user/sven/linux.git/include/linux/usb/hcd.h, branch v3.9

usb: add find_raw_port_number callback to struct hc_driver()

2013-03-25T17:39:17Z

xhci driver divides the root hub into two logical hubs which work respectively for usb 2.0 and usb 3.0 devices. They are independent devices in the usb core. But in the ACPI table, it's one device node and all usb2.0 and usb3.0 ports are under it. Binding usb port with its acpi node needs the raw port number which is reflected in the xhci extended capabilities table. This patch is to add find_raw_port_number callback to struct hc_driver(), fill it with xhci_find_raw_port_number() which will return raw port number and add a wrap usb_hcd_find_raw_port_number(). Otherwise, refactor xhci_find_real_port_number(). Using xhci_find_raw_port_number() to get real index in the HW port status registers instead of scanning through the xHCI roothub port array. This can help to speed up. All addresses in xhci->usb2_ports and xhci->usb3_ports array are kown good ports and don't include following bad ports in the extended capabilities talbe. (1) root port that doesn't have an entry (2) root port with unknown speed (3) root port that is listed twice and with different speeds. So xhci_find_raw_port_number() will only return port num of good ones and never touch bad ports above. Signed-off-by: Lan Tianyu Signed-off-by: Sarah Sharp

USB: add usb_hcd_{start,end}_port_resume

2013-01-25T23:06:01Z

This patch (as1649) adds a mechanism for host controller drivers to inform usbcore when they have begun or ended resume signalling on a particular root-hub port. The core will then make sure that the root hub does not get runtime-suspended while the port resume is going on. Since commit 596d789a211d134dc5f94d1e5957248c204ef850 (USB: set hub's default autosuspend delay as 0), the system tries to suspend hubs whenever they aren't in use. While a root-hub port is being resumed, the root hub does not appear to be in use. Attempted runtime suspends fail because of the ongoing port resume, but the PM core just keeps on trying over and over again. We want to prevent this wasteful effort. Signed-off-by: Alan Stern Tested-by: Ming Lei Signed-off-by: Greg Kroah-Hartman

usb: hcd: use resource_size_t for specifying resource data

2012-08-16T21:04:14Z

Changed the type of rsrc_start and rsrc_len from u64 to resource_size_t so that it behaves well with resource API's like *resource_size()* on both 32bit and 64bit devices. Signed-off-by: Kishon Vijay Abraham I Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

Merge branch 'usb-linus' into usb-next

2012-06-13T22:22:54Z

This is to pick up the changes to the option driver, which are needed for follow-on patches from Johan. Signed-off-by: Greg Kroah-Hartman

USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2

2012-06-13T20:11:39Z

This patch (as1558) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. A similar patch has already been applied as commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during suspend on ASUS computers). The patch supersedes that one and reverts it. There are two differences: The old patch added the flag at the USB level; this patch adds it at the PCI level. The old patch applied to all chipsets with the same vendor, subsystem vendor, and product IDs; this patch makes an exception for a known-good system (based on DMI information). Signed-off-by: Alan Stern Tested-by: Dâniel Fraga Tested-by: Andrey Rahmatullin Tested-by: Steven Rostedt Cc: stable Reviewed-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

USB: move transceiver from ehci_hcd and ohci_hcd to hcd and rename it as phy

2012-06-13T19:38:36Z

- to decrease redundant since both ehci_hcd and ohci_hcd have the same variable - it helps access phy in usb core code - phy is more meaningful than transceiver Signed-off-by: Richard Zhao Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

USB: Add support to enable/disable USB3 link states.

2012-05-18T22:41:58Z

There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: Alan Stern Signed-off-by: Sarah Sharp

Merge 3.4-rc6 into usb-next

2012-05-07T16:03:39Z

This resolves the conflict with: drivers/usb/host/ehci-tegra.c Signed-off-by: Greg Kroah-Hartman

USB: remove CONFIG_USB_DEVICEFS

2012-04-30T02:20:03Z

This option has been deprecated for many years now, and no userspace tools use it anymore, so it should be safe to finally remove it. Reported-by: Kay Sievers Signed-off-by: Greg Kroah-Hartman

USB: EHCI: fix crash during suspend on ASUS computers

2012-04-24T20:55:43Z

This patch (as1545) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. This fixes Bugzilla #42728. Signed-off-by: Alan Stern Tested-by: Steven Rostedt Tested-by: Andrey Rahmatullin Tested-by: Oleksij Rempel (fishor) Cc: stable Signed-off-by: Greg Kroah-Hartman