09T02:00:51Z

This adds remove_phy flag to the HCD structure. If the flag is set and if hcd->phy is valid, the phy is shutdown and released whenever usb_add_hcd fails or usb_hcd_remove is called. This can be used by the HCD drivers to auto-remove the external USB phy when it is no longer needed. Signed-off-by: Valentine Barshak Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

USB: add a private-data pointer to struct usb_tt

2013-10-11T23:45:43Z

For improved scheduling of transfers through a Transaction Translator, ehci-hcd will need to store a bunch of information associated with the FS/LS bus on the downstream side of the TT. This patch adds a pointer for such HCD-private data to the usb_tt structure. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

USB: NS_TO_US should round up

2013-10-11T23:37:45Z

Host controller drivers use the NS_TO_US macro to convert transaction times, which are computed in nanoseconds, to microseconds for scheduling. Periodic scheduling requires worst-case estimates, but the macro does its conversion using round-to-nearest. This patch changes it to use round-up, giving a correct worst-case value. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman